Assembly of Quick-Return Mechanism and CV Joint in CATIA V5

BACK DOOR DESIGN OBJECTIVE:- Design a back door of car which fulfills the visibility criteria for the passenger. INTRODUCTION:- Back door is access to the boot space of the car. Back is designed as such that it increases the space of boot and do not hinder in the visibility of passenger. Back door can be of different type…

TITLE :- AUTOMOTIVE ROOF DESIGN OBJECTIVE: - To design roof of car and do curvature study for heat distortion and snow load criteria Introduction:- An automotive roof is that part of car which sits above the passenger compartment. The main purpose of roof is to protect passenger from rain, sun, and other external element.…

  SECTION MODULUS CALCULATION AND OPTIMIZATION Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section or the beam section. Higher the section modulus of a structure, the more the resistive it becomes to bending.…

TITLE OF THE PROJECT:- FRONT FENDER OF CAR OBJECTIVE: - To design BIW front fender of car and all it’s mounting to attach it to main body. INTRODUCTION:- Fender is an English term for the part of an automobile that frames a wheel well. Its primary work is to prevent rock, sand, mud, liquids and other road spray from…

                                                                                          …

FINAL INDEPENDENT PROJECT:- FERRARI LAFERRARI 2013    ABSTRACT:- AFTER LOT OF RESEARCH I DECIDED TO MODEL FERRARI LAFERRARI 2013 BECAUSE OF FURTURISTIC DESIGN WITH EXTREME AND SENSUAL LINE. HERE I REPORT THAT APPROACH TAKEN FOR THIS MODEL IS DESIGING THEN ASSEMBLY AND THEN RENDERING IN SOILDWORKS. THE FINAL RESULT…

Title of the project:- Surface modelling and assembly of Sunseeker Predator Yacht Objective:- The main objective of this project is to model a sunseeker predator yacht using mainly surface modelling in solidwork and create photorealistic renders of yatch in solidwork visualize . Introduction:-In this project, I have modeled…

TITLE OF THE PROJECT:- DESIGING AND MODELING OF AMERICAN CHOPPER OBEJECTIVE:-Understanding and mastering the solidworks interface and implementing the features and sketch tools available in solidworks like convert entities,offset and many more,features like extruded bose,shell feature, split tool,projected curve , referance…

UNDERBODY COATING:- Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…

CASE STUDY :- BENCHMARKING Benchmarking is a initial phase in automobile industry when any new product has to come into life. Basically it compare two or more similar product, service , or process on some dimensions of performance.In automotive industry benchmarking is done at two levels named as benchmarking-1 and benchmarking-2.…

TITLE OF THE PROJECT:- METAL BRACKET-II OBJECTIVE:-To Create Metal bracket using sheet-metal in NX CAD DESIGN METHODOLOGY:-                          DESCRIPTION:- For this metal bracket sketch is very important and critical part. Sketch will give the desire…

TITLE OF THE PROJECT:- SHEET METAL PART FOR ODD SHAPE OBJECTIVE:- To learn how to convert Non SM part into SM part and some feature to it. DESIGN METHODOLOGY:-                                            DESCRIPTION:-…

TITLE OF THE PROJECT:- BRACKET OBJECTIVE:- To create metal bracket using NX DESIGN METHODOLOGY:- DESCRIPTION:- Create the sketch for the bracket using the given dimension fro the bracket. Now use counterflange to create the sheet-metal part from the sketch with thickness of 3mm and length of 200mm . Create another sketch…

TITLE OF THE PROJECT:- BOX ASSEMBLY OBJECTIVE:-To Create Box Assembly of sheet-metal DESIGN APPORACH:- TAB FLANGES CORNER HEM FLANGE MIRROR DIMPLE BEAD UNBEND REBEND DESCRIPTION:- Tab is created as for creating the box of dimension 150mm*200mm. Create flange of 200mm from both edge of tab. Now again create flange of 70mm…

 TITLE OF THE PROJECT:- SHEET-METAL CASING OBJECTIVE:- To Create Sheet-Metal Casing using NX CAD INTRODUCTION:- This is simple design of casing made of sheet metal which will be used to cover which will protect the component from surrounding. DESIGN METHODOLOGY:- Creation of TAB Normal cutout Bend Creation of Flanges…

TOPIC:- DOOR TRIM PANEL OBJECTIVE:- To create different part of door trim and attachment feature. INTRODUCTION:- Car doors are designed to facilitate ingress and egress by car passengers. Door are mainly made of two component one is BIW which is extrior part and another is trim which is interior part which is made of plastic.After…

AIM:- TO MODEL AND ASSEMBLE QUICK RETURN MECHANISM AND CV JOINT EXPLAINATION:- All component is designed sparately in part workbench using the given input. EXPLAINATION FOR QUICK-RETURN MECHANISM ASSEMBLY First all components are imported into the assembly workbench. I have fixed the first component to take it as referance…

TITLE:-  DESIGN OF DOOR APPLIQUE AIM:- TO DESIGN DOOR APPLIQUE WITH ATTACHENT FEATURE EXPLANATION:- CREATION OF CLASS A SURFACE: Join the class A surface to fill the little gap which cannot be seen by naked eyes. Like this we get complete class A surface. Thicken the door attachment surface to like 2mm. CREATION OF…

AIM:- Design for B Pillar master section development INTRODUCTION:- Pillars are those vertical component of car which provide structural support roof-top and is designed for latching the front door and mounting the hinges of rear door. Pillar are divided into 3 type A,B,C in sedans but can go to D for SUV. In this project…

AIM:-TO DESIGN BASE BRACKET USING CLASS A SURFACE AND DOING DRAFT ANALYSIS OF PLASTIC DESIGN EXPLAINATION:- Base bracket class A surface is imported to catia interface. ERROR some gap were found between two surface of class A surface.Then one of the small surface is  improved by extracting and joing again by increasing…

OBJECTIVE:- CREATING TOOLING AXIS FOR FAN COVER AND PERFORMING DRAFT ANALYSIS INTRODUCTION:-Draft analysis is performed because no component can be manufactured without giving draft.This is so beacuse if the ejecting surface of component is 90 degree from the base the component will cling with the mold which can cause…

REPORT FOR SWITCH BEZEL EXPLAINATION:- TOOLING AXIS In this plastic component tooling axis has been created by using compass method. Compass is brought to the surface and placed anywhere on the surface. Now by moving compass we check that all surface are gree or not. If so we lock the compass direction by right clicking…

 AIM:- CREATION OF RIBS FOR COIN HOLDER WITH TOOLING AXIS. TOOLING AXIS CREATION:- For this component we bisect with the plane and component. By seeing bisect we observe that one wall is at 90degree. For creating tooling axis for this component just create a normal line using the point we created intially. RIBS CREATION:-…

REPORT FOR COIN HOLDER DESIGN WITH DRAFT ANALYSIS EXPLANATION:- CLASS A SURFACE  Class A Surface of coin holder is imported first. Extract base surface and create new axis system by creating a point on the surface. Now check the class A surface by using boundary, now untrim the boundary into 2 element which will be…

AIM:- COIN HOLDER WITH ALL ENGINEERING FEATURE EXPLANATION:- CLASS A SURFACE CREATION Class A Surface of coin holder is imported first. Extract base surface and create new axis system by creating a point on the surface. Now check the class A surface by using boundary, now untrim the boundary into 2 element which will be…

AIM:-DESIGN OF SWITCH BEZEL AND ITS CORE AND CAVITY EXPLAINATION:- TOOLING AXIS In this plastic component tooling axis has been created by using compass method. Compass is brought to the surface and placed anywhere on the surface. Now by moving compass we check that all surface are gree or not. If so we lock the compass…