Aim :- to create cs of looad bearing wall                over the spread footing      procedure : first create a spread footing of 0.90 width and 0.25 height                       by rectangular…

   aim :- to create the diferent shapes by using decimal ,engineering            architectural . procedure :- primarily select the decimal or engineering or architectural in which u                       want to do then…

    aim :- to sketch the layout of a residence  procedure :- by using the xl option and offset draw the outer wall of 9'' of length 12'6'' in x direction                     and 43'6.5'' in y direction and trim the extra portions , and then draw the…

1.               2             3           4               5  

1             2           3      

AIM TO CREATE THE ARCHITECTURAL DRAWING AND STRUCTURAL DRAWWINGS       FOR GIVEN PLOT SIZE  create the floor plan using the given plot size by using various tools xl  line  limax setup circles arc hatching etc tools create the layout ie floor plan  then create sections accroding…

1.   GO to the file menu click on new then it asks about the chooseing template  then select template and give ok then it opens the new file and from file save by giving required name to it.         2.close  the save file as shown . and to open given fig below in recent models open…

1 ans :- BIM is a visual representation of physical and functional characteristics of facility            from inception , as such it serves as shared information for collaboration throught a facilities            life cycle.         …

1 ans:-  aim  and introduction ;- to create the floor for week 2 plan layout  go to the roof tab under the architectural   select the floor architecture              then from the propety browser select required structure and length      select…

1 ans :- aim- to create the ceiling above the walls at first floor level   go to the architectural tab click on the ceiling        then the another tab opens click on the sketch celing          then select pick points choose outer line of the layout then tick on green mark…

 1 ans :- Building codes or standards essential for modelling or efficiency of                drawings in revit are             * A set of standards that are uniform to all structures in the modelling process          …

1 ans :- AIM - to set the shared coordinates and project base point                       from the architectural template    First open the new project as architectural template then  save it by giving some name as architectural .   then go…

1. aim - to create the structure of a school building   open the new file of  architectural template  create levels of required footing , first floor and second floor in the elevations  using the architectural template create walls in the ground floor up to first floor level       …

1. HVAC (heating ventillation and air conditioning )       it is a technology of indoor environment comfort , its goal is       to provide the thermal comfort and accepable indoor air        quality . its the important part of the structure * as a examples helps…

1 aim :- By using short cut keys in revit complete the tasks     1. section box  - BX    To make the section box click the component  and type BX   section box is created for ex-     2. create similar - CS select component> type CS> similar component is crteated and…

DYNAMO    1ANS :-     AIM -To create the sinusoidal points and create the curve and create the surface               for the points and lines created                INTRODUCTION - creating the aim using the dynamo  …

1 ANS :-  1a) .   In the fig 1a seen clearly then identified here is- the rupture occoured as the concrete spalled beyound the         reinforcement  , reinforcemnt is seen / visible and the concrete is crushed , top portion of beam looks safe because of flange advantage …

1 solution:-  lateral stiffness of one storey frame-             -  the structure can be analyzed by any of the standard methods including moment distribution method ,              here we use the definition of stiffness influence coefiicients to solve               -  thus the 3*3 stiffnss matrix of the structure is known…

 solution -     finally obtained the base shear 

1 ans : SYMMETRY- when we have a look over the aspect of symmetry of the framing plan , it is observed that the distribution of mass,stiffness is across the plan it is considered as one of the good symmetrical aspects . this tends to reduce the horizontal displacements in both of the two orthogonal horizontal directions…

1ans :As the structure is more restrained it will be more shrinking, expanding and cracking.                                                            there will be more floor shrinkage and expanding in structure A whereas there will be minimum cracks in structure B              and C .           The shear walls in the…

AIM- To create 25 storey buildings using etabs with given details in question.   Go to file open the new modal > model initialization tab occurs fill it and click ok   then the new model quick template tab opens  in which select custom grid spacing and custom story data after that go to edit grid data…

aim - Design a square footing for a column size of 400x400 and check for give details    procedure -to design the square footing the steps involved in footing are 1 calculation of gross soil pressure for footing area  2 calculation of net soil pressure for flexural and shear design  3 initial depth…