now, we are going to slove the second order ODE in the first step the basic program should be type in the editor windoe  and then the input are fed in the program is called geomentry parameters.like, mass, length, damping, gravity. Ater that the initial condition should be fed into the editor window the displacement…

A GENETRIC ALGORITHM                                       A GENETRIC ALGORITHM IS A METHOD TO SLOVE THE BOTH CONSTRAINED AND UNCONSTRAINED  OPTIMIZATION PROBLEM BASED ON A NATURAL SELECTION PROCESS THAT MIMICS BIOLOGICAL…

\                     AIM  Create the tooling axis for the given Fan cover model meeting the requirements of the draft angle and perform the Draft analysis on the model. PROCEDURE  construction of xz axis  First step  check the given fan cover modeling …

                                                       the first step is to determine the tooling axis for the given centre console coin holder of the class A surface  In the…

                                                                                           …

                                             AIM:        To create a rib for coin console considering the design rule for the ribs CONSTRUCTION         The first step…

AIM:  To determine  the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  PROCEDURE: The First method in this…

AIM   To determine the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.   PROCEDURE:   To create the…

AIM  To Create the boss and Dog House for the Centre console coin holder considering the design rules General Guidelines for Bosses SCREW BOSS  Boss design in plastic parts should be as per guidelines to ensure boss strength and avoid injection molding defects. Recommended boss wall thickness…

DOORTRIM FINAL PROJECT  ARM REST  In the final project the input they gave the class A suface and master section for the  flanges in this project  they gave four bodies of the door trim of the project.They are  ARM REST  LOWER SUBSTRATE  MAP POCKET  BOTTLE HOLDER  In this project…

    Door Applique Design AIM   To Create the Door Applique Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create…

AIM To develop Class A surface input provided into a product design following the OEM design standards using CATIA V5 Surfaceworkbench and to ensure that the product is manufacturable by injection molding.   OBJECTIVE  The project report deals with the steps and procedures followed while creating a Door arm rest…

QUESTION  1. Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, five-year-old boy, his father, and his mother. He visits his native place…

  AIM: To Design B-Pillar Through Master Section Development And Write a Detailed Report. Given: A-Surface Master Sections Distance Between Ribs Should Be 50mm  B-Pillar The B-Pillar Is The Central Pillar Of The Car. This Pillar Is Actually a Sheet Metal Part Which Is Welded In The Biw Of The Car. The B-Pillar…

 Objective: To create quick return mechanism and CV joint parts in part workbench or generative work bench and assemble themfollowing guidelines   CV JOINT  2. CV JOINTConstant-velocity joints (also known as homokinetic or CV joints) allow a drive shaft to transmit power through a variable angle, atconstant…

  AIM  Use the Section from your Hood design and calculate the section modulus using the formula S = I/y S = Section Modulus I = Moment of Inertia y = distance between the neutral axis and the extreme end of the object  SECTION MODULUS section modulus is use for the analysis purpose. To measure the strength of the hood…

Under Body Coating Under seal (often called undercoating in the U.S.) is a thick resilient coating applied to the underbody or chassis of an automobile toprotect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin. Historically a bitumen-based compound was used, but…

AIM Design Hood outer panel, inner panel and the necessary reinforcements by following the Master section mentioned with the design parameter explained in the videos. Submit an assembly of Hood inner panel, outer panel, latch, hinge and the reinforcementsA detailed report about the Hood Design which includes a detailed…

 FENDER DESIGN Objective : The main object of this project is to design the BIW(Body in white) of front fender using the fender skin data and master section as the into data by using CATIA V5 Introduction :Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames…

Objective: Use the provided styling surface to come up with a back door design, use appropriate design methodologies and provide thenecessary reinforcements and embosses. Software Used:catia v5  Backdoor Introduction:An automobile back door or Tailgate is the panel that covers the boot (or trunk) of an automobile.…

   AIM  For the given Car Roof styling, design and develop the essential flanges and reinforcements, Are in the outer panel, Front Roof Rail,Rear Roof Rail, Centre Roof Rail and FR and RR Bow-Roofs.  Do a curvature study on the roof and perform calculations for Heat Distortion and Snow load criterion to determine and justify…

AIM: To Calculate the Wheel Arc area and prove whether the car will pass the standards  WHEEL ARC:  Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The main intention for the calculation of wheel arc radius is to position the wheel inside the fender body, because…

AIM  Assemble and apply GD&T to the butterfly valve assembly drawing   ASSEMBLY  After modeling all the individual parts of the butterfly valve, all parts are assembled together in the assembly workbench of NX     GD&T  DIMENSION