Automotive benchmarking Automotive bench marking is a process to comparsion of two products some small difference in performance. Automotive bench marking is analyzing process that process is used to selected best of similar products based of that performance. Case Mr. D.S. Pughazhyendhi is a married man who lives…

                                                          Underbody coating   Underbody Coating is a sprayable coating, which protects the under surface of the…

Hood design The hood or bonnet is a hinged cover over the engine of motor vehicles that allows access to the engine compartment, or trunk for maintenance and repair. The inner panel provides strength while the outer panel functions as the metal cover. Hood comes from the Old English word hod which means a hood, a soft…

 Section modulus section modulus is ageometric property for a given cross secton used in the design of beam or members, its also at the polar modulus or the torsional section modulus .in other case geometric are used to the design included area for the tension and shear ,radius of gyration foe compression and moment…

Fender design wheel arch 1.wheel arch wheel arch is semi circular part of the fender positioned aboventhe wheel of the vehicle. The design of wheel arch of a fender should be such that it must be a sheild to protect the passenger's campartment. The wheel arc of the fender regulation differ from the various country. 2.Objective…

Introdution  Design of any product starts from the requirements . the deisgn engineer sketches the product based on the requirements . then convert to 3D models . so the design engineer is to design product that can be easily manufactured and with less cost. Fender Fender is the American English term…

                                                              ROOF ASSEMBLY An automobile roof or car top is the portion of an automobile that sits above…

                                                                             INTRODUCTION: A door is a hinged part which is used…

AIM Create the Base Bracket Plastic component through the given Class-A surface. MAIN REPORT GIVEN DATA To perform the surface part by using given surface . to create the dummy tooling axis because the we don't knowmoriginal toling axis. after that we use the bisecting line to create the original tooling axis. bisecting…

 AIM Create the Switch Bezel Plastic component through the given Class-A surface. Introduction- The control panel bezel is the frame part of the window switch that holds its switch covers and buttons into place. Moulding is the method used to manufacture the plastic trims of an automotive by most OEM’s, hence…

AIM Create the Coin Holder Plastic component through the given Class-A surface.  main report  tooling axis Tooling axis creation The direction in which the mould open and closes is called the tooling axis direction. Check the connectivity of the surface and ensure there will be no gap between the surfaces and…

AIM Create the Bumper Plastic component through the given Class-A surface. given data INPUT GIVEN: A-Surface Thickness of component is 3.00mm  Draft angle is 3 degrees.   CHECKING THE INPUT - A SURFACE:  The A-surface or the styling surface is first checked for any gaps and other issues in its surfaces.…

AIM Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  MAIN REPORT    1. CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The…

aim Create the rib for the Drill Handle considering the design rules mentioned in the video.  main report to create the rib byusing given design rules  asusal to create the tooling axis to ensure the part was the correct direction    to create the class b surface by using the offset command and to make…

Aim Create the Dog House for the Door Trim considering the design rules. Class A Surface:  To start the design process we need to find out the tooling axis for the surface and check the drafts using the Draft Analysis tool in CATIA. And Publicize the A surface Tooling Axis:  Take a draft analysis with A surface…

  Aim: To create a Door Trim-Heat Stacks & Locators through a given input Class A Surface and Tooling axis to Draft Analysis on the A surface and  final plastic component.   REPORT: Door Trim Dog House:   Class A Surface:  To start the design process we need to find out the tooling axis for the surface and check the drafts…

REPORT: Door Trim Dog House:   Class A Surface:  To start the design process we need to find out the tooling axis for the surface and check the drafts using the Draft Analysis tool in CATIA. And Publicize the A surface. Tooling Axis:  Create an Extract on a flat surface and point on surface 0mm and Create…

main report slotted lever base reactangular slider   connecting rod pin final assembly   given datas part2    

AIM given data Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2 (https://www.te.com/usa-en/product-2-174357-2.html?source=header-match) Tyco 85229-1 – (https://www.te.com/usa-en/product-85229-1.html?q=85229&source=header)   to consider various factor to define…

main report  Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties.    further move next step to define parameters process: Create two points one as entry and another as exit point. create planes at two points and another…

AIM  Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing. given data to provide the electrical properties The electrical connectors are represented by numbers in the above figure. There are 8 different types of…

AIM  To flatten the wire harness assembly completed in week 4 assignment and place the flattened view on a drawing sheet. OBJECTIVE:   To flatten the wire harness assembly completed in week 4 assignment. To orient the wire bundle as shown in the layout.   c-dt06-2s Connector connection point: Create midpoint…

 given title for this projectRoute the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.Available connector 3D data can be used, or you can…

GIVEN  Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can download the…

  Aim : To create a CAD model of a side door trim panel from given class A surface . Objective:  a) Creation of side door trim panle from given class A surface . Apply thickness to it and use attachment features .  b) Creation of flanges and heat stakes from given master sections . c) Creation of dog…

Aim - To make an Entire surface Models of Car Rims. Objective - Our objective here is to make surface models of the car rims, 1) Provided by Skill-Lync and 2) Anyone of Our Choice, Surfacing is to be done using Auto Desk ALIAS INTRODUCTION Autodesk Alias (formerly known as Alias StudioTools) is a family of Computer-aided…

  CONCEPT MODELLING OF CARBUMPER ALIAS SOFTWARE objective The main of the project is to create a concept model of the bumper of Abarth 500 car, using the curves and surface generation features with the help of Alias software. INTRODUCTION: Auto desk alias (formerly known as alias studio tools)The out side portion…

                                               Tittle: Side fender modelling Objective : To build a concept modelling of side fender using curves and surfaces Introduction: Fender is the American English…