Part A - Detailed study of anatomical basis of surgical procedures or Clinical management in association with any of the organ system . SELECTED 3 SYSTEMS:- A) CARDIOVASCULAR SYSTEM               The cardiovascular system consists of the heart, blood vessels, and blood. Its primary…

PROJECT(A) SELECTED SYSTEM:- GASTROLOGY SYSTEM GASTROINTESTINAL SYSTEM The gastrointestinal system is also known as the digestive system. It is a collective name of the alimentary canal and accessory organs. The alimentary canal forms a continuous tube that is open to the outside environment at both ends. The organs of…

 A MULTI-PARAMETER PHYSIOLOGICAL MONITORING SYSTEM A multi-parameter Patient Monitoring System (PMS) is used for multiple critical physiological signs of the patient to transmit the vital information like Electro cardiograph , Respiration Rate, Blood pressure etc. Therefore, multi parameter PMS has always been occupying…

Design a robotic surgery procedure to remove a healthy kidney from the donor using an AI guided Robot KIDNEY TRANSPLANT A kidney transplant is a procedure where a new donor kidney is placed in your body. This is typically done to treat kidney failure. Once attached, your new kidney will start to do the job of the…

Design and Develop a IOT based Wireless Wearable Health Monitoring System or a Home Healthcare System to monitor the physiological parameters of ECG, Heart Rate, Pulse Oximetry, Cuffless Blood Pressure and Body Temperature.   i-Product Name :- "All you need is THE RING"   cite:-https://www.smartringnews.com/posts/what-are-smart-rings-how-do-they-work…

PROJECT- "Design a Hospital Management system for better patient care" Healthcare management system (HMS) cite:-https://otakoyi.software/blog/healthcare-management-system-features-and-benefits Over the last few decades, the need to digitize the healthcare services industry has increased immensely. Having a system in place…

PROJECT 1:- Design a compelling LED desktop lamp for the Mass Market.   LED DESKTOP LAMP LED stands for the light-emitting diode. LED lighting products produce light up to 90% more efficiently than incandescent light bulbs. An electrical current passes through a microchip, which illuminates the tiny light sources…

PROJECT 2- DESIGN AND DEVELOPMENT OF PULSE OXIMETER (MEDICAL TECHNOLOGY) PULSE OXIMETER   Pulse oximetry is a noninvasive test that measures the oxygen saturation level of our blood. It can rapidly detect even small changes in oxygen levels. These levels show how efficiently blood is carrying oxygen to the extremities…

PROJECT 3- DESIGN AND DEVELOPMENT OF DISPOSABLE SYRINGE(MEDICAL TECHNOLOGY) DISPOSABLE SYRINGE Disposable syringes are becoming ever more common within the medical industry. This is due in no short part to both the want to streamline the workload and to prevent the spread of blood-borne illnesses. They’re also relatively…

PRODUCT 1- DESIGN AND DEVELOPMENT OF CRUTCH (MEDICAL TECHNOLOGY) AXILLA CRUTCH A crutch is a mobility aid that transfers weight from the legs to the upper body. It is often used by people who cannot use their legs to support their weight, for reasons ranging from short-term injuries to lifelong disabilities.…

PROJECT 1- DEVICE MASTER PLAN   (1)   DEVICE MASTER FILE They are MFs that may be used to provide confidential, detailed information [about facilities, manufacturing processes (e.g., sterilization), packaging materials, and contract packaging, as well as nonclinical and clinical study data] associated with Premarket…

PROJECT 2- CLINICAL INVESTIGATION PLAN (1)   Clinical Investigation Plan Clinical Investigation Plan is a Document that states the rationale, objectives, design and proposed analysis, methodology, monitoring, conduct and record-keeping of the clinical investigation. The Clinical Investigation Plan (CIP) is the key…

PROJECT 2- CLINICAL INVESTIGATION PLAN   (1) Clinical Investigation Plan Clinincal Investigation Plan is a Document that states the rationale, objectives, design and proposed analysis, methodology, monitoring, conduct and record-keeping of the clinical investigation. The Clinical Investigation Plan (CIP) is the key…

Project 1 Almost all Standards emphasize on Customer Focus. And customer focus is always about the Quality of Product and Service provided by the supplier. The word Quality is considered as “extent to which requirements are fulfilled”. Customer needs Quality, therefore, one of the ways to determine Customer Satisfaction…

PROJECT 2 DESIGN AND DEVELOPMENT OF BLOOD PRESSURE MONITORING SYSTEM(SPHYGMOMANOMETER): SPHYGMOMANOMETER A blood pressure monitor, or sphygmomanometer, uses an inflatable air-bladder cuff and a listening device or pressure sensor to measure blood pressure in an artery. This monitoring can be performed by using either of…

PROJECT 1 FOREARM CRUTCH Crutches are a sort of walking aid that serves to broaden a person's base of support. They transfer weight from the legs to the upper body and are frequently used by those who are unable to use their legs to maintain their weight (from short-term injuries to lifelong disabilities). Forearm crutch…

PROJECT-2 Additive manufacturing in Human Orthopedic Implants- Introduction- The technique of combining materials to produce products from three-dimensional model data, usually layer upon layer, as opposed to subtractive fabrication manufacturing procedures such as ordinary milling and machining, has been termed as additive…

REPORT Procedures: For V Block,                        Firstly, Opened sketcher workbench from mecanical work bench, where i have created geomentrical parameters to define for position sketch. by using profile tool i have created rectangle for the dimension of…

Procedures   Upper housing:  Sketch profile for upper housings are created in the sketcher workbench. Part modelig has done by using pad command in part workbench at dimension of 8 mm I have created sketch for way of blower exhaust system in the sketcher workbench curved shape of profile was created at radius of 10 mm …

REPORT Stock Support Base: - As shown in section view A-A, one side of the sketch was drawn and then revolved around vertical axis. To make handles shaped part, created a plane at an offset value given in the sketch, drew circle and padded it then another circle on this pad and extruded this up to main surface. This was…

Procedures   Piston: -   One side of the drawing given in section view A-A was drawn first and then revolved around the vertical axis to get the main piston body shape. Then created a plane at a distance of 25mm and made two circles on this plane and extruded it by 21.5 mm. Then created a pocket in…