Aim of the project To make a Simulink model of Doorbell using a solenoid block with a holding time of 2seconds. To make a Simulink model of a Thermistor sensed temperature of a heater and on-off condition of fan with varying temperature condition. The objective of the project To describe the Simulink model of doorbell…

Aim of the project: - To Implement the control Logic of a “washing machine” using Stateflow. To create a Simulink chart for the “Gear Shift” The objective of the project: - To implement the control logic of a” washing machine “using Stateflow as per the sequences that the system activated…

Aim of the project: -                 To carry out a system level simulation of an All-Terrain Vehicle (AVT) using MATLAB Objective of the project: -                 It is to prepare a technical report explaining the Baja model ATV Properties with the varying conditions Software Used MATLAB R2020a Body of the content:…

1.Travel test For 45km of  EV_default_in file, if cargo mass is 500kg with all other default conditions and FTP drive cycle  is used ADVISOR/Advanced Vehicle Simulator                 Once the ADVISOR is loaded in the MATLAB have to start the…

Week-4 Challenge WOT Condition Part-2 1) a.The difference between the mapped and dynamic model of motor, generator, engine   Mapped Model: - Also known as a static model, runs the simulation based on the data saved on a lookup table. Mapped /Static Model Dynamic Model runs the simulation based on the data saved on…

Week-6 Challenge: EV Drivetrain 1)Type of power converter circuits employed in electric and hybrid vehicles.             A power converter is an electrical circuit that changes the electric energy from one form into the desired form optimized for the specific load.…

1)MATLAB Model of speed control of h bridge controller MATLAB demo model of “speed control of a DC motor using BJT H-Bridge”. The BJT (Bipolar Junction Transistor) when used for power switching applications, operates as an IGBT. when it is conducting (The BJT operates at the saturation region), a forward voltage…

The energy required for Braking for a defined drive cycle Braking: - Braking is the process of applying force to stop or slow down a vehicle. A commonly used technique to break a vehicle is applying friction. Braking consumes energy it is the same as that the kinetic energy should apply for accelerating the vehicle. The…

Design of an Electric Vehicle Aim of the project                 To Create a MATLAB model of an Electrical car that uses a battery and a DC Motor.  Objectives of the project                …

Aim : - To develop  MATLAB Simulink model of Vehicle Direction Indicator Requirement - 1: Steering wheel input as yaw rate (Signal name: SteeringWheel_YawDegreeInput) is the input for this system. This is compared against 3 angular values, one each for left turn, right turn & straight drive (Calibration Values: Right_Turn_AngularLimit,…

Aim of the project                 To create a MATLAB model, Model advisor Check report and Code generation of Traffic_Jam_Assistant Feature based on the requirement Objective of the project                …

Adaptive Cruise Control Aim of the Project: -                 To create a MATLAB model of Adaptive cruise control of a vehicle. The objective of the project: - Developing Adaptive Cruise Control feature as per the requirement document using MATLAB…

  Highway Assistant – Lane Changing Assistant Aim of the Project: - To develop one specific requirement of Highway Assistant – Lane Changing Assistant algorithm to familiarize with concepts of Autosar Software Component Development in MATLAB Environment by following the Model Based Development guidelines.…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells. Give your detailed explanation on it. Answer:-  Battery is an electrochemical device to provide electrical power, which converts chemical energy in to…

https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation…

  Aim: -                 To Prepare a detailed battery pack drawing along with its enclosure, with a battery pack capacity of 18kWh using the cell model ANR26650M1-B Battery and Battery Pack: - Batteries are made up of one or more cells whose…