Aim - To write a program in matlab to simulate the forward kinematics of a 2R Robotic arm Objective - To write a program to simulate forward kinematics of a 2R robotic arm.to create a animation /movie from the plots obtained from the programing.CODE Explanation-starting the program using the comments.providing…

AIM -:  TO create a animation of simple pendulum by using socond order differential equation by ODE solver fuction.  To create a plot angular velocity and displacement of simple pendulum by ode45.    Equation of simple pendulum               b= damping coefficient…

GENETIC ALGORITHM - The genetic algorithm is a method for solving both constrained and unconstrained optimization problems that is based on natural selection, the process that drives biological evolution. The genetic algorithm repeatedly modifies a population of individual solutions. At each step, the genetic algorithm…

AIM:- Creation of rankine cycle simulator from given input and reading tha data from standard thermodynamic library of steam table. OBJECTIVE:- To plot the T-s and H-S curve for given input in Rankine cycle. To get the output in command window for each state point in the cycle. To calculate the state point using function…

 BENCHMARKING:-  Benchmarking is defined as the process of measuring products, services, and processes against those of organizations known to be leaders in one or more aspects of their operations. Benchmarking provides necessary insights to help you understand how your organization compares with similar organizations,…

UNDERBODY COATING:- Undercoating coating is usually a dense cladding applied uniformly to the unercarriage of the automobile .it is normally sprayed or painted on when the car is just out of the dealership and is clean .but even if you are getting the undercoating applied after a couple of years ,it s fine too. this is…

 HOOD The hood is hinged cover over the engine of motor vechile .hoods can be open to allow access to the engine compartment or trunk on rear engine and some mid engine vechile for maintinance and repair. the inner panel is provide the strength and support where the outer panel is a metal cover that has…

FENDER :- Fender is the american english term for the part of an automobile ,motorcycle,or other vechile body that frames a wheel well .it is a part that is in contact with the different parts of the vechilelike the A-pillar .sill mount,drip mount,body mount,bumper mount.typically fenders are rigid and house the wheels…

Wheel arch area : It is a curved part of the fender positioned right above the wheel. The wheel arch is designed such that it protects both the pedestrain and car cabin from mud water rocks and other road spray. Different countries have different wheel arch regulations in place ,and the wheel arch design has to comply…

SECTION MODULUS : IT is a way of quantifying a cross section of a given geometry.it is directly proportional to the area moment of inertia of the cross section.higher the section modulus,the more moment of inertia,more stiffness and thus more resistance to deformation and bending.section modulus can be improved by varying…

ROOF DESIGN Objective  The objective this challenge design car roof with essential flanges and reinforcement  like ditch area front roof rai,bow roof,cntre roof railand rear roof railfor the given styling surface Perform a curvature study on the roof and perform the calculation for the heat distortion and snow…

AIM - To design car back door panel from given surface A data under design rules regulation. BACK DOOR ASEEMBLY Inner panel outer panel upper  outer panel lower hinge and reinforcement wiper motoe reinforcement latch and striker its reinforcement gas stay reinforcement OUTER PANEL - 0.75mm INNER PANEL - 0.75mm REINFORCEMENT…

    AIM - Design Base Bracket Plastic component through the given Class- A SURFACE    Design Procedure :  Creating tooling Axis In class- A To perform draft analysis To create B surface To create C surface To create solid part      Creating a tooling axis in Class - A Surface The…

The aim of this project is to develop the product design of the switch bezel with the help of the class A surface following the OEM standards. Introduction Class A Class A surface is the term mainly used in automotive design industry. It describes the final production surface data for the aesthetic parts of the car.…

AIM : To create a Coin Holder plastic component through the given Class A surface and perfoming the draft analysis on the model objectives : To ensure proper tree structure is followed To keep the design as per requirement All the sketches should be iso constrained To publish the Class A,B and C Surface. Tooling…

AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A surface…

AIM: To Create DOOR trim with thickness of 2.5 with 3 degree draft angle.  we have to create the required Tooling-Axis for the given Class A Surface while meeting the requirements of the necessary Draft Angle & then perform the Draft-Analysis Operation on the Class A Surface itself.…

Core & Cavity Design Aim: To create the Core and cavity blocks for the Switch Bezel Component. DRAFT ANALYSIS ON SWITCH BEZEL COMPONENT: The surface should be green and in the column nominal value 3deg given as input. hence the draft analysis on the switch bezel is successfully performed. Parting surface: During…

OBJECTIVE:CREATE THE PLASTIC PRODUCT FROM THE CLASS A SURFACE GIVEN.AND CREATE THE RIB AND SCRRE BOSSES AS PER THE DESIGN CONSIDERATION. Tooling Axis: To create the tooling axis, I extracted the surface of class A with no propagation and I created the point at the centre of the extracted surface and created a line at that…

AIM: CREATE THE DOGHOUSE ON COIN HOLDER. Create the Dog House for the Door Trim considering the design rules. "C" is where the doghouse contacts the backside of the surface  Doghouse wall thickness at the intersection of the part wall ( C ) should be 40% or less than the main wall stock ( T ).  The height of …

DOOR TRIM LOWER WITH ENGINEERING FEATURES (HEAT STAKES AND LOCATORS) Aim: To design a solid body from the given class A surfaces by creating tooling axis, B and C surface  then do the draft analysis for the same then conclude the result by adding engineering features like heat stakes and the locators. Objectives: • Creation…

AIM:     Create the Pillar, Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  TOOLING AXIS Now we create tooling axis for…

Project Tiltle : ASSEMBLY WORKBENCH 1) Quick Return Mechanism : Part modeling :- PART 1 PART 2   PART 3   PART 4 FINAL ASSEMBLY  2ND ASSEMBLY PART MODEL PART 1 PART 2 PART 3 FINAL ASSEMBLY  

AIM: To design the car door inner panel with reference to given Class-A surface by using given mastersection, creating attachment features and performing draft analysis to check the manufacturing feasibility of the component by using software CATIA V5. Methodology: The methodology of the project is explained here:1. Class-A…

Title of the Project:  CASING DESIGN Objective: Design the Casing in sheet metal using NX Cad. Description of Tools: TAB is the command to create a base feature by extruding a sketch alo0ng a vector bt a thickness values or by adding material to existing faces and bend regions of a sheet metal parts.…

BOX ASSEMBLY OBJECTIVE: To observe the model and design the sheet metal by using given dimensions and instructions  INTRODUCTION: NX is widely used Computer Aided Designing software for multi purposes like designing, engineering and manufacturing. It used in various fields for different works. Using different features…

DESIGNING A SHEET METAL BRACKET OBJECTIVE The objective of the project is to design a sheet metal Bracket using sheet metal application in Siemens NX software along with a detailed drawing sheet. DESIGN METHODOLOGY FEATURES USED FOR MODELLING TAB – Creates a base feature by extruding a sketch along a vector by a thickness…

Title of the Project:  CASING DESIGN Objective: Design the Casing in sheet metal using NX Cad. Description of Tools: TAB is the command to create a base feature by extruding a sketch alo0ng a vector bt a thickness values or by adding material to existing faces and bend regions of a sheet metal parts.…

Objective: The main objective of this project is to design a sheet metal BRACKET II in NX cad sheet metal application workbench. Also, to perform the drafting for the bracket part. Sheet metal Design and Fabrication:- # NX sheet metal design software includes material and…