Aim : Code to perform curve fitting in linear polynomial fit splitwise method using matlab. Objective : To code curve fitting for specific heat and temperature datas,in linear polynomial fit .And to obtain the plot for predicting the data set.     clear all close allclc % inputs datas of specific heat and Temperature…

Aim : To code the simple pendulum that will simulate the pendulum motion using Sceond order ODEs. Objective : Write a program that will simulate the pendulum motion and to animate plot for simple Pendulum using second order ODEs.   close all clear allclc % inputs b = 0.05;g = 9.81;m = 0.1;l = 1; % inputs for…

Aim : A code to optimise the stalagmite function and find the global maxima of the function. Objective : To a Write a program for  optimising the stalagmite function and find the global maxima of the function. clear allclose allclc % inputs x = linspace (0,0.6,150);y = linspace(0,0.6,150);[xx…

Aim : To Code a function that extracts the 14 co-efficients  using  NASA Thermodynamic data. Objective :  To wirte a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. Using the LOCAL TEMPERATURE…

Aim: To mesh the given component with the Size of 5 Units .And to  Create 1D elements of  Rod,Beam ,Bar elements. Objective :  To mesh the given component ,apply the mass of magnitude 10 with the RBE2 link and to  Join the two components with Spring elements  .And…

Aim : To extract the middle surface and to mesh the given component. Objective: To extract the middle surface and to mesh with mixed and the mesh elements are of 5 for  given component. Given Component : * The above shown are the given component. *Importing the geometry file  * Go to menu bar and click import geometry…

Aim : To perform tetramesh of given models . Objective :To perform tetramesh from 2D to 3D Conversion or by Quick Tetra Mesh/ Volume Tetra Mesh under give mesh parameters. * Given models are shown below; * Importing the geometry ; * clicking to task bar and to import geomerty ,selecting the model according to file type…

Aim : To mesh the given geometry and to acheive the given mesh parameters Objective : To mesh the given model and Creation of 1D Connectors to given geometry,moreover to perform mesh withgiven parameters. * Given Model : * The Above shown are given model * Importing the given model : * The given model are in hypermesh…

Aim : To perform Meshing of a Door Inner Panel ,with given mesh parameter and to extract the given side door. Objective : to mesh the given side door model as given in above mesh creteria ,and to perform extraction of model . * Given model : * Opening the model  * Click to open model as shown below  * After Opening the…

Aim : To extract and to mesh the given geometry. Objective : To mesh and to extract the give model in given geometry parameters. moreover to assign the thickness. Given Model : Opening the given geometry : * Click to open geometry in task bar. * And click Open  as shown below fig. * Extraction of mid surface …

Aim : To clean and mesh the given geometry ,in given parameters. Objective :To perform  the geometry cleanup operation on the given files,Clean the geometry,furthermore to Extract midsurface,Clean midsurface geometry ,Ignore holes less than dia 5mm.Create 2D mesh with target length 5mm, min 3.5mm max 7mm and…

* Answers for above mentioned questions : 1. Check the material properties of the rail component and calculate the speed of sound in steel rail=___3.67m/s____  I.e, * Given formula to calculate are mentioned below :  Elemental time step  * delta Tc = l/c             …

Aim : To Perform stimulation of given shell geomerty for given material property. Objective: To stimulate the given geometry with normal stimulation and to stimulate for above given material property are * Opening user profile : * Importing the file : * From browser click import solver deck   * selecting…

The Report is attached below.

the file is attached below

The file is attached below 

the file is attched below 

the File are attched below 

the file is attached below 

the files are attached below 

The Model and PPT are attached below .

the file is attched below 

THe files are attached below 

the files are attched below .

the file is attached below

the file is attched below .

li*                         Week 7: Report on Assembly of Chopper Model.  Objective : To perform the assembly, for designed chopper parts . Introduction: Performing assembly ,for designed parts like ,chassis, engine ,chain,kick stand , front and rear…

 1. Radar Mast  Trees. *Front View : *Left View: *Right view : *Top view: *Isometric View : * The files are attched below.    2. Yacht Assembly  * Aim : Assembly of  Yacht Modelling. * Objective : Performing of assemblies for designed Hull,garage door,front ,middel and rear seats…

Title : Report on Sheet Metal Component. Objective : A detailed report on Sheet Metal Component and about  Sheet Metal modelling tools applied throughout the modelling. Introduction : Start the NX and Open a new file for creating a sheet metal ,giving the dimension as required for casing .Giving the flanges,punch.…

* Title : Report on Sheet metal component . * Objective : To Design a sheet metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling. And to attach the images as required . * Introduction : Open NX and create a rectangular sketch ,genearate a solid model…

* Title : Report on Sheet Metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling. *Objective : Detailed report on Sheet Metal Odd Shaped Enclosure. And with a good explanation on Sheet Metal modelling tools applied throughout the modelling. * Introduction : …

* Title : Report on Sheet Metal Component with good explanation on Sheet Metal modelling of Sheet Metal Bracket. * Objective : To Write a detailed report on Sheet Metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling.And to attach the different views images  of…

* Title : Report on Sheet Metal bracket. * Objective : To perform a detailed report on Sheet Metal Component with good explanation of Sheet Metal Bracket.And on the  Sheet Metal modelling tools applied throughout the modelling. * Introduction :  * Open NX cad and start with new. * Now,sketching…

The PP T is attached below  

The PPt is attached below

The files are attached below .