DESIGNING OF AMERICAN CHOPPER BIKE USING SOLIDWORKS OBJECTIVE: The objective of this project is used to create a model of different parts of chooper using the software solidworks To assemble the different parts of modeled for the chopper To create a Photorealistic model of chopper and Render the model using solidworks…

1. Radar Mast      2. Yacht Assembly 1.Title – Modelling and Rendering of Yacht. 2.Objective- Design and modelling of components of Yacht, using sketch tools and 3D modelling features of Solidworks. Assembly of Yacht using Solidworks assembly tool. Rendering images of Yacht in Photoview360 and Solidworks visualization…

  OBJECTIVE: Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm                …

AIM:- Follow the below-mentioned quality criteria, mesh the component given below and assign thickness Target Element Length = 5mmS.N Quality Criteria Value1 Aspect Ratio 52 Skewness 453 Warping 154 Taper 0.55 Min. Length 2mm6 Max. Length 8mm7 Min angle Quad 458 Max angle Quad 1359 Min angle Tria 2010 Max angle Tria 12011…

CREATING TETRAHEDRAL ELEMENTS USING HYPERMESH I. Tetramesh for housing and hub assembly:- Tetrahedral elements are solid elements which have been extracted from 2-D tria elements. Hypermesh builds 4 and 10 noded tetras. Hypermesh provides two methods of generating a tetrahedral elemental mesh. The volume tetra mesher works…

AIM: To create various types of 1 D connectors. Create connector and Attach the various parts of the given model1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L)2. Left_Rail_2 & Front_truss_1:- Quad elements3. Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 2 Layers and 5 mm Diameter4.…

ABSTRACT The given side door model is taken a midurface and then the geometry of the midsurface component is cleaned for doing the mesh. Then the meshed component is checked for the quality parametres. FEA: FEA is a FINITE element analysis is a numerical method for solving problems of engineering and mathematical physics…

AIM To mesh the given component under mentioned quality criteria and assign thickness to it. PROCEDURE The given component is imported as .stp file format and the component is viewed by topo mode. The given component is checked for the uniformity in its thickness all over the geometry using distance option. The component…

OBJECTIVE : To Clean up the given geometries and extract midsurface and mesh them with 5mm 2D shell elements and assign proper thickness to them PROCEDURE : 1. Firstly Import the geometry which is provided in the Hypermesh windows. Now, keep the view in By topo mode to see the geometry clearly and observe any errors in…

Aim: To study about the starter file and engine file in RADIOSS by changing the parameters for the given file. And also perform a 3D meshing on the given components of which one will have tetra mesh and the other one will have hex mesh Objective: 1. Check the material properties of the rail component and calculate the…

   Objective: Comparison of results with base simulation and improved shell element properties 1.Using the crash beam file from the previous assignment, change the run time to 55 ms. 2. Change the number of animation steps during simulation to a minimum of 25 and maximum of 60. 3. Run the base simulation…

AIM:To compare the results of the different material laws i.e. Law2, Law27 and Law36.OBJECTIVES OF THE PROJECT:To assign different material laws on the given component.To prepare case wise scenario and compare the results.To compare the total no of cycles, energy error, mass error and simulation time of all the cases.To…

Aim :1) To study the different types of interfaces and to compare the results of radioss simulation for each interface case.2) To create a mesh with the size of 6mm for bumper assembly.Scope of the project:1) In this project first we have performed 2d meshing on bumper assembly with an element size of 6mm.2) For crush…

 AIM:To create a setup for frontal crash of car BIW and request for Time History plots.OBJECTIVE:1.Check unit system and either follow[Mg mm s] or [Kg mm ms].2.Create appropriate interface ,friction 0.2 and recommended parameters.3.Make sure of no penetrations and intersection.4.Correct rigid bodies if any issues.5.Create…

Crashworthiness Analysis using HyperMesh and Radioss#Project 2 - Side Body Crash Simulation Challenge AIM: To perform the crash on the Side body of the car to a pole and analysis where stresses are working on it. OBJECTIVES:Side Body-BIW1. Checking the unit system and either following [Mg mm s] or [Kg mm ms].2. Creating…

  Week - 3 For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria)    S.No  Quality Criteria  Value  1 Target/Average length  …

Aim For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacingtechniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with given element Quality criteria.Procedure Geometrical clean-up:1.Open model and measure the distance…

Objectives:The objective of this project is to performing meshing for Tool test 1 for component1 & Component 2 using the ANSA tool.From the given Component, Checking geometrical errors and mesh with given element quality criteriaExtracting the mid surface from the component.After meshing the component the thickness…

ABSTRACT:By using CAE Pre-Processing Tool ANSA & to develop Tetra meshing for a Rear-View Mirror METHODOLOGY:1. Importing the CAD geometry in ANSA2. Checking out the errors and Assigning Property ID (PID) for each surface.3. Assigning Quality Criteria4. Meshing and Improving Mesh Quality (Ortho Tria & Tria Mesh…

OBJECTIVEIn this tool test in the given component intake manifolde we have to check for the geometrical errors and mesh with the givenelement Quality criteria. Use tetra elements to model the component and there should not and kinks and dips on the surface of thecomponent. PROCEDUREImport the model into the ANSA and check…

AIM:For the given rear door FE model, create and apply different PIDs for different components and perform suitable connections.OBJECTIVE:To connect the different components in the rear door FE model with suitable connections.PROCEDURE:IMPORTING THE CAD MODEL:The CAD model is imported into the workspace by using file >…

Basic of Morphing (ANSA) Morphing ANSA encompasses a full – fledged Morphing menu which is completely integrated with ANSA’s interface and doesn’t require anyadditional module installations or licenses. The functions of the Morphing menu can be used to efficiently re-shape both FE and/orGeometry based…

  AIM:  Pre-processing of the car instrument panel using ANSA Google drive Link:; KEYWORDS: Mid-surface Extraction, Shell Meshing. OBJECTIVE:   Introduction to shell meshing i.e. 2D meshing Geometry check & Topological error clean up  Mid surface generation  Meshing the geometry …

Report documentation https://docs.google.com/document/d/1mbMQ-ZvdmkIsT8OJo7lCnF8RQ4YJzVDvuoInG3duWIk/edit?usp=sharing Google Link: https://drive.google.com/file/d/1EeTpAT5UPOHhj1YG51_mKPaPx7Nl5Ggz/view?usp=sharing  

AIM : TO SIMULATE THE 'FORWARD KINEMATICS' OF A 2R ROBOTIC ARM USING A MATLAB.OBJECTIVE :1. Write a program in matlab to 'SIMULATE FORWARD KINEMATICS' of a 2R robotic arm.2. To create a animation and movie from their plot obtained through programing. INPUTS :(x0,y0) = strating point of the link(x1,y1) = ending point of…

Project Report:Step1 : Declaring the input variablesValues of Damping coefficient, Acceleration due to gravity, Length of the string and Mass of the pendulum bob is defined.Step2: Defining the initial condition and time spanInitial condition is defined as 'theta_0 = [0;3]' which implies that at time t = 0, angular velocity…

  Abstract:The Lithium-ion battery is one of the most common batteries used in Electric Vehicles (EVs) due to the specific features of high energydensity, power density, long life span and environment friendly. With the development of lithium-ion battery technology, different materials have been adopted in the design…