Calculation of mix design for M35 grade concrete with fly ash. Aim: Calculation of mix design for M35 grade concrete with fly ash. Procedure: 1)Data: Grade of concrete : M35 Type of cement = OPC 43 grade conforming to IS 8112 Type of mineral admixture =fly ash conforming to IS 3812 (part 1). Maximum size of aggregate =…

A) Vastu shastra :  Vastu shastra is an ancient Indian science which are used as a guideline to design our home . By using the vastu shastra we can design the home in such a way that by proper use of natural sources like the sun, flow of a wind , moon ,water and earth to live the healthy and peaceful life . The good…

A) AIM : Create the geometries from P1 to P2 using all the coordinates system methods. These are following: Types of coordinate system is given below :     i) Absolute coordinate system    ii) Relative rectangular system    iii) Relative polar coordinate system   iv) Direct distance entry…

CRATE A FLOOR PLAN , FOOTING DETAILS AND ISOMETRIC VIEW USING AUTOCAD : SOFTWARE USED : AUTODESK AUTOCAD 2021 1) DRAW THE CROSS SECTION OF A LOAD BEARING WALL OVER THE SPREAD FOOTING. USE THE AUTO CAD SOFTWARE TO DRAW THE C.S FOOTING.                          …

1) Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left SOFTAWARE USED : AUODESK AUTOCAD 2021 AIM:To prepare the column schedule. Procedure:…

DRAFTING OF A VARIES GEOMETRIES DRAWINGS USING CHAMFER , FILLET AND OTHER TOOLS IN AUTOCAD . SOFTWARE USED : AUTODESK AUTOCAD 2021   1) TO DRAW THE GIVEN DRAWING BY USING AUTOCAD SOFTWARE                                  …

Q.1) Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors.              …

Aim - To draw the cabinet,floor plan,kitchen,column details and raft layout drawings:Procedure :Used tools in Auto Cad:-a. Line - To draw horizontal and vertical line of known distance- Command "L" -select the start point and end point.b. Rectangle - To draw rectangle .Command "REC" - select the frist point - click on…

AIM:          1.To create layout of plan and section, creating viewports, editing attributes and taking aplot.          2. To create a kitchen layout in A4 sheet and take a plot         3. To create multiviewports for industrial section drawing ,scaling…

Aim :      To create:           1. Template ,inserting text and attributes.           2. Doors of warehouse and placing it in blocks.           3. Electrical legend and making it blocks.           4.…

AIM:       To create:                A. Layouts of the Kitchen and provide hatches pattern as shown.                 B. Elevation of the plan created in the Challenges 7 and apply proper hatch to this elevation.    …

AIM : To draw the 3d isometric view of:            1. Building given plan and elevation             2. Facade of a building             3. Stair             4. Spread footing      COMMANDS USED:    1. Extrude - To give height to a surface or giving distance or hright in z axis of an object in x y plane so that i becomes…

  3D MODEL AND VIEW OF FURNITURE ELEMENT, ISOLATED FOOTING, AASTHO TYPE GIRDER,DROP COLUMN WITH PANEL AND WALL   AIM : To create 3D model and view of:                 1. Furniture element                 2. Isolated…

Design and Draft a layout of a residential building with the following details:       a. Plot Size: 60’x20’(18.3m x6m)        b. Orientation- Facing East        c. Develop the following:            1. Architectural Drawing (Floor Plan, Elevations, and Sections).            2. Structural Drawing (Column, Bean, Footing Plan).…

                           THREE DIMENSIONAL RENDERED VIEW OF A RESIDENTIAL BUILDING Aim : To draw a residentail building in 3d and create the rendered view .      Residential building with G+ 1 floors.      a.…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing.                                                     ANS:            …

                                       3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using Revit  Tools Used:    …

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School                 - I want to build Office Building from…

                        Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo 1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM:To create a set…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. AIM: To Exporting the Revit architecture and structure model to the Navisworks Cache file as discussed in…

1. 1. Write the steps involved to upload a .std file through web mail?    2. Name the different materials that can be designed using STAAD Pro.    3. Is it possible to capture images in STAAD Pro? If yes how?    4. Name the three ways by which you can create a model.    5. Write…

1. 1. How will you assign Circular section to column?    2. How will you assign Unit system to a .std model file?    3. What are the parameters to be specified while using “Bay Frame” option?    4. Name few codal standards incorporated in STAAD Pro software.    5. How…

1.1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define Primary Beams.  …

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:   Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2 Maximum slab…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements.…

What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate ? 1 (A)                                ANSWER :               Type:  Damage    …

1.Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) Ans.             Static Analysis:                       - Static analysis of structures considers static loads acting on the structure…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and its associated mode shape: The…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.                                                 ANS:    COMMENTS ON…

Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm  Columns : 800 × 800 mm  Slab : 150…

Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A        2) 7 span continuous beam along grid…

  Reinforcement detailing of columns in Etabs 2018.   The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections.   3A 3B   Provide details of longitudinal reinforcement for the…

The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model.   Extract values of longitudinal steel ratio, boundary element length and shear…

Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load, also…

The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

                                                                                          PROJECT : 1    PROJECT TITLE :                                  COMPARATIVE STUDY OF DIFFERENT STORY BUILDINGS FOR SEISMIC FORCES  AIM:           TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS…

1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. 2. A column of size 600x600 carrying an unfactored gravity load (DL+LL) of 1175 KN is to be supported on pile cap, which ultimately transfers load to the piles underneath.…

Plan View and 3D of the same is as belowIn this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location…

Given below is a floor plan of a building. The red lines running East-west are beams supported by the girders spanning North-South between columns. The floor system is 120 mm thick normal weight concrete floor. The floor finish and mech loads on the floor is 3 kPa. The live load on the floor is 5 kPa. All beams have cross…