Project 2 Adaptive Cruise Control

  Aim: -                 To Prepare a detailed battery pack drawing along with its enclosure, with a battery pack capacity of 18kWh using the cell model ANR26650M1-B Battery and Battery Pack: - Batteries are made up of one or more cells whose…

https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells. Give your detailed explanation on it. Answer:-  Battery is an electrochemical device to provide electrical power, which converts chemical energy in to…

  Highway Assistant – Lane Changing Assistant Aim of the Project: - To develop one specific requirement of Highway Assistant – Lane Changing Assistant algorithm to familiarize with concepts of Autosar Software Component Development in MATLAB Environment by following the Model Based Development guidelines.…

Adaptive Cruise Control Aim of the Project: -                 To create a MATLAB model of Adaptive cruise control of a vehicle. The objective of the project: - Developing Adaptive Cruise Control feature as per the requirement document using MATLAB…

Aim of the project                 To create a MATLAB model, Model advisor Check report and Code generation of Traffic_Jam_Assistant Feature based on the requirement Objective of the project                …

Aim : - To develop  MATLAB Simulink model of Vehicle Direction Indicator Requirement - 1: Steering wheel input as yaw rate (Signal name: SteeringWheel_YawDegreeInput) is the input for this system. This is compared against 3 angular values, one each for left turn, right turn & straight drive (Calibration Values: Right_Turn_AngularLimit,…

Design of an Electric Vehicle Aim of the project                 To Create a MATLAB model of an Electrical car that uses a battery and a DC Motor.  Objectives of the project                …

The energy required for Braking for a defined drive cycle Braking: - Braking is the process of applying force to stop or slow down a vehicle. A commonly used technique to break a vehicle is applying friction. Braking consumes energy it is the same as that the kinetic energy should apply for accelerating the vehicle. The…

1)MATLAB Model of speed control of h bridge controller MATLAB demo model of “speed control of a DC motor using BJT H-Bridge”. The BJT (Bipolar Junction Transistor) when used for power switching applications, operates as an IGBT. when it is conducting (The BJT operates at the saturation region), a forward voltage…

Week-6 Challenge: EV Drivetrain 1)Type of power converter circuits employed in electric and hybrid vehicles.             A power converter is an electrical circuit that changes the electric energy from one form into the desired form optimized for the specific load.…

Week-4 Challenge WOT Condition Part-2 1) a.The difference between the mapped and dynamic model of motor, generator, engine   Mapped Model: - Also known as a static model, runs the simulation based on the data saved on a lookup table. Mapped /Static Model Dynamic Model runs the simulation based on the data saved on…

1.Travel test For 45km of  EV_default_in file, if cargo mass is 500kg with all other default conditions and FTP drive cycle  is used ADVISOR/Advanced Vehicle Simulator                 Once the ADVISOR is loaded in the MATLAB have to start the…

Aim of the project: -                 To carry out a system level simulation of an All-Terrain Vehicle (AVT) using MATLAB Objective of the project: -                 It is to prepare a technical report explaining the Baja model ATV Properties with the varying conditions Software Used MATLAB R2020a Body of the content:…

Aim of the project: - To Implement the control Logic of a “washing machine” using Stateflow. To create a Simulink chart for the “Gear Shift” The objective of the project: - To implement the control logic of a” washing machine “using Stateflow as per the sequences that the system activated…

Aim of the project To make a Simulink model of Doorbell using a solenoid block with a holding time of 2seconds. To make a Simulink model of a Thermistor sensed temperature of a heater and on-off condition of fan with varying temperature condition. The objective of the project To describe the Simulink model of doorbell…