Title of the Project: American Copper Bike Objective: To learn SolidWorks by modeling the different parts of the American Chopper Bike and its assembly using different tools like line, circle, spline, extrude, revolve, mirror, fillet etc. Introduction: SolidWorks is a professional software used by design engineers in order…

1. Radar Mast   a) Isometric view      b) Front View      c) Side View      d) Top View      e) Feature Tree               2. Sunseeker Predator Yacht assembly   a) Isometric View      b) Front…

                                                                 Benchmarking Benchmarking is defined as a structured comparison between similar products,…

Underbody Coating Definition: - Underbody coating means any coating labelled and formulated for application to wheel wells, the inside of door panels or fenders, the underside of a trunk or hood, or the underside of the motor vehicle. Broadly, it is the process of coating a thick resilient material to the underbody or…

Title of the project:  Hood Design Assembly in NX-Cad Objective: To use the necessary design parameters to develop the hood assembly from hood outer panel, hood inner panel, hinge and striker by creating necessary embosses and reinforcement in NX Cad. Introduction: Hood is the covering for engine in front engine vehicles,…

                               Section Modulus Calculation and Optimization Objective: To calculate the section modulus of a hood section and optimize it to increase its…

Title of the project: Fender Design Challenge Objective: To design various mounting points like Drip Area mounting, Sill Mounting, Bumper mounting, A-Pillar mounting and Baffle mounting on the front fender with design consideration. Introduction: A fender is the curved portion of the car’s body that sits over and houses…

Title of the project:  Roof Design Aim: To design the roof of the car along its components by following the master section and design parameters. Objectives: To design the essential flanges ( i.e. Ditch Area ) and the reinforcement using roof styling as input. To determine the heat distortion criteria test of the…

Title of the project: Backdoor Design Aim: To design backdoor of a Hatchback car along its components by following the styling surface and the design parameters. Objectives: To understand the functional requirement of the backdoor. To design the backdoor inner panel, outer panel upper and lower, necessary reinforcement…

Title of the project: Fender design-Wheel Arch Challenge Objective: to calculate the wheel arch area of the given fender and prove whether the car will pass the European Standards or not. Introduction: Wheel Arch is the shaped part of the bodywork of a car or other vehicle that allows the wheel to be accessed, and in the…

                                                         Draft Analysis on a Fan Cover Aim: To create the tooling axis for the given fan cover model and then perform draft analysis…

                                                                  BASE BRACKET DESIGN Objective: To design Base Bracket and perform draft analysis on the model…

                                                         …

                                             DOOR ARM REST DESIGN Objective: To design Door Arm Rest and perform draft analysis on both the Class A Surface and the final model along the tooling axis meeting…

                                                                 COIN HOLDER DESIGN  Objective: To design Coin Holder Plastic Component through the given…

                                     CORE AND CAVITY DESIGN Objective: To create core and cavity blocks for the Switch Bezel Component along with parting surface and parting line. Introduction: Class A Surface: In automotive…

                                                  RIB DESIGN Objective: To…

                             Boss and Dog House Design Objective: To create the Boss and the Dog House for the Centre Console Coin Holder considering the design rules. Introduction: Boss: Bosses are small cylindrical elements in a design. They are…

                                                 DOOR APPLIQUE DESIGN Objective: To create solid model of the Door Applique from the given Class-A Surface and add engineering features like Heat Stakes…

                    B-PILLAR DESIGN Objective: To design a B-Pillar along with the Attachment Features following the master section and Class-A meeting all the design requirements. Introduction: Class A Surface: In automotive…

                                   ASSEMBLY WORKBENCH Aim: To create the part models and assembly of the components from the given 2d-drawings and then to create drafting. Introduction: Assembly modeling: Assembly modeling is a process…

                    FINAL PROJECT (DOOR TRIM PANEL) Objective: To design the part models of DOOR TRIM PANEL inside the assembly workbench from given input as Class-A Surface and then add engineering features like ribs, heat stakes,…