i am started the mold design process with following steps :- 1. Draft analysis :- In this i have check the draft of the part with minimum draft angle 0.5. 2. scale :- As mention in the challenge discription i assume the material as ABS. which have shrinkage of 0.6 so i used to take scale of 1.006(as scale…

      There are the steps which is followed by me to create a mold blocks and sliders for the given geometry:- Draft analysis:- For the given geometry first we have to check the draft on the vertical walls so the mold blocks can easily separate from the part. For draft analysis from mold design go through…

      There are the steps which is followed by me to create a mold blocks and sliders for the given geometry:- Draft analysis:- For the given geometry first we have to check the draft on the vertical walls so the mold blocks can easily separate from the part. For draft analysis from mold design go through…

      There are the steps which is followed by me to create a mold blocks and sliders for the given geometry:- Draft analysis: - For the given geometry first we have to check the draft on the vertical walls so the mold blocks can easily separate from the part. For draft analysis from mold design go through…

What is BIW & define its parts? Body in white (BIW) refers to the welded sheet metal component which for the vehicle structure to which the other components will be married, i.e. engine, chassis, exterior & interior trim. BIW refers to the stage in the automobile manufacturing in which a car body’s components…

what is the process of project education activity?   The process of project education activity involves series of steps as discussed below. RFQ received: - Request for Quotation is the first and foremost step involved in project execution. In this type, the customer quotes his requirements, specification, technical…

    There are the steps which is followed by me to create a mold blocks and sliders for the given geometry:- Draft analysis: - For the given geometry first we have to check the draft on the vertical walls so the mold blocks can easily separate from the part. For draft analysis from mold design go through draft…

What is Design Methodology? Design methodology is the steps that is needed to be followed during the concept stage of design. Purchase order: - It is the first official document that we will receive from customer side, this document will basically give confirmation to us that the customer has agreed to our deal and we…

    These are the following steps, which I followed to make this fixture design:- I created a part tree which parts I want to design this fixture. Like for fixed pin design we want a pin , pin retainer , shims, riser, block, and so on Second, I created a circular pin for fix pin unit and created a pin retainer.…

      These are the following steps, which I followed to make this fixture design:- I created a part tree which parts I want to design this fixture. Like for fixed pin design we want a pin , pin retainer , shims, riser, block, and so on Second, I created a circular pin for fix pin unit and created a pin…

      These are the following steps, which I followed to make this fixture design:- I created a part tree which parts I want to design this fixture. Like for fixed pin design we want a pin , pin retainer , shims, riser, block, and so on Second, I created a circular pin for fix pin unit and created a pin…

Q-1       What is the base unit what are the typical types of the base unit? A base unit is the unit designed to mount all the other units of the tool, also other parts necessary for a tool like pneumatic valve box, trunking cable path will also be mounted on to a base unit. Below are the…

        These are the following steps, which I followed to make this fixture design:- I created a part tree which parts I want to design this fixture. Like for fixed pin design we want a pin , pin retainer , shims, riser, block, and so on Second, I created a circular pin for fix pin unit and created…

Q-1 WHAT DO YOU UNDERSTAND BY 3D FINISH PROCESS? 3D finish is the process where design is being completely finish & to be ready for final simulation & 2D detailing. While finishing the design the nominality of holes is checked which ensures the easy assembly of all the units. The hole concentricity & holes…

These are the following steps, which I followed to make this fixture design:- I created a part tree which parts I want to design this fixture. Like for fixed pin design we want a pin , pin retainer , shims, riser, block, and so on Second, I created a circular pin for fix pin unit and created a pin retainer. Then I created…

Q-1 WHAT ARE THE DRAWING TEMPLATES? DRAWING ( AGRAPHICAL REPRESENTATIO): If compared with verbal or written description, drawing offer far better idea about the shape, size & appearance of any object or simulation or location, that too in quite a less time. Hence it has become the best media of communication not only…

BILL OF MATERIAL : -  Quantity Part Number 1 58311_491L0_A_s 1 58313_491L0_s 1 58314_491L0_s 1 58348_491L0_s 1 58349_491L0_s 1 P01_Z01_ST010_01_01.1_BASE_PLATE 2 P01_Z01_ST010_01_01.2_SQ_100*100*2*1400 1 P01_Z01_ST010_01_01.2.1_SQ_100*100*2*1250 2 P01_Z01_ST010_01_01.3_SQ_100*100*2*1900 1 P01_Z01_ST010_01_01.4_PLATE_1…

DRAFT ANALYSIS: - Report on the draft analysis of the fan cover. In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so many…

DRAFT ANALYSIS: -   REPORT: - Report on the draft analysis of the fan cover In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means…

REPORT: - In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so many features and slots are available in the feature because…

  Report on the coin holder. In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so many features and slots are available…

Report on the switch bezel: - In first step, we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so many features and slots are available…

  Report on the coin holder. 1. Surface draft analysis: - In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so many…

Report on the coin holder. 1. Draft analysis on the class A surface In first step we have to check the connectivity of the class-A surface. It means there should be no present gaps between two surfaces. It is fully connected class-A surface. The next step is to find a tooling axis of the class-A. It means there are so…

Draft analysis on the class A surface: - First we want to create a tooling axis which is our first requirement. For that we have different methods from which we perform a draft analysis method. Because the second method is bisecting line method but don’t have any line which can use for the bisecting a line and also…

Model 1  Body 1 Create a circle of the given diameter and then pad it. Create a second circle on the perpendicular plane to the first one and then  pad it in different body. Now using boolean operation add them together. Give a fillet. Body 2 First create a sketch of the base and create a surface of that. Now…

TITLE : - NX_CASING_BEREKAR_MAHENDRA OBJECTIVE :- THIS CASING MODEL IS USED FOR THE COVER A PARTICULAR PART FROM THE DUST OR DIRECT CONTACT WITH ENVIRONMENT. AND ALSO WITH DESIGN OF THIS CASING I LEARNED MORE THINGS ABOUT THE NX CAD. INTRODUCTION : - I USED A DIFFERENT FEATURES TO DESIGN THIS CASING IN NX CAD. LIKE VISE…

TITLE : - NX_BOX_ASSEMBLY_BEREKAR_MAHENDRA OBJECTIVE : - THIS BOX ASSEMBLY IS USE TO CONTAIN THE GOODS AND CARRY THEM FROM ONE PLACE TO ANOTHER PLACE. AND ALSO WITH DESIGN OF THIS CASING I LEARNED MORE THINGS ABOUT THE NX CAD. INTRODUCTION : - I USED DIFFERENT FEATURES TO DESIGN THIS ASSEMBLY IN NX CAD. LIKE I USED…

TITLE :- NX_ODD_ENCLOSURE_BEREKAR_MAHENDRA OBJECTIVE: - THIS ODD ENCLOSURE EXERCISE IS THE GOOD FOR UNDERSTANDING THE CONVERT TO SHEET METAL FEATURE. INTRODUCTION: - IN THIS EXERCISE, WE HAVE TO CONVERT SOLID BODY INTO A SHEET METAL. FOR THAT WE CAN USE CONVERT TO SHEET METAL FEATURE AND USING THIS FEATURE WE CAN WRAP…

TITLE: - NX_BRACKET_BEREKAR_MAHENDRA OBJECTIVE: - THIS BRACKET EXERCISE IS GOOD FOR UNDERSTANDING THE NX SOFTWARE FEATURE VERY BRIFLY LIKE BEAD, COUNTER FLANGE, HOLE ETC. INTRODUCTION: - IN THIS EXERCISE, WE HAVE TO CREATE A BRACKET FOR THAT WE CAN USE DIFFERENT FEATURES LIKE COUNTER FLANGE, BREAKE CORNER, BEAD, NORMAL…

  TITLE: - NX_BRACKET-2_BEREKAR_MAHENDRA OBJECTIVE: - THIS BRACKET-2 EXERCISE IS GOOD FOR UNDERSTANDING THE NX SOFTWARE FEATURE VERY BRIFLY LIKE GUSSET, COUNTER FLANGE, HOLE, NORMAL CUTOUT, ETC. INTRODUCTION: - IN THIS EXERCISE, WE HAVE TO CREATE A BRACKET FOR THAT WE CAN USE DIFFERENT FEATURES LIKE COUNTER FLANGE,…

Project Objective:- In This Project, I am Going to Suggest a Big Car for Mr. D.S. Pughazhyendhii Under 8 to 10 Lakhs on Road for Official and Family Purpose Traveling Distance Around 500km. Suggested Cars Listed Below: - Hyundai Vennu 1.4 CRDi MTE. Mahindra XUV 3000 1.5W6. Nissan Kicks XE Diesel. Tata Nicxon KRAZ Plus…

Write one page about Under body coating and its purposes It is the protective coating given to the car’s underbody to protect it from corrosion and from being damaged. It is a rust – preventable coating outside of the vehicle. There are types of under body coating based on the type of damage and the type of…

REPORT OF HOOD DESIGN AIM: Create the hood inner panel and its assembly as per the given hood outer panel and master-section. Objective: - To create Hood inner panel as per the master section, and design consideration. To create complete Hood assembly with proper positioning of Hinge, Latch and Striker. INTRODUCTION: -…

European Regulations Requirement:- Take the outline of the when and the fender. Make the center of the when circle. Draw horizontal and vertical perpendicular axis from the center of the wheel circle. Draw lines at 300 and 500 line from the horizontal. Make point on the fender line at 150mm from the horizontal. Extent…