DETAILED REPORT ON BASE BRACKET COMPONENT CREATION  Initially observed the A surface component and verified the draft angles with each surface  and even checked the tooling axis direction in which axis tooling axis creation using bisecting method  initially created a dummy tooling axis by addressing the…

detailed report of coin hollder surface design                    1.intiallly observed the a surface and addressed the tooling axis direction to be at x axis direction by extracting a surface which is normal to the plane created a point and line tangent to the pont and…

detailed report on switch bezel exersice  initially created the tooling axis with rexpective tooling direction by extracting the surface normal to the plane and axis  and observed the a surface and draft analysis done on it to verify the tooling axis  surfaces were created with srective the a surface with…

DETAILED REPORT EXPLAINING ABOUT THE  UNDER BODY COATING  UNDERBODY COATING:                  The process of painting several layers of coating re given over the surface of a car to make it suitable to with stand damage occuring due to mechanicle and chemical…

BUMPER CHALLENGE REPORT TOOLING AXIS CREATION AND DRAFT ANALYSIS: Initially verified the input given with respective all sides and with repective proper boundry too  then selected the flat surface through which entier boundry can be seen and selected the flat surface and checked with the partial draft analysis …

                                                           DOOR TRIM LOWER CHALLANGE REPORT TOOLING AXIS CREATION AND SURFACE PARTIAL DRAFT ANALYSIS . CHECKED THE SURFACES WITH RESPECTIVE ALL THE AXIS AND EXTRACTED ONE FLAT SURFACE THROUGH WITH ALL THE SURFACES ARE SEEN WHEN PARTIAL DRAFT ANALYSIS IS DONE  CREATED A POINT…

                                 REPORT REGARDING CREATION OF B SIDE FEATURES OF DOOR HANDLE  TOOLING AXIS CREATION  CREATED A TOOLING ASXIS BY USING NORMAL TO SURFACE METHOD BY EXTRACTING ONE FLAT SURFACE PERFORMED DRAFT ANALYSIS…

                                                            CORE AND CAVITY DESIGN OF SWITCH BEZEL TOOLING AXIS CREATION AND SURFACE PARTIAL DRAFT ANALYSIS . CHECKED THE…

                                                           DOOR TRIM LOWER CHALLANGE REPORT TOOLING AXIS CREATION AND SURFACE PARTIAL DRAFT ANALYSIS . CHECKED THE SURFACES…

         DOOR TRIM LOWER APPLIQUE WITH ENGINEEERING FEATURES CHALLANGE REPORT TOOLING AXIS CREATION AND SURFACE PARTIAL DRAFT ANALYSIS . CHECKED THE SURFACES WITH RESPECTIVE ALL THE AXIS AND EXTRACTED ONE FLAT SURFACE THROUGH WITH ALL THE SURFACES ARE SEEN WHEN PARTIAL DRAFT ANALYSIS IS DONE …

BENCH MARKING  BENCHMARKING IS A PROCESS OF COMPARISION BETWEEN SIMILAR PRODUTS THAT IS CARS AND THEIR PARTS EITHER EXTERIOR OR INTERIOR AND THEIR SPECIFICATIONS AND FEATURES PROCESS BY WHICH THE PRODUCTS ARE MANUFACTURED AND METHODS  SERVICES AVAILED BY THE PARTENT COMPANY TO THE CUSTUMERS EITHJER FOR MARKETING…

REPORT  INITIALLY CREATED ALL THE PART BODIES USING THE PART WORK BENCH WITH PROPER CONSTRAINTS AND IMPORTED THEM INTO THE ASSEMBLY WORK BENCH USING EXISTING COMPONENT COMMAND  FIXED THE MAIN COMPONENT WITH REFERENCE TO THAT COMPONENT CONSTRAINED ALL THE OTHER PARTS SO THAT IT DOESNT MOVE  AND CREATED THE…

DESIGNING AND MODELLING OF A HOOD USING CATIA V5 SOFTWARE Introduction to HOOD A car hood also referred to as a bonnet in some other countries is the hinged cover that rests over the engine of a front-engine vehicle. Its purpose is to provide access to the engine for repair and maintenance. Car hoods are typically…

Report on the section modulus of the hood designed      Section Modulus Section Modulus is a geometric property used to calculate the bending stresses in a structural member.   Mathematically,   It is defined as the ratio of the moment of inertia of a section about its centroidal axis and to the…

REPORT ON DEVOLOPMENT OF DOOR TRIM PANEL CREATION USING THE INPUTS   DEVELOPMENT OF DOOR TRIM PANEL Automotive Plastic Trim: The design of Automotive Interior and Exterior plastic components is called Trims. The plastic components that you see inside the car are Interior. Ex: Dashboard, Instrument Panel, Doors, seating,…

report of the calculation made on the wheel arch with fener design based on the standards  Introduction to Wheel Arch:  It is a semi circular  part of the fender positioned above the wheel of the vehicle  it is usually designed as a cover or shield over the tyre along its circumference  Its main function is to avoid the…

Introduction to a Fender The fender is an important component on the exterior of the car as it houses the wheel arch which in turn houses the vehicles wheels. The wheel should ideally sit inside the boundaries of the fender to avoid the it from spraying abrasive particles into the air which could potentially cause damage,…

                                                                                  REPORT ON ROOF DESIGN BASED ON THE…

report on back door designing and modelling  AIM:                Using the provided styling surface to come up with a back door and using appropriate design methodologies and make the necessary reinforcements and emboss.   Backdoor              …

Report on giving the elecrical defination to the connectors and clip and creation of catalog document containing these components. Aim: To give the electrical defination to the given clip and connectors in electrical part design after giving the geometrical parameters and then creation of catalog document of them…

                   Wiring harness routing & packaging Rules Week 3 Challenge                  AIM: To solve the above assignment questions and define the necessary electrical properties in the respective…

Downloading Connector Data from te.com  After downloading Connectors we have define the Connectors as Electrical Parts CONNECTORS 1. DT06-08SA    Geometrical features  Points and Axis System in created  by using these Features we have to Define mechanical part as electrical part i.e Connector. CONNECTOR DEFINITION CONNECTOR…

AIM:- To route the Harness layout in Eletrical workbench by using the connectors which taken as an inut Objectives: To Check the Bundle Connectivity. Adding Annotations to connectors. check for bundle warning Generate CATPart and make STP or IGS File...   INPUT We have to route the harness as shown in below Harness…

AIM:-  Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. OBJECTIVES To design Harness Flatten using Exisisting Wiring harness To draft the Harness Assembly as per…