(CLASS A SURFACE) (FINAL BODY WITHOUT RIBS AND SCREW BOSSES)(COMPONENT WITH RIBS AND SCREW BOSSES VIEW-1)(COMPONENT WITH RIBS AND SCREW BOSSES VIEW-2)

(DRAFT ANALYSIS REPORT)(DRAFT ANALYSIS FOR CLASS A SURFACE)(DRAFT ANALYSIS FOR FINAL BODY)(THICKNESS MEASUREMENTS AT SOME RANDOM AND CRITICAL POINTS)(VARIOUS VIEWS OF FINAL COMPONENT)(TREE STRUCTURE SNIPS)

REPORT-BUMPER                 TOOLING AXIS CREATION: The given Class-A surface i. e Bumper is free of pocket-shaped features like bins and perpendicular walls, although short tall curvy surfaces are present at the end, it was already maintained with enough draft, hence guessing the…

 THE DOG HOUSES CREATED ARE GIVEN 1.5 DEGREE DRAFT FOR SURFACES CLEARING IN MAIN AXIS AND SEPARATELY 1.5 DEGREE FOR SURFACES CLEARING IN SIDE CORE TOOLING AXIS. 

(DRAFT ANALYSIS-CLASS A SURFACE)(DRAFT ANAYSIS- FINAL BODY WITHOUT ATTACHMENT FEATURES)(DRAFT ANALYSIS- FINAL BODY ALONG WITH HEAT STAKES AND LOCATORS)

                                                                                           …

                                                                                           …

Defining Connector 1 The given connector is Being Defined in Electrical Part Design Workbench. The details are listed below: 3 points and 2 axis systems are being created, 1 for connector connection provision. 2for bundle entry provision. 3 for Mounting clip provision, Firstly, the connector connection point is defined,…

REPORT Defining P Clamp. The following steps are being followed: The given CAD file is downloaded and opened in CATIAV5 Software While defining the P Clamp, 2 entry sides and a base should be given Using part design workbench the points at the 2 sides are created using centre of circle definition Planes parallel to their…

                                           Report The aim was to route the harness as per the given diagram and to add protective coverings. Firstly, the require connectors .stp file is being downloaded from the…

REPORT   Aim : To route the harness layout in given format using Electrical workbench.   Also, To Check Bundle Continuity. Add Annotation wherever necessary. To check for the Bundle warning. To generate .CATPart from .CATProduct To Convert it in .igs format.   First Step Download all necessary connector…

REPORT Aim: To Flatten previously made wire harness assembly using the CATIA Electrical Harness Flattening Workbench following the same layout provided and also to place the same in Drawing sheet.   Step_1: Creating a new product file and enter the Electrical Harness Flattening Workbench. Save it in the same folder…

                                                                                           …

                                                                               REPORT   American Chopper Modeling and…

Link : Sanjay_A_GOOGLE DRIVE Access Link for yatch assembly/ part zip file:             >>>REPORT<<<   >Predator Yatch Modeling and Rendering in SOLIDWORKS<   To begin with, It should be understood by any engineer that the complete development…

TABLE OF CONTENT: A. OBJECTIVES B. DEFINITIONS C. MANUFACTURING PROCESSES 1. HEMMING 2. FORMING (EMBOSS CREATION) D. DESIGN CONSIDERATIONS E. COMMANDS USED IN SIEMENS NX CAD F. DESIGNING USING THE SIEMENS NX TOOL (STEPS, SNIPS, AND RESULTS) G. CONCLUSION   A. OBJECTIVE The aim of this project is to Design a hood assembly…

Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. There are two types of section moduli, the elastic section modulus and the plastic section modulus. Section modulus is the ratio of moment of inertia about neutral axis upon the farthest point of…

A. FENDER:   Fender is the body that frames a wheels well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road-spray from being thrown into the air by the rotating tire. Fenders are typically rigid and can be damaged by contact with the road…

TABLE OF CONTENT: OBJECTIVES DEFINITIONS MANUFACTURING PROCESS DESIGN CONSIDERATIONS DESIGNING USING SIEMENS NX TOOL (STEPS, SNIPS, AND RESULTS) CONCLUSION       OBJECTIVE:   To design a  Front Fender of a car by following the given master section and applying engineering features as per the design…

TABLE OF CONTENT:   OBJECTIVES & INTRODUCTION DESIGN CONSIDERATIONS DFMEA MANUFACTURING PROCESS DESIGNING USING THE SIEMENS NX TOOL CALCULATIONS AND RESULTS CONCLUSION     OBJECTIVE:   The objective of the project is to create the Car Roof, which includes creating engineering features like Front…

  TABLE OF CONTENT: OBJECTIVES & INTRODUCTION DESIGN CONSIDERATIONS MANUFACTURING PROCESS DESIGNING USING THE SIEMENS NX TOOL DRAFT ANALYSIS CONCLUSION OBJECTIVE & INTRODUCTION   OBJECTIVE: Using the provided styling surface to come up with a back door design and  using appropriate design methodologies and make the necessary…

BUTTERFLY VALVE Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and hurt the sealing properties. They are…