…

                                                                                        MODELING OF…

                                                                      1D Element creation  Objective :  To create 1D element for a given…

                                                                               HOOD MESHING  Objective:  Two extract…

3D Tetra Meshing    Housing Model :  Import the given model in iges form. Delete the solids using delete entities option.  After performing the above task, Now do a 2D mesh Using automesh option, With element size as 5mm And use trias as only option.  After meshing check for minimum and maximum length Using element check…

creation of 1d connectors  Importing the given geometry  After importing, we have to do a mid-surfacing for individual components. If there are problems with the geometry, we have to do geometric cleanup.  After mid surfacing, we have to assign material, property for individual components and also, we have to give a thickness…

Meshing of door inner panel  The first step is to import the given geometry in iges form.   In order to perform mid surface we need to defeature the fillets and other surfaces So that proper meshing will be produced. Geometry>> Defeature>>surf fillet.  After Defeaturing We have to do an elemental cleanup.  Now we have…

Meshing of rear wheel holder  Import the given geometry in iges form.  deleting the solid from the geometry by using the option delete>>solids>>delete entity.  Now we have to extract mid surface from the original component by using the option geometry>> midsurface>> extract.  After the mid surface is done now we have to…

Stress concentration on a plate with hole  Aim: Stress concentration on a plate with holes  Objectives:  To design A plate with hole Model  to design A plate with three holes with different diameters  To find out maximum deformation and stress development in the above models  Comparing the results of two cases  Procedure: …

Spur Gear  Aim: to perform static structural analysis on spur gear using ansys  Objective:  To carry out add analysis or per game with different materials  to find out equivalent stress ,total deformation, stress intensity.  to choose material based on results.  Procedure:  first we need to import 3D model of spur gear…

Bevel gear  Objective:  To perform grid dependency test with bevel gear four different mesh sizes.  Grid dependency test:  The grid dependency test is which analysis begins with the coarse mesh and is made finer for each run until the results do not change significantly.  Procedure:  First, we need to open model in space…

Verification of weld joints  Procedure:  First, we need to assign Material for the Weld joint four different cases.  now we have to open space claim in order to check the components proper or not.  Now we have to define contact faces of the wealth geometry by selecting the contact or target bodies. define the type of contact…

Rail wheel and track  Objective:  stimulating the rail wheel and track using static structural material in order to evaluate the result.  Procedure:  importing the geometry in mechanical module and assigning material for the component.  Now we have to assign contacts for the rail wheel and track, the contacts are frictional-…

Wire bending  Procedure:  Assigning the material property for the given component.  now we have to assign contacts between the wheel, wire and lever. The contact used will be frictional from wire to lever.  Now we have to assign a revolute joint in order to rotation of the wheel  after the operation is complete we now…

Sheet metal bending  Objective:  Stimulating sheet metal bending with three different materials of aluminum alloy 1199, copper alloy nl, magnesium alloy nl. and to find out equivalent stress, directional deformation, equivalent strain.  Procedure:  assigning the material properties for the given component and updating…

Rolling operation  Objective:  To stimulate the rolling operation on a work piece of a copper material and to determine equivalent stress and equivalent plastic strain.  Procedure:  Importing the given component and assigning Copper NL material.   We need to modify the geometry by increasing the workpiece to 60mm. And…

Sphere pressing on a plate  Objective:  To perform analysis add stimulate sphere pressing on a plate Using structural Steel for both sphere and plate With the material of nonlinear. and should I have a displacement of 4MM downwards.  Procedure:  first we need to input engineering materials with specified property.,then…

Long piston with Cam  Objective:  To perform a transient analysis on a piston and a cam mechanism I need to run analysis with frictionless contact, frictional contact with frictional coefficient of 0.1,0.2 for the following cases.  Procedure:  Importing the given geometry and assigning material for the geometry. now we…

Universal joint  Objective:  Two perform transient structural analysis on a joint with spring using three different materials as structural steel, stainless steel, titanium alloy. and to find equivalent stress and total deformation and also to compare the result.  Procedure:  first, we need to assign materials for the…

Worm Gear  Objective:  to perform a transient structural analysis of a worm gear and to determine the equivalent stress, equivalent strain and total deformation.  Procedure:  first, we need to import the model and assign material for the geometry, We need to open it in space claim in order to check whether any abnormalities…

Car Crash simulation  Objective:  To perform three different values of thickness for the car body and to analyze total deformation and equal stress on the model.  Procedure:  first we need to import the model in mechanical module and also to assign material for the model.  For the car body we need…

Machining with planer  Objective:  To perform the explicit dynamics stimulation for planner machining using ANSYS workbench.  Procedure:  Importing the given CAD model in space claim in order to check any geometry malfunction. then assigning properties and material for the geometry.  body intersecting connection is provided…

Tension and torsion test  Objective:  To perform Tension and torsion test for a given component and to determine total deformation and temperature.  Procedure;  importing the given geometry and assigning specific material for the component.  first, for tension test we need to give a coordinate system for both left and…

Bullet penetrating a bucket  Objective:  to perform a stimulation using ANSYS workbench for a bullet penetrating a bucket and also to determine total deformation and equivalent stress and other behaviors.  Procedure:  in order to start first we need to assign material for the component, the materials are going to be 3…

The part which was created in the above challenge is now opened in assembly file, now we need to open the cavity part and change its transparency and we need to sketch in order to create the sliders.  a solid slider body is formed which needs to be fitted in the cavity block  the slider is cut extruded so that it may fit…

Project challenge  Objective:  to create a mold using the different components given by splitting into core and cavity.  Procedure:  importing the given geometry in SolidWorks and analyzing the geometry if there are any mistakes.  first in the toolbar we need to go to the mold design option and then we have to choose draft…

Week 9 challenge  Objective:  to create a mold using the different components given by splitting into core and cavity.  Procedure:  First we need to open assembly file and then insert the component which was made in the previous part now we need to edit the core part in order to create a slider …

Week 12 challenge  Objective:  to create a mold using the different components given by splitting into core and cavity.  Procedure:  In the previous challenge we created sliders for the component since there are many undercuts formed, we need to create ejector pins in order to separate cavity from…