AIM:  write a program that solves the following second ODE using MATLAB.   THEORY : Ordinary Differential Equations(ODEs) - An ordinary differential equation (ODE) is a differential equation containing one or more functions of one independent variable and the derivatives of those functions.The term ordinary…

AIM: Write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function.   INTRODUCTION Optimisation : Optimisation is a decision-making process, it helps to find the best results Under a set of prioritized criteria or constraints. it is a procedure that is executed…

AIM: Write a function that extracts the 14 coefficients and calculates the enthalpy, entropy, and specific heats for all the species in the data file.   OBJECTIVE:  To develop a function that extracts the 14 coefficients and calculations the enthalpy, entropy, and specific heat for all the species in the…

AIM:  To Create a Rankine Cycle Simulator using OCTAVE/MATLAB To plot the corresponding T-s and h-s plots INTRODUCTION A Rankine cycle is an idealized thermodynamic cycle or heat engine in which fuel is used to produce heat within a boiler, converting water into steam which then expands through a turbine producing…

AIM: To Make a Simulink model of Doorbell using a solenoid block with the following details   Given diagram: Solenoid: It is a type of electromagnet formed by a helical coil of wire whose length is substantially greater than its diameter, which generates a controlled magnetic field. The coil can produce…

AIM: Implement control logic of a “washing machine” using Stateflow as per the given sequence      2. Make a Simulink chart for the “Gear shift” logic as per the below conditions   1. Implement control logic of a “washing machine” using Stateflow as per the given…

 Aim: Prepare a technical report explaining the model properties & comments on the results. Introduction: an all-terrain vehicle (ATV) is defined as a motorized off_highway vehicle designed to travel on four low-pressure or non-pneumatic tires, having a seat designed to be straddled by the operator and handlebars…

 AIM: To explain Benchmark with presently available cars in the market for the following case.   Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits…

Aim: To write one page about Underbody coating and its purposes. UNDERBODY COATING: Underbody coating provides long-term protection from corrosion to a car's underbody. It also protects parts like internal body panels, frame rails, and other inner cavities that are not physically accessible but are prone to corrosion.…

AIM: To design components of the hood of a car and assemble them together.   INTRODUCTION: Hood or Bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment or trunk on the rear engine and some mid-engine vehicles for maintenance and repair   On front-engined…

Aim: To design a fender using NXCAD software by using the master sketch which is provided.   INTRODUCTION OF FENDER:   The main purpose of the fender is to prevent sand, rocks, liquids,and other road spray from being thrown into air by the rotating tire. there are two types of fender 1 full bumber type 2 half…

AIM: Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.   INTRODUCTION: The fender is a part of an automobile vehicle body that frames a wheel well. Its primary purpose is to prevent sand, mud, rocks, liquids, and other road sprays from being thrown…

AIM:  To calculate the Section Modulus of Hood by using the formula   INTRODUCTION section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. other geometric properties used in the design include an area for tension and shear, the radius of gyration…

AIM: To create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements for the given Roof styling.   INTRODUCTION:                  An automobile roof or car top is the portion of an automobile that sits above…

AIM: To Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  PROCEDURE FOR DESIGNING THE BASE BRACKET PLASTIC…

AIM: To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

AIM: To Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

AIM: To Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 3 mm…

AIM: To Create the Core and cavity blocks for the switch bezel.    PROCEDURE: Class A surface: Class A surface is a Styling surface or aesthetic surface get it from the styling team. we will design the plastic component by using the Class A surface as input. Class B surface:Class B surface is to be creating the…

AIM: To Create the rib for the Drill Handle considering the design rules.  Take the Thickness of the component to be 2.5 mm PROCEDURE FOR DESIGNING THE CLOSED DOOR HANDLE COMPONENT : Class A surface: Class A surface is a Styling surface or aesthetic surface get it from the styling team. we will design the plastic…

AIM: To Create the Dog House for the Door Trim considering the design rules. Take the Thickness of the component to be 2.5 mm PROCEDURE FOR DESIGNING THE CLOSED DOOR HANDLE COMPONENT : Class A surface: Class A surface is a Styling surface or aesthetic surface get it from the styling team. we will design the plastic…

AIM: To Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

AIM: To create A pillar Design with Master Section. Taken the Thickness of the component to be 2.5 mm from the master section PROCEDURE FOR DESIGNING A PILLAR COMPONENT : Class A surface: Class A surface is a Styling surface or aesthetic surface get it from the styling team. we will design the plastic component by using…

SHEET METAL CASING DESIGN  Objective: To design an casing using the sheet metal application in siemens NX. Introduction: Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheet metal is considered foil or sheet, and pieces thicker than…

Title : SHEET METAL BOX ASSEMBLY Objective: To Design an Box Assembly using the sheet metal application in siemens NX. Introduction Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheet metal is considered foil or sheet, and pieces…

  DESIGN A ODD SHAPED ENCLOSURE Objective : To design an Odd Enclosure using the sheet metal application in siemens NX. Introduction  Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheet metal is considered foil or…

Title of the Project: Design of a sheetmetal Bracket Objective: To Design an Bracket using the sheet metal application in siemens NX. Introduction  Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheet metal is considered…

AIM: To create a Door interior part from the inputs of class A surface along with master section by following the design rules. Taken the Thickness of the component to be 2.5 mm from the master section   PROCEDURE FOR DESIGNING DOOR INTERIOR PARTS: Class A surface: Class A surface is a Styling surface or aesthetic surface…

Title of the Project: SHEET METAL _ BRACKET Objective: To Design an metal bracket using the sheet metal application in siemens NX. Introduction: Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Thicknesses can vary significantly; extremely thin sheet metal is considered foil or…

  AIM: To creat the assemblies with the help of given 2d drawins. MODEL 1 ASSEMBLY - CV JOINT 1. CV JOINT PARTS WITH ISO CONSTRAINS PART - 1 PART - 2 PART - 3   FINAL CV JOINT FINAL ASSEMBLY     MODEL 2 ASSEMBLY - QUICK RETURN MECHANISM   2. QUICK RETURN MECHANISM  PARTS WITH ISO CONSTRAINS…

AIM: To create a Door interior part from the inputs of class A surface along with master section by following the design rules. Taken the Thickness of the component to be 2.5 mm from the master section   PROCEDURE FOR DESIGNING DOOR INTERIOR PARTS: Class A surface: Class A surface is a Styling surface or aesthetic surface…

Assemble and apply GD&T to the butterfly valve assembly drawing Creating the Assembly of the Butterfly Valve by using Siemans NX. Operations Move Components Assembly Constraints First inport the all individual parts of the Butterfly valve in the Assembly workbench by using add command. Body, Stem, Retainer, Plate, Lever,…

WIRING HARNESS DESIGN In this challenge, first we are going to set up the geometrical parameters for the given cad models which are connectors and a connector clip. Setting up Geometrical Parameters C-DT06-08SA Connector       174357-2 Female Connector      85229-1 Cavity (Connector Clip)…

Wiring Harness Routing and Packaging Rules In this challenge, We are first going to define a mechanical cad component electrically by setting up the geometrical parameters and then using the Electrical Pat Design workbench we will define the electircal support. In order to set the geometrical parameters for defining the…

In this challenge Prepare Interconnection the harness A and B in one product file with help of to define mechanical components electicaly and prepare harness A and B layout as per given. Given Layouts Harness A Harness B Using Connect Electrical Devices option we will connect these harnesses. Checking the bundle continuity…

Wiring Harness Routing Given Wiring Harness Routing Layout we are going to route the wiring harness layout using Electrical Workbench. Connectors that are given to us includes, DT06-4S DT06-6S DT06-2S DT06-08SA The connectors are the mechanical parts that need to be converted into electrical parts in order to route the…

AIM:- To Flatten the given Wiring Harness by Electrical Harness Flattening Workbench and Drafting the Flatten Wiring Harness. Given Above Harness Flatten in Electrical harness Flattenting Workbench HARNESS FLATTENING: We go the Harness Flattening Workbench and define the Flattening Parameters. We use the Extract command…

Aim:- To Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Apply Protection coverings as required. Given  Engine DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Provide clips/clamps as per requirement. Make sure that there is no any fauling case while designing the wire harness. Additional…

Aim:- To route the wiring harness on the given Back Door of car body and prepare the flatten view drawing in CATIA V5.  Given Back Door  DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Provide clips/clamps as per requirement. Make sure that there is no any fauling case while designing the wire harness. Additional clips/clamps…