American Chopper Motorcycle Design Project using Solidworks Objective: The objective of this project to learn the Solidworks interface and simultaneously sketch or model different exterior parts of American Chopper To assembly different parts of Chopper under the assembly environment To create a Photorealistic model of…

Aim: To Create a Base Bracket Plastic Component using the given Class A surface. Report on the Draft Analysis and the Creation of the tooling axis From the given Class A surface, connectivity of the Class A surface is checked by using the boundary command. The given Class A surface has 3 boundaries ie., one Outer boundary…

Aim: To Create a Switch Bezel Component using the given Class A Surface and the tooling axis. Report on the Draft Analysis and the Creation of the Tooling Axis Tooling Axis is the direction in which the mould or the core and cavity opens. Firstly, check visually for the best possible tooling axis and we find from the Z-direction…

Aim: To Create a Coin Holder Plastic Component using the given Class A Surface and perform draft analysis on Class A and Final Closed Surface.  Report on Draft Analysis and the Creation of the Tooling Axis Tooling Axis is defined as the direction in which the mould or core and cavity opens. Class A surface is…

Report of defining the given connectors and connector clip using Electrical Part design Workbench   DT06-08SA:  In Wiring Harness Assembly Structure, to define the connector as the electrical component following Steps are to followed: 1.Firstly, 3D Connector is created or download from the resource to begin…

Report on defining the Electrical Clip, Electrical backshell and Corrugated Tubes P-Clamp:  1. Download the P-Clamp 3D file from the given above link   Figure: P-Clamp  2. Define the geometrical parameters of the P-Clamp by creating the Entry point & plane, Exit point & plane and Base plane. 3. We create two points as…

Aim: To create the Bumper plasic Component using given Class A surface. Consider taking thickness of the component to be 3mm. Class A Surface: Surface made by the designer which si given as the input to work on. It is an aesthetic surface  Class B Surface: Surface below the Class A surface at certain…

Aim: To create a switch bezel from the given Class A surface and to create core and the cavity block. Switch Bezel  A switch bezel panel is nothing but a part which consists of the switch panels for the power windows and also has some place to rest the passenger’s hand on it. It is assembled on the main…

Aim: To route the wiring harness in Electrical Workbench and provide the protective covering to all the branches. Connector Definition: Firstly, the Connector 3D part file are downloaded from the resource  Next step is to define the Geometrical parameters of the connectors. The required geometrical parameters…

Aim: To Create rib and Screw boss for teh door handle considering the design rules Objective:  To create Tooling axis for the given Class A Surface To create Class-B and Class-C surface for the Door Handle To create Final closed surface and the final solid body of the Door Handle  To Create Rib and Screw Boss on the Class…

Aim: To route the Wiring Harness in the Electrical Workbench as shown in the given image as Harness A & B and inter connect them as the single harness assembly with proper annotations to the Connectors. Creation of CATPart and converting into IGS format Connector Definition: Firstly, the Connector 3D part file…

Aim: To Create Harness Assembly with protective covering and Flatten the harness assembly and place the Flatten view on Drawing Sheet. Connector Definition: Firstly, the Connector 3D part file are downloaded from the resource  Next step is to define the Geometrical parameters of the connectors. The required geometrical…

Sunseeker Predator Yacht Design Project using Solidworks Objective: The objective of the project is to learn the Solidworks interface simultaneously sketch or model different exterior parts of the Predator Yacht. To assembly different parts of the Yacht in the assembly environment. To create the Photorealistic model of…

Aim: To create a proper report explaining about the Bench-Marking and Compare atleast 4 Vehicles and provide a proper conclusion for the report, suggesting a single suitable vehicle among the comparison made with images.  Explain Bench-Marking.  Bench-Marking in the automotive industry invloves sturcutral comparison between…

Under-Body Coating  In Indian road conditions, a cars underbody is most prone to corrosion. Underbody coating provides long term protection from corrosion to car’s underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible but are prone to corrosion.Underbody…

Door Applique:  Aim: Create the Door applique Plastic Component from the given Class A Surface. To begin with, the tooling axis for the given Class A surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Design of Heatstakes and Locator as per the…

Aim: To create A-pillar design with Mastersection and using through the given Class A surface and create the engineering feature as Dog House   Objective:  To create a tooling axis  To create a Side core axis for the Doghouse To design the A pillar plastic component by creating Class B surface and Class C surface using…

Aim: To create assembly of Quick return motion mechanism and CV join mechanism Procedure: Create sketches of the Part of the assembly Create all the parts in the Part workbench Assemble all the parts in the Assembly workbench with proper constraints.Create Drafting of all the individual parts and the assemble Quick Return…

Aim: To create Door trim plastic component from the given Class A surface and create a Dog house as per the design consideration. To begin with, the tooling axis for the given Class A surfaceshould be created meeting the requirements of the draft angle and at the end perform the draft analysis on the model. …