Project - Data Handling and Interpolation   Data = xlsread ('VI.xlsx','A2:B25'); V=Data(:,1); I = Data(:,2); Vq = 17.3:0.1:0.9; Iq = interp1(V,I,Vq); plot(Vq,Iq,'B--o'):grid:xlabel('V_volt');ylabel('I_mAmp');hold; tiltle('voltage_vs_current');legend('interpolated_data'); VV =[-17.2 -17.1 -13.8 -13.5 -13.0 -12.5 -11…

we create a DC machine model and connect it to a control where we take the speed of the armature as reference and compare it with the output speed of the rotor. We consider the motor parameters as given below for a natural working condiotion. moment of inertia of rotor J as 0.01 Kgm^2 Motor viscous friction constant B1…

Que1.   In the above automotive diagram , on the right side we have 2 tail light , 2 dome light and one plate lamp along with the gas tank unit.  on the left down side we have the major battery and starter motor which is connected to the ammeter and then light switch where the  control of all the lights…

As per the requirment we create the design and input the parameers.  the model is shown below. The mechanics explorer out put is shown below   The scope output is given below.   Find the attached file of the simscape model , Parameters used and scope outputs attached

                                                        PROJECT NAME             The development of a forward energy-based fuel consumption model…

                                                         PROJECT NAME        The development of a forward energy-based fuel consumption model of a P1 hybrid…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation of it. Battery type Cathode Material Anode Material Electrolyte Material Separator   Material Anode reaction Cathode…

1. Simulate the 3 test cases from the harness dashboard and write a detailed report on the results https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms  We download the project model from the Matlab link that was provided and simulate it for different…

Project 1 Mechanical design of battery pack Battery pack capacity: 18 kWh Cell: ANR26650M1-B  AIM :  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions.   STUDY :  The ANR26650M1-B is the next generation of A123 Systems’ pioneering 26650 cylindrical cells,…

For a 10-cell series lithium-ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB.   Here we select a battery model from Matlab and set the capacity to 2Ah. we have connected 10 such cells in series and are connected to…

AIM :  Based on the concepts you have learned during the forward kinematics routine, write code that can solve an otto cycle and make plots for it.   OBJECTIVE : 1. Your code should create a PV diagram 2. You should output the thermal efficiency of the engine.   THEORY thermal efficiency of OTTO CYCLE In…

 AIM To solves the ODE which represents the equation of motion of a simple pendulum with damping.   OBJECTIVE  Your objective is to write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping THEORY  A point mass M is suspended from the…

AIM :  To write a program in python for curve fit.   Objectives :  1. What does popt and pcov mean? 2. What does np.array(temperature) do? 3. What does the * in *popt mean? 4. Write code to fit a linear and cubic polynomial for the Cp data. Explain if your results are good or bad.  5. What needs to…

AIM: Take a look at the data analysis video before you attempt this challenge. Your task is to write a script that does a data visualizer, compatibility check, and Basic performance calculation.   OBJECTIVES: Data visualizer Your script should take column numbers as the input and plot the respective columns as separate…

AIM :  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Steps The file is introduced to catia v5 . Then switch to mechanical part design and mark 2 entry/exit points on both sides . Create a reference plane along the points…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download connector…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…

Q1. Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view.     First of all, we import the week 4 challenge harness bundle to the catia V5  Create a new product file…

Statement of assignment: Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can…

  Statement of assignment: Route the Wiring harness on the Given car body and Prepare to to flatten the view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can…

  Statement of assignment: Route the Wiring harness on the Given car body and Prepare to to flatten the view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be…