Wheel arch clearance calculator: the EU 30°/50° wheel guard rule, the SA to SE course check and Japan's 第178条

The EU wheel guard rule (Regulation (EU) 2021/535, Annex V) asks the guard to cover the full tyre width between radial planes 30° in front of and 50° behind the wheel centre, to end at the rear no higher than 150 mm above the axle with point A outboard of the tyre centre plane, and to have a recess at least 30 mm deep. "L > 10 mm at sections SA to SE" is a course and OEM CAD check with a margin, not a number in the law.

Enter the tyre, the arch edge and the fender edge: the calculator draws the 30°/50° planes, point A and SA to SE, and gives three verdicts side by side: the EU text, Japan's rule and the course check of Skill-Lync's Automotive Sheet Metal Design course. Skill-Lync read 1,792 public wheel arch reports: 455 give the course model's numbers, 193 of them pass SB = 10.000 under a "greater than 10 mm" rule, and none cites the EU regulation. Free, runs in your browser.

EU 2021/535 Annex V Part 2 · EU 1009/2010 Annex II · MLIT 細目告示 第178条 (2023.9.22) · 49 CFR 571 · UN R30 Rev. 3 · checked against a separate solution (2,580 checks at build) · Updated 22 Nov 2026

An illustrative hatchback: arch edge a 345 mm circle centred 10 mm ahead of and 20 mm above the wheel centre, front end 40 mm and rear end 90 mm above the axle; fender edge 94.5 to 104.5 mm out from the tyre centre plane. It meets the EU text and fails the course's 10 mm check from the 50° line back (SC, SD, SE).

EU text (law)metcover 5.3 mm in the zone
Course SA to SEfailL > 10, a > 5
Japan 第178条mettyre, wheel, cap
z = 150SASBSCSDSEAfront ←→ rearzone: 30° front to 50° rear (EU 2.2.1.1, Japan 第178条)
wheel faceL = 9.00 mmfender edge Y = 101.5tyre outer face 92.5tyre centre planesection at 50° rear · outboard →
-5051015100° f50° f30° f0°50° r100° rcourse > 10 mmSASBSCSDSEL (mm) vs section angle · shaded = EU 30°/50° zone
  • EU 2021/535 Annex V (law): met. Smallest cover in the 30°/50° zone with the tyre envelope: 5.3 mm.
  • Course check (SA to SE, L > 10, a > 5): fails at SC, SD, SE. This is a CAD check method, not a legal limit.
  • Japan 第178条 2項 一号: met.
  • SE is 64.15° behind the vertical (point A at x = −309.6, z = 150), SD bisects SC and SE at 57.07°. The course sheet's "US" line, L > 5 mm from −100° to +100°: smallest L 2.0 mm at −100°; no US federal rule asks for it.

Sections SA to SE

SectionAngleY fenderL (CAD tyre)Cover with envelopea (radial)Course > 10
SA0.0° fwd104.5012.008.3054.1pass
SB30.0° fwd103.5011.007.3056.6pass
SC50.0° rear101.509.005.3038.8fail
SD57.1° rear98.976.472.7736.0fail
SE64.1° rear96.493.990.2933.2fail

The three verdicts, clause by clause

EU 2021/535 Annex V, Part 2 (law)ValueResult
Guard covers the tyre width b between 30° front and 50° rear (2.2.1.1)smallest cover 5.3 mm at −50° (tyre envelope b = 192.4 mm)met
Rear of the guard ends at or below 150 mm above the wheel axis (2.2.1.2)rear end at 90 mmmet
Point A lies outboard of the tyre's median plane (2.2.1.2.1)Y = 96.5 mm at −64.1°met
Recess depth p in the vertical plane ≥ 30 mm (2.2.1.3.1)40 mmmet
Lower edges within c ≤ 2r of the wheel axis (2.2.1.3.2)357 mm vs 2r = 582 mmmet
Japan 細目告示 第178条 2項 一号 (law)ValueResult
Wheel, wheel cap: no projection beyond the body directly above (第178条 2項 一号)21.5 mm insidemet
Tyre (lettering and ribs aside) does not project (同号 ロ)9.0 mmmet
Sidewall ribs / bands may project only if their projection is under 10 mm (同号 ロ(2))0.0 mm rib: allowedmet
Course check (not law)ValueResult
L at SA (0° fwd) (> 10)12.00 mmmet
L at SB (30° fwd) (> 10)11.00 mmmet
L at SC (50° rear) (> 10)9.00 mmnot met
L at SD (57.1° rear) (> 10)6.47 mmnot met
L at SE (64.1° rear) (> 10)3.99 mmnot met
a at SB (30° fwd) (> 5)56.6 mmmet
a at SC (50° rear) (> 5)38.8 mmmet

What does the EU wheel guard regulation actually require?

Five things, with the car at its mass in running order plus one front passenger and the steered wheels straight (Commission Implementing Regulation (EU) 2021/535, Annex V, Part 2, points 2.2.1.1 to 2.2.1.4; the same wording as Annex II of Regulation (EU) No 1009/2010, which it replaced). It applies to M1 cars; N1 and N2 vans up to 7.5 t and O1/O2 trailers may use it at the maker's choice.

  • Cover (2.2.1.1): between radial planes 30° to the front and 50° to the rear of the wheel centre, the guard's overall width q must cover the total tyre width b, "taking into account the tyre envelope as well as the extremes of the tyre/wheel combination(s)". Lettering, decorations and sidewall ribs do not count (2.2.1.1.1).
  • Rear end and point A (2.2.1.2): the rear of the guard must not end above a horizontal plane 150 mm above the wheel axis, and point A, where the rear edge meets that plane, must lie outboard of the tyre's median plane.
  • Recess depth (2.2.1.3.1): p at least 30 mm in the vertical plane through the axle, reducing "progressively to zero" towards the 30° and 50° planes.
  • Lower edges (2.2.1.3.2): the distance c from the lower edges of the guard to the wheel axis must not exceed 2r, r the static radius.
  • Adjustable suspension (2.2.1.4): p and c are checked in the normal running position.

In this page's terms, the cover rule is a single inequality over the whole zone, with the envelope width:

There is no "L > 10 mm" and no "a > 5 mm" anywhere in the text. A cover of 0.1 mm meets the law; the course check would fail it. The other way round matters more: SD and SE lie behind the 50° plane, outside the EU zone, so a fender can fail the course at SD and SE and still meet the law. The default example does exactly that: cover 5.3 mm with the R30 envelope, but L = 9.0, 6.5 and 4.0 mm at SC, SD and SE.

How are sections SA to SE drawn?

SA is the vertical through the wheel centre, SB is 30° forward and SC 50° rearward: the two EU planes. SE goes from the wheel centre to point A, the rear arch edge 150 mm above the wheel centre. SD bisects SC and SE. At each section, L is the lateral cover, how far the fender edge sits outboard of the tyre's outer face, and a is the radial gap from the tread to the arch edge:

For the default arch (a 345 mm circle centred 10 mm forward and 20 mm up), point A is at x = −309.6 mm, so SE is 64.15° behind the vertical and SD 57.07°. A circle centred on the wheel with R = 400 mm puts SE at acos(150/400) = 67.98°. Put the 150 mm above the ground instead and SE moves by about the wheel radius: a different section, a different L. The calculator's section slider draws L at any angle.

How big is a 205/55 R16 tyre, and what is its "envelope"?

631.9 mm across. The code gives the width in mm, the sidewall height as a percentage of the width and the rim in inches:

The EU text asks for the "tyre envelope": the largest width and diameter the tyre's approval allows. UN Regulation No 30 (Revision 3) lets a radial tyre's overall width exceed the section width by 4% (6% for diagonal, 6.1.4.2) and bounds the outer diameter with coefficients 0.97 and 1.04 (1.08 diagonal, 6.1.5.3); snow tyres may exceed Dmax by 1% more (6.1.5.4):

For 205/55 R16 that is up to 213.2 mm wide and 625.1 to 640.9 mm across. This page takes S as the nominal width (measuring rim = theoretical rim; R30 6.1.1 adjusts it by 0.4 times the rim width difference otherwise). Going to 205/50 R17 changes D by 4.9 mm, so a shrinks by 2.4 mm all round; 225/45 R17 also moves the outer face 10.0 mm out, which is 10.0 mm less L at every section. Those are the "extremes of the tyre/wheel combination" the regulation means: check the widest tyre and the lowest offset the car is sold with, not only the CAD tyre.

What do the 30 mm depth and the 2r rule mean?

The recess depth p is how deep the guard reaches over the tyre, measured from its outer and inner edges at the vertical plane through the axle: at least 30 mm there. The text only says it "may be reduced progressively to zero" towards the 30° and 50° planes. This page reads that as linear, which is an assumption, not the regulation's wording:

So 15 mm at 15° forward and 15 mm at 25° rear. The c rule caps the distance from the wheel axis to the guard's lower edges at 2r; this page measures c as the straight distance from the axis to each end of the arch edge, our reading of Figure 1. For the default car that is 357 mm against 2r = 582 mm.

What do Japan and the US actually require?

Japan. 道路運送車両の保安基準の細目を定める告示 第178条 第2項 第一号 (2023.9.22 edition): with the car in the straight-ahead position, the rotating parts (tyre, wheel step, wheel cap and so on) between the vertical plane through the axle and the planes 30° forward and 50° rearward through it must not project outward beyond the body (fender and so on) directly above. For passenger cars (not 10 seats or more, two- or three-wheelers, and others listed) on tyres that meet UN R30, the parts of the tyre that may project are sidewall lettering or marks, and sidewall protective bands and ribs whose projection is under 10 mm. So Japan's 10 mm is a rib projection allowed, not a clearance required, and wheels and caps get none. The "L > 5 mm in area K" of the course sheet is not in the text.

United States. No federal rule. The 80 sections of 49 CFR 571 subpart B (the FMVSS) include none on wheel guards or fender coverage; fender and mudflap rules sit in state vehicle codes, mostly for trucks. The sheet's "L > 5 mm from −100° to +100°" is a course or company check. The calculator still shows the smallest L over that range (2.0 mm for the default car), labelled as such.

India. ICAT's ready reckoner for CMVR type approval of M1 cars lists a "Wheel Guard" test with IS 13943:1994 as the reference standard. We have not read IS 13943's text (a BIS standard on sale), so this calculator does not check it.

What did 1,792 student reports write?

Skill-Lync matched 2,973 public reports titled "Fender Design - Wheel Arch Challenge", "Fender Design" or "Fender Design Challenge" on 22 Nov 2026; 1,792 are about the wheel arch (the title or the text says so). 849 give L at all five sections in their text; 900 more have their numbers only in images and 43 have none. The table sorts the 849 by the values in their text.

L at SA to SE in the textReportsExamples
The course model's numbers: SA 9.949, SB 10.000, SC 0.114, SD 2.887, SE 5.997 (rounded, signed or not)4091, 2, 3
The same five numbers with SA and SB the other way round461, 2, 3
Same SA to SC, different SD and SE (SE or SD drawn another way)1491, 2, 3
A second set: SC about 3.0, SD under 1 mm431, 2, 3
Radial gaps (a) written in the L list761, 2, 3
Other values1261, 2, 3
Total849
  • Sign. Of the 455 reports with the course model's numbers, 206 write SC to SE as negative (the tyre's outer face is outboard of the fender edge there) and 249 as positive (1, 2, 3). The course verdict is the same either way; the EU one is not: a negative L at SC, inside the 30°/50° zone, means the guard does not cover the tyre.
  • > or ≥. 193 mark SB = 10.000 as PASS while their own rule says "greater than 10 mm" (1, 2, 3); 86 pass it under a "≥ 10 mm" rule, which is consistent. 37 mark SA ≈ 9.95 as PASS (1, 2, 3).
  • Radial gaps in the L column. 101 list a radial gap (about 26, 44, 38, 41, 44 mm) at all five sections against the 10 mm L limit and call them PASS (1, 2, 3). The course asks for "a" only at 30° and 50°, against 5 mm.
  • SE and SD. 536 put the 150 mm above the wheel centre or axis, as the course and the EU text do; 1 puts it above the ground (1). 149 agree on SA to SC but not on SD and SE, which is where the construction differs; 6 have SD and SE swapped.
  • Direction. 18 write "50° forward" for the rear line (1, 2, 3).
  • Law. 394 call the −100° to +100° check a US regulation or standard (1, 2, 3) and 718 describe a Japanese regulation or standard. None cites Regulation 1009/2010, 2021/535 or the older Directive 78/549/EEC.

Counts as of 22 Nov 2026, n = 849 reports with L values in text (1,792 on the wheel arch, 900 image-only), from the text of each public report: Skill-Lync's own data, a starting point, not a grade. Numbers inside images are not counted.

  • All positive: on the course model, 206 reports write SC to SE as negative (the tyre's outer face is outboard of the fender edge there) and 249 as positive. A distance tool returns an unsigned length, so say which side the tyre is on: that decides the EU check, not the course one.
  • SA: L = 9.949 mm does not meet the course's L > 10 mm.
  • SB = 10.000 marked PASS, but your rule is "L > 10 mm": exactly 10 is not greater than 10. Either write the rule as "≥ 10 mm" or mark it FAIL. 193 public reports mark SB = 10.000 PASS under a "greater than 10 mm" rule (1, 2, 3).
  • SC: L = 0.114 mm does not meet the course's L > 10 mm.
  • SD: L = 2.887 mm does not meet the course's L > 10 mm. SD and SE lie behind the 50° plane, outside the EU 30°/50° zone.
  • SE: L = 5.997 mm does not meet the course's L > 10 mm. SD and SE lie behind the 50° plane, outside the EU 30°/50° zone.
  • a at SB (30° fwd) = 43.6 mm meets the course's a > 5 mm. The EU text has no "a" limit; it asks for the recess depth p ≥ 30 mm in the vertical plane (2.2.1.3.1).
  • a at SC (50° rear) = 38.4 mm meets the course's a > 5 mm. The EU text has no "a" limit; it asks for the recess depth p ≥ 30 mm in the vertical plane (2.2.1.3.1).
  • The course's "US: L > 5 mm from −100° to +100°" and "Japan: L > 5 mm in area K" are not the law. No US federal standard (49 CFR 571) covers wheel guards, and Japan's 第178条 says the tyre, wheel and cap must not project beyond the body between the 30° and 50° planes, with sidewall ribs under 10 mm allowed to. 394 public reports call the −100° to +100° check a US regulation or standard (1, 2, 3).

What this calculator does not cover

  • Real 3D surfaces. The arch edge is a side-view curve and the fender edge a lateral position at a few angles. A CAD check cuts the actual fender and tyre at each plane; use this to understand the rule, then measure in CATIA or NX.
  • Suspension travel and steering. The EU and Japanese checks are static, straight ahead, at a stated load. Bump, rebound, steering lock and snow chains (EU 2.3) need the wheel envelope, not one position.
  • Twin wheels, trucks and other categories. Only single wheels on M1 cars; N2/N3 spray suppression (Annex V, Part 4 of 2021/535) is a different rule.
  • India's IS 13943. Listed by ICAT for M1 type approval; not read, not checked.
Learn automotive sheet metal design

Fender, hood and door design come with rules like this one: surfaces that must cover, clear and pass a regulation. The wheel arch challenge is part of Skill-Lync's Automotive Sheet Metal Design course.

Frequently asked questions

What does the EU regulation require for a wheel arch?

Between radial planes 30° in front of and 50° behind the wheel centre, the wheel guard must cover the full tyre width, using the tyre envelope (Regulation (EU) 2021/535, Annex V, 2.2.1.1). Its rear must end no higher than 150 mm above the axle, point A outboard of the tyre centre plane, the recess at least 30 mm deep.

Is L > 10 mm at SA to SE a legal requirement?

No. Neither Regulation 1009/2010 nor 2021/535 has an L of 10 mm or an "a" of 5 mm. The law asks for cover of at least zero, meaning the tyre must not stick out, between the 30° and 50° planes. Sections SA to SE with 10 mm are a CAD check method, with a margin, taught for the challenge.

How do you draw the SE and SD sections?

SE runs from the wheel centre to the point where the arch's rear edge crosses a horizontal line 150 mm above the wheel centre: that point is point A of the EU text. For an arch circle of radius R centred on the wheel, SE sits at acos(150/R) behind the vertical. SD bisects the angle between SC (50° rear) and SE.

What does Japan's rule (第178条) say about wheel arches?

With the car straight ahead, the tyre, wheel and wheel cap between the planes 30° forward and 50° rearward through the axle must not project beyond the body directly above (細目告示 第178条 2項 一号). For passenger cars on UN R30 tyres, sidewall lettering and protective ribs under 10 mm may project. Japan sets no 5 mm clearance.

Is there a US regulation for wheel arch clearance?

No federal one. None of the 80 sections of the US Federal Motor Vehicle Safety Standards (49 CFR 571, subpart B) covers wheel guards or fender coverage. Fender and mudflap rules in the US are state vehicle codes, mostly for trucks. The course sheet's "L > 5 mm from −100° to +100°" is not a federal rule.

How do you calculate the diameter of a 205/55 R16 tyre?

Rim diameter 16 × 25.4 = 406.4 mm, sidewall height 0.55 × 205 = 112.75 mm, so D = 406.4 + 2 × 112.75 = 631.9 mm. UN R30 lets a radial tyre's outer diameter run from 625.1 to 640.9 mm and its overall width up to 213.2 mm (4% over 205).

Related on Skill-Lync

Sources

  • Commission Implementing Regulation (EU) 2021/535, Annex V, Part 2 (wheel guards), points 1.1, 2.2.1 to 2.2.3, Figure 1 explanatory note; Annex V Part 4 point 4.1 for N1, N2 ≤ 7.5 t, O1, O2 (EUR-Lex CELEX 32021R0535, read 22 Nov 2026).
  • Commission Regulation (EU) No 1009/2010, Annex II, points 2.1 to 2.1.4 and Article 2 (tyre envelope) (EUR-Lex CELEX 32010R1009, read 22 Nov 2026).
  • 国土交通省, 道路運送車両の保安基準の細目を定める告示 第178条 (車枠及び車体), 2023.9.22 edition, 第2項 第一号 and ロ(1), (2) (mlit.go.jp/jidosha/content/S178.pdf).
  • 49 CFR Part 571, subpart B, the list of Federal Motor Vehicle Safety Standards (Cornell LII, read 22 Nov 2026).
  • UN Regulation No 30 (pneumatic tyres), Revision 3, as published in OJ L 201, 30.7.2008: 2.12, 2.13 (section and overall width), 6.1.1, 6.1.2, 6.1.4 (width tolerances), 6.1.5 (Dmin, Dmax), Annex VI (measurement).
  • ICAT, Ready Reckoner, M1 Category CMVR Type Approval: row 43 "Wheel Guard", IS-13943:1994.
  • Skill-Lync, 2,973 public fender and wheel arch reports, read 22 Nov 2026. scripts/verify/wheel_arch.py recomputes every case another way (bisection on the ray and on the circle angle, the side function on polyline segments, a 0.01° scan for the zone minimum, the rules re-implemented from the text), 544 cases; the page checks itself against it at build time (2,580 checks).
Free counselling

From a wheel arch check to a body design job.

Knowing which number is the law and which is a company margin is what BIW and sheet metal teams ask about in interviews. A Skill-Lync counsellor can map the course that fits the role you want.

Talk to a design course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.