Regenerative braking energy calculator

Pick a drive cycle (UDDS, FTP-75, HWFET, US06, SC03, WLTC class 3b) or paste your own, set the car and the motor, and see the energy the brakes have to take every second, how much of it the motor can put back in the battery, and what stops the rest: drag, the cut-off speed, the torque and power limits, the axle share or the efficiencies. The Check tab finds which formula and unit gave your answer. Free, runs in your browser.

EPA dynamometer schedules · UNECE GTR 15 (WLTC) · Ehsani et al., Modern Electric, Hybrid Electric and Fuel Cell Vehicles · Updated 20 Nov 2026

Defaults: a 1,500 kg car with typical drag and rolling values, a motor that can brake with 250 N·m up to 60 kW through a 9:1 gear, regen down to 5 km/h. These are assumptions, labelled as such; set yours. Rotating mass adds the wheels' and motor's inertia (3 to 5% is typical; the challenge ignores it).

Kinetic energy shed874 Wh0.874 kWh, 3,148 kJ
At the brakes623 Wh71% of it; drag and rolling took the rest
Back into the battery511 Wh30% of the 1,690 Wh spent driving
Drive cycle speed against time, braking seconds coloured by whether the motor could take all of the braking0204060801000 s500 s1000 skm/hdrivingbraking, regenfriction brakes too
Motor torque each braking second would need against motor speed, with the motor's regenerative torque and power limit010020030001k2k3k4k5k6k7kN·mmotor rpm →base 2,292 rpmregen limitbraking, fitsover limit
  • 1369 s, 11.99 km, top speed 91.2 km/h. Driving energy at the wheels 1,402 Wh; the brakes take 44% of it.
  • Per km: 51.9 Wh at the brakes, 42.6 Wh back into the battery, 98.4 Wh/km net from the battery.
  • Peak braking power at the wheels 25.1 kW; peak charging power 20.8 kW.
  • The motor takes 99% of the braking (616 Wh); gearbox, motor, inverter and battery losses leave 511 Wh in the battery (105 Wh lost on the way).
  • 6.9 Wh (1%) goes to the friction brakes because of speeds under 5 km/h.
  • Base speed 2,292 motor rpm = 30 km/h: below it the motor can brake with 250 N·m, above it the torque falls as 60 kW ÷ speed.
Brakingkm/hKineticBrakesBattery
113–125 s52 → 044 Wh39 Wh32 Wh
299–333 s80 → 0102 Wh70 Wh58 Wh
380–397 s59 → 055 Wh46 Wh38 Wh
415–429 s48 → 038 Wh32 Wh26 Wh
488–505 s56 → 051 Wh43 Wh35 Wh
611–620 s43 → 030 Wh27 Wh22 Wh
747–763 s46 → 234 Wh27 Wh23 Wh
1302–1313 s47 → 035 Wh32 Wh26 Wh

The 8 biggest of 81 stretches of falling speed.

How do you calculate braking energy over a drive cycle?

Take the cycle's speed every second, in m/s. Every second the car slows down, it sheds kinetic energy; add it up:

For a 1,500 kg car over the EPA's UDDS city cycle that is 0.874 kWh (874 Wh, 3.15 MJ). That is the braking challenge in Skill-Lync's Introduction to HEV using MATLAB and Simulink course: "For a defined driving cycle, calculate the energy required for braking." Skill-Lync read all 792 public reports on it on 20 Nov 2026.

The brakes do not take all of it. While the car slows, drag and rolling resistance are still pulling it back, so part of the slowing is free. Work out the force the wheels need every second; when it is negative, the brakes (friction or motor) supply it:

With Crr = 0.01, Cd = 0.3, A = 2.2 m² and ρ = 1.2 kg/m³, the brakes on UDDS take 623 Wh, 71% of the kinetic energy shed. The chart shows the cycle; green seconds are braking the motor can take in full, orange ones need the friction brakes too:

Drive cycle speed against time, braking seconds coloured by whether the motor could take all of the braking0204060801000 s500 s1000 skm/hdrivingbraking, regenfriction brakes too

How much braking energy is in each drive cycle?

Same 1,500 kg car and default motor on every cycle the calculator carries. "Share" is the braking energy at the wheels as a share of the driving energy at the wheels: how much of the work done to move the car the brakes throw away.

CycleLengthKinetic shedAt the brakesShareInto batteryOf driving energy
UDDS1369 s, 11.99 km874 Wh623 Wh44%511 Wh30%
HWFET765 s, 16.51 km485 Wh184 Wh10%152 Wh7%
US06600 s, 12.89 km1,130 Wh673 Wh29%557 Wh20%
SC03600 s, 5.76 km495 Wh356 Wh48%294 Wh33%
FTP-751874 s, 17.77 km1,288 Wh899 Wh42%738 Wh29%
WLTC 3b1800 s, 23.27 km1,491 Wh877 Wh28%725 Wh19%

City driving is where regen pays: on UDDS and SC03 the brakes take 44% and 48% of the driving energy, and putting most of it back cuts the battery energy needed by about a third (30% on UDDS). On the HWFET highway cycle the brakes take only 10%: the car mostly loses its energy to drag, and regen returns 7%. A heavier car sheds more: at 2,000 kg the WLTC returns 1,012 Wh instead of 725 Wh. Adding 4% for rotating mass takes WLTC from 725 to 766 Wh.

Why can't the motor brake as hard at high speed as it can pull away?

Because braking uses the same torque-speed envelope as driving, mirrored. Up to its base speed a motor can give its full torque; above it, the inverter's current and voltage limit it to a constant power, so torque falls as power over speed:

Charging adds its own cap: the battery and inverter accept only so much power, often less than the motor can make. With the default 250 N·m and 60 kW through a 9:1 gear and a 0.31 m tyre, base speed is 2,292 motor rpm, 30 km/h. Each dot below is one braking second of the aggressive US06 cycle, at the torque it would need:

Motor torque each braking second would need against motor speed, with the motor's regenerative torque and power limit010020030002k4k6k8k10kN·mmotor rpm →base 2,292 rpmregen limitbraking, fitsover limit

Every second fits: US06's hardest braking needs 51.0 kW at the wheels for this car, under the 60 kW limit, so on standard cycles the motor's envelope is rarely what limits a 1,500 kg car. Halve the power limit to 30 kW and the fast stops no longer fit (red): 51 Wh goes to the friction brakes. Cut the torque to 100 N·m and 22 Wh is lost below base speed instead.

Motor torque each braking second would need against motor speed, with the motor's regenerative torque and power limit010020030002k4k6k8k10kN·mmotor rpm →base 1,146 rpmregen limitbraking, fitsover limit

The other end matters more on city cycles. At very low speed the motor's back EMF is too small to push useful current into the battery, so cars fade regen out near a stop and the friction brakes finish it. With regen down to 5 km/h, UDDS loses 7 Wh this way; stopping regen at 15 km/h loses 62 Wh.

How are electric and mechanical brakes coordinated?

Two common strategies (Ehsani et al. describe both):

  • Series, or cooperative, braking. The controller reads the brake pedal, gives the motor as much of the braking force as it can take (within its torque, power and charging limits) and lets the friction brakes add only the rest. It recovers the most, but needs a brake-by-wire or a blended hydraulic system. The calculator does this, with the motor's axle share at 100%.
  • Parallel braking. The friction brakes work as usual and the motor adds braking torque in proportion. Simpler, but the friction brakes always take a share. Set "Braking on motor axle" to 60% to see it: UDDS returns 306 Wh instead of 511 Wh.

The axle share also stands for stability: a front-drive car can only regen through its front wheels, and weight moves forward under braking, so the front can take a large share of a gentle stop but the rear brakes must carry their part of a hard one. Below the cut-off speed, in an emergency stop and when ABS acts, the friction brakes take over completely.

What goes wrong in the reports

Of the 792 reports, 545 work out an energy. The drive cycle named most is UDDS (173 reports); FTP is mentioned in 51, NEDC 21, WLTP 11, an Indian cycle 9, US06 and HWFET 8 each. The rest make up a short cycle of their own. The common slips:

  • Squaring the drop in speed (124 reports). ½m(vᵢ − v_f)² instead of ½m(vᵢ² − v_f²), against 33 that use the right form. They only agree when the car stops (v_f = 0). 57 of the 124 use the same MATLAB line, be(i) = 0.5*mass*(v(i)-v(i+1))^2, which squares the one-second drop: on UDDS at 1,500 kg it gives 59.6 Wh, 14.7 times too small. Hand-checked on a random 6: all 6 have it.
  • Joules ÷ 1,000 called kWh. 1 kWh is 3,600,000 J, not 1,000. The same "529.39 kWh" answer appears in 3 reports; a whole UDDS cycle at 1,500 kg sheds 0.874 kWh. At least 14 reports give a cycle's braking energy as more than 10 kWh, up to 2,630 kWh, the energy of a large EV battery pack many times over.
  • A power where an energy should be (28 of 156 stated totals). "Total energy required for braking is 16.8 kW" appears in 15 reports. kW is a rate; the energy over a cycle is kWh, kJ or J.
  • The speed left in mph or km/h. The EPA files give mph. Squared, an unconverted mph speed reads 5.00 times too high, km/h 12.96 times.
  • No road load. Only 21 reports take drag or rolling resistance off before calling it braking energy. It is the right first step (the kinetic energy is an upper limit) but on UDDS the brakes take 71% of it, on HWFET 38%.

On the theory questions the reports do better: 378 explain base speed, the constant-power region or field weakening, and 167 mention back EMF. 743 include the motor efficiency contour plot.

Braking energy in MATLAB, the right way

Reads the EPA UDDS file (two header lines, then seconds and mph), converts to m/s and sums ½m(v₁² − v₂²) over the seconds the car slows. It prints 0.874 kWh for 1,500 kg.

d = readmatrix('uddscol.txt', 'NumHeaderLines', 2);
t = d(:,1);  v = d(:,2) * 0.44704;      % mph -> m/s
m = 1500;                               % kg
dv2 = v(1:end-1).^2 - v(2:end).^2;      % v1^2 - v2^2 for every second
E = 0.5 * m * sum(dv2(dv2 > 0));        % only the seconds it slows down, J
fprintf('Braking energy %.0f J = %.3f kWh\n', E, E / 3.6e6);

To get the energy at the brakes, compute the force every second, F = m·a + Crr·m·g + ½ρCdA·v², and add up −F·v over the seconds it is negative, as the calculator does.

What this calculator does not cover

  • Efficiency maps. The motor, inverter, gearbox and battery have one efficiency each. A real motor is less efficient at low torque and low speed, where much city braking happens, so the battery figure is an upper estimate.
  • Battery limits. A full or cold battery accepts little or no charge; the calculator assumes it always can, up to the power limit.
  • Grade and wind. The cycles are flat and still-air. Driving downhill adds braking energy.
  • Driving limits. It does not check that the motor can follow the cycle when accelerating (US06 needs 80.6 kW at the wheels for this car).
  • The answer check tries the formulas and units found in the reports. A number from a cycle the calculator does not have, or a different mass, will not match: paste your cycle and set your mass.
Learn EV and hybrid design

Sizing a motor, a battery and a braking strategy against drive cycles is the daily work of EV powertrain teams. It is how Skill-Lync's EV and hybrid courses are built.

Frequently asked questions

How do you calculate braking energy for a drive cycle?

Take the speed every second in m/s and, for every second the car slows down, add ½m(v₁² − v₂²). For a 1,500 kg car over the whole UDDS city cycle that is 0.874 kWh (874 Wh). Drag and rolling resistance do part of the slowing, so the brakes themselves take less: 623 Wh with typical car values.

How much energy can regenerative braking recover?

It depends on the cycle more than the car. With a 90% motor and inverter, a 95% battery and a 97% gearbox, a 1,500 kg car gets 511 Wh back on UDDS, 30% of the battery energy it spends driving it, but only 7% on the HWFET highway cycle, where little braking happens.

Why can't an electric motor give full braking torque at high speed?

Above its base speed a motor is power-limited: torque falls as P/ω, the same as when it drives. The inverter and battery also cap the charging power. So at high speed the motor can brake only gently and the friction brakes take the rest. At very low speed the back EMF is too small to push useful current, so regen fades out near a stop.

What is the difference between series and parallel regenerative braking?

In series (cooperative) braking the controller gives the motor as much of the braking as it can take and the friction brakes only fill in, so it recovers the most. In parallel braking the motor adds a fixed share on top of normal friction braking, which is simpler but recovers less. In this calculator, a 60% share on UDDS returns 306 Wh instead of 511 Wh.

What is the UDDS drive cycle?

The EPA's Urban Dynamometer Driving Schedule, the city part of the US fuel economy test: 1369 seconds, 11.99 km, a top speed of 91.2 km/h (56.7 mph) and 81 stretches of falling speed. The EPA publishes it as speed in mph every second. FTP-75 is UDDS followed by its first 505 seconds again.

Is braking energy the same as kinetic energy?

No. Kinetic energy shed is ½m(v₁² − v₂²); the energy the brakes take is that minus what drag and rolling resistance absorb at the same time. On UDDS the difference is 29% for a typical car; on the faster HWFET it is 62%, because aerodynamic drag slows the car a lot at highway speed.

Related on Skill-Lync

Sources

  • US EPA, "Dynamometer Drive Schedules": uddscol.txt, ftpcol.txt, hwycol.txt, us06col.txt, sc03col.txt, speed in mph every second (files dated 2015-10). UDDS 1,369 s and 11.99 km, HWFET 765 s and 16.51 km, US06 and SC03 600 s each, FTP-75 here = UDDS + its first 505 s without the 10-minute soak.
  • UNECE Global Technical Regulation No. 15 (WLTP), Annex 1, WLTC class 3b, km/h every second, as transcribed in the European Commission JRC wltp package (v0.1.2a0; sum of speeds 83,758.6 = its checksum): 1,800 s, 23.27 km, 131.3 km/h top speed.
  • M. Ehsani, Y. Gao, S. Longo, K. Ebrahimi, Modern Electric, Hybrid Electric, and Fuel Cell Vehicles, 3rd ed., CRC Press 2018: road load, braking energy on drive cycles, series and parallel regenerative braking.
  • Skill-Lync, all 792 public "Week-11 Challenge: Braking" reports, read 20 Nov 2026: cycles, formulas, units and stated totals.
  • Skill-Lync, scripts/verify/regen-braking.py: downloads the EPA and WLTC data (checksums pinned), checks every value in the calculator's cycle file, recomputes every number on this page in separate Python code with an energy balance for each case, and writes the figures this page checks itself against at build time.
Free counselling

From a drive cycle to an EV powertrain career.

Turning a drive cycle into motor, battery and brake numbers is what EV teams hire for. A Skill-Lync counsellor can map the course that fits the role you want.

Talk to an EV course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.