Menu

Workshops

Projects

Blogs

Careers

Find Jobs


For Business / Universities

Corporate Training

Hire from US

Academic Up-skilling


All Courses

Choose a category

Loading...

All Courses

All Courses

logo

Loading...

FOR BUSINESSES

Corporate Upskilling

Hire from Us

FOR Universities

Academic Training

More

Chinnaiyan B

Mechanicaliophile

Skills Acquired at Skill-Lync :

  • CFD
  • NUMERICAL-ANALYSIS
  • MATLAB
  • OPENFOAM
  • ANSYS-FLUENT
  • STRUCTURAL-MESHING
  • ANSA

Introduction

Can do it again & again I Reciprocate...!

24 Projects

Week 3.5 - Deriving 4th order approximation of a 2nd order derivative using Taylor Table method

Objective:

sceme derivation: central differencing scheme: no of nodes:       the number of nodes = p+q-1        p is order of derivatives        q is order of approximation         the number of nodes = 2+4-1 =>5. Derivation: (∂^2u/∂x^2)=(af(i-2)+bf(i-1)+cf(i)+df(i+1)+ef(i+2))/dx^2 …

calendar

28 Feb 2022 10:26 AM IST

    Read more

    Week 5.1 - Mid term project - Solving the steady and unsteady 2D heat conduction problem

    Objective:

    Aim:      i) To Solve the 2D heat conduction equation by using the point iterative techniques.     ii) To solve implicit iterative technique equations.                  1. Jacobi                 2. Gauss-seidel                 3. Successive over-relaxation    iii) To write code for implicit and explicit schemes Given:…

    calendar

    05 Mar 2022 05:18 AM IST

      Read more

      Week 9 - FVM Literature Review

      Objective:

      Objective 1. Finite Volume Method(FVM) 2.The major differences between FDM & FVM 3.The need for interpolation schemes and flux limiters in FVM 4.use the 1D linear heat conduction equation 1.Finite Volume Method         The finite volume method(FVM) is a discretization technique for partial…

      calendar

      17 Mar 2022 08:33 AM IST

        Read more

        Week 7 - Simulation of a 1D Super-sonic nozzle flow simulation using Macormack Method

        Objective:

        AIM Solve the conservation and non-conservation forms of the governing equations of 1D subsonic-supersonic nozzle by using  MacCormack method. Objective 1. Steady-state distribution of primitive variables inside the nozzle.2. Time-wise variation of the primitive variables.3. Variation of Mass flow rate distribution…

        calendar

        20 Mar 2022 01:19 PM IST

          Read more

          Week 8 - Simulation of a backward facing step in OpenFOAM

          Objective:

          Aim:       1.To simulate an incompressible-laminar-viscous flow through the backward facing step geometry.          2.To  perform a transient simulation, The solver can be chosen based on the described physics of the flow. Conditions:        Case 1 -…

          calendar

          26 Mar 2022 01:48 PM IST

          • CFD
          Read more

          Week 11 - Simulation of Flow through a pipe in OpenFoam

          Objective:

          Objective: Calculation of Flow variables.  Generation of blockMeshDict using the wedge boundary condition. create the blockMeshDict file in MATLAB such that the mesh is automatically created for any wedge angle. Simulating the pipe flow in OpenFoam using icoFoam solver. Post process the velocity profile and shear…

          calendar

          31 Mar 2022 05:17 PM IST

          Read more

          Week 12 - Validation studies of Symmetry BC vs Wedge BC in OpenFOAM vs Analytical H.P equation

          Objective:

          Objective: To simulate an axis-symmetric laminar flow through the constant cross- sectional of the pipe by applying the symmetry boundary condition. To simulating for the mentioned angles i.e for 10,25,45 degrees using both symmetry and wedge boundary conditions and validate them HP equations.          Entrance length:…

          calendar

          05 Apr 2022 02:35 PM IST

          Read more

          Week 1- Mixing Tee

          Objective:

          1.Objective: For this challenge, we have created two versions of the mixing tee. One of them is longer than the other. Our job is to set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C.  Use the k-epsilon and k-omega SST model for the…

          calendar

          14 Apr 2022 01:29 PM IST

          Read more

          Week 2 - Flow over a Cylinder.

          Objective:

          1.Aim:       Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street.  2.Objective: Simulate the flow with the steady and unsteady case and calculate the Strouhal Number for Re= 100.  Calculate the coefficient of drag and lift over a cylinder by setting the Reynolds number to 10,100,1000,10000…

          calendar

          17 Apr 2022 01:01 PM IST

            Read more

            Week 3 - External flow simulation over an Ahmed body.

            Objective:

            1.Objective:     To do external flow over the Ahmed body.  Q1.1 Ahmed Body The Ahmed body was described originally by S. R. Ahmed in 1984 The Ahmed body is a simplified vehicle model. The airflow around the Ahmed body captures the essential flow features around an automobile and was first defined and…

            calendar

            20 Apr 2022 09:25 AM IST

            Read more

            Week 4 - CHT Analysis on Exhaust port

            Objective:

            1.Aim:      Steady state CHT analysis on Exhaust port at an inlet velocity of 5 m/s. 2.Introduction:       Simulate fluid flow and assume that the walls of the container were at a constant temperature or even adiabatic. In reality, however, the heat transfer between solids and surrounding…

            calendar

            21 Apr 2022 07:41 AM IST

            Read more

            Week 5 - Rayleigh Taylor Instability

            Objective:

             1.Aim:  To conduct the Rayleigh Taylor CFD simulation. 2.Introduction The Rayleigh–Taylor instability is an instability of an interface between two fluids of different densities which occurs when the lighter fluid is pushing the heavier fluid. A heavy fluid  supported against gravity by…

            calendar

            23 Apr 2022 04:57 AM IST

            Read more

            Week 6 - CHT Analysis on a Graphics card

            Objective:

            1.Aim: To perform the Conjugate heat transfer analysis on a graphics card. 2.Objectives: Run the simulation by varying the velocity from 1m/sec to 5m/sec for at least 3 velocities and discuss the results. Find out the maximum temperature and heat transfer coefficient attained by the processor. Prove that the simulation…

            calendar

            25 Apr 2022 02:49 PM IST

            Read more

            Week 9 - Parametric study on Gate valve.

            Objective:

            1.Aim: Parametric study for Gate valve.  2.Introduction: The valve has a disc or a gate. The gate has a transverse motion to the direction of fluid flow. Thus, this arrangement either fully stops or opens the passage of fluid. Gate valve finds its application where it is necessary to handle a constant flow of…

            calendar

            27 Apr 2022 06:23 PM IST

            Read more

            Week 8 - Simulating Cyclone separator with Discrete Phase Modelling

            Objective:

            1.Aim: To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop. 2.Introduction: A cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without the use of filters, through vortex separation. When removing particulate matter…

            calendar

            29 Apr 2022 11:54 AM IST

            Read more

            Week 10 - Simulating Combustion of Natural Gas.

            Objective:

            1.Aim: To perform a combustion simulation on the combustor model usig methane as fuel. 2.Theory: Combustion refers to the process where a substance burns in the presence of Oxygen, giving off heat and light in the process. You might have heard that certain substances are combustible whereas some are non-combustible.…

            calendar

            01 May 2022 01:22 PM IST

            Read more

            Week 2 Challenge : Surface meshing on a Pressure valve

            Objective:

            1.Aim: To create a surface meshing on a Pressure valve by using Ansa. 2.Objectives: Set target length and mesh the model.                        Target length = 5mm,3mm,1mm                        Element…

            calendar

            09 May 2022 06:17 AM IST

            Read more

            Week 3 Challenge : CFD meshing on Turbocharger

            Objective:

            1.Aim: To create a CFD mesh on Turbo charger by using Ansa. 2.Objectives: Set target length and mesh the model. Blade stage-1 = 1 mm Blade stage-2 = 1 mm Impeller = 2 mm Shaft rotor = 1 mm Turbo casing = 5 mm Compressor casing = 5 mm Inlet casing cover = 5 mm 3.Procedure: 1.Open an ANSA software and import a Geometry.…

            calendar

            11 May 2022 03:59 AM IST

            Read more

            Week 5 Challenge : Surface wrap on Automotive Assembly

            Objective:

            1.Aim: To create a Surface wrap on Automotive Assembly by using Ansa. 2.Objectives: Target length for Wrap = 3 mm. 3.Procedure: 1.Open an ANSA software and import a Geometry.     Fig: Imported Geometry 2.After Importing geometry, Check the geometry and its shows some error in topology. Checks>Geometry…

            calendar

            12 May 2022 11:01 AM IST

            Read more

            Week 4 Challenge : CFD Meshing for BMW car

            Objective:

            1.Aim: To create a CFD meshing for BMW car by using Ansa. 2.Objectives: Target lengths for the different parts of a model are as follow: Body - 3 mm Lights - 4 mm Grills - 1 mm Rims and Tyres - 2 mm Optical Rear view mirror - 2 mm Window - 2 mm Silencer - 3 mm Logo - 1 mm. 3.Procedure: 1.Open an ANSA software and import…

            calendar

            16 May 2022 03:15 PM IST

            Read more

            Project 1 : CFD Meshing for Tesla Cyber Truck

            Objective:

            1.Aim: To create a CFD meshing for Tesla Cyber Truck by using Ansa. 2.Objectives: Target lengths for the different parts of a model are as follow: Body - 12 mm Tyre and rims - 15mm Windows - 10mm 3.Procedure: 1.Open an ANSA software and import a Geometry. Fig: Imported Geometry 2.After Importing geometry, Check the geometry…

            calendar

            17 May 2022 08:21 AM IST

            Read more

            Week 1 : Exploring the GUI of GT-POWER

            Objective:

            GT-SUITE is the industry-leading simulation tool with capabilities and libraries aimed at a wide variety of applications and industries. It offers engineers functionalities ranging from fast concept design to detailed system or sub-system/component analyses, design optimization and root cause investigation. Why you should…

            calendar

            06 Jun 2022 03:07 PM IST

            Read more

            Week 2 : Basic Calibration of Single cylinder SI-Engine

            Objective:

            Aim: To run the single cylinder SI engine setup at 1800 rpm and list down parameters such as air flow rate,BMEP,BSFC,In-cylinder pressure. To run the same setup at 3600 rpm and to increase the output by 10%  Introduction: SI engine stands for spark ignition engine. Spark ignition engine means any engine in which fuel…

            calendar

            12 Jun 2022 07:19 AM IST

              Read more

              Week-4 : Basic Calibration of Single cylinder CI-Engine

              Objective:

              Aim: Basic Calibration of single cylinder CI-Engine. Objectives: 1.Compare SI vs CI and list down differences (assignment no 2-SI) 2.Comments on following parameters BSFC Exhaust Temperature A/F ratios 3.Change MFB 50 and observe impact on performance Pre-processing and solver: 1.Compare SI vs CI and list down differences…

              calendar

              23 Jun 2022 02:23 PM IST

                Read more
                Showing 1 of 24 projects

                3 Course Certificates

                certificate

                Introduction to CFD using MATLAB and OpenFOAM

                CertificateIcon
                Certificate UID: bqxcrl39hvdzjtsf
                View Certificate
                certificate

                Introduction to GUI based CFD using ANSYS Fluent

                CertificateIcon
                Certificate UID: 2vwgjeo1kz9q456u
                View Certificate
                certificate

                Advanced CFD Meshing using ANSA

                CertificateIcon
                Certificate UID: 39xvji1wfcl8ba2t
                View Certificate
                Showing 1 of 3 certificates

                Academic Qualification

                B.E

                KPR Institute of Engineering and Technology

                01 Aug 2016 - 10 Apr 2020

                12th

                Roever School

                02 Jul 2015 - 31 Mar 2016

                10th

                Aruna Higher Secondary School

                01 Jun 2013 - 15 Apr 2014

                Schedule a counselling session

                Firstname is required
                Lastname is required
                Please enter a valid email
                Please enter a valid number

                Here are the courses that I have enrolled

                coursecard
                4.8

                13 Hours of Content

                coursecard
                4.9

                12 Hours of Content

                coursecard
                Recently launched

                18 Hours of Content

                coursecard
                Recently launched

                21 Hours of Content

                coursecard
                Recently launched

                10 Hours of Content

                Similar Profiles

                Dileep kumar  kurmapu
                Dileep kumar kurmapu

                consistency is the key

                sohan G Naik
                sohan G Naik

                God is Great!

                Kundeti Ganesh
                Kundeti Ganesh

                just do it

                SANJO SEBASTIAN
                SANJO SEBASTIAN

                Choosing the best skills from the rest

                Amol Ramesh Pavitre
                Amol Ramesh Pavitre

                Electrical Engineer

                Try our top engineering courses, projects & workshops today!Book a FREE Demo