Gas strut calculator
Size the gas struts for a car tailgate, a bonnet (hood), a boot lid or a cabinet lid. Enter the lid's mass, its centre of gravity, the handle, the two strut mounts and the opening angle. You get the F1 force to order and the strut's length and stroke. Free, no sign-up, runs in your browser.
It also shows the angle above which the lid lifts itself and where it stays put or drops shut. You get the hand force to lift and to close it, the load on the latch and the coldest day it still stays open.
Most catalogue formulas check the lid in one position. This one sweeps every angle from closed to fully open, because the worst angle is often somewhere else. Back door and hood design are projects in Skill-Lync's automotive sheet metal design course.
Moments about the hinge at every angle · checked against a virtual-work solution (2891 checks at build) · Stabilus, SUSPA, Bansbach, Lesjöfors, ACE, Camloc · Updated 22 Nov 2026
Lid and hinge · mm from the hinge, lid closed, opening anticlockwise
Strut
Put the hinge at (0, 0) with y up and draw the lid so that it opens anticlockwise, as in the drawing: a tailgate hangs down from the roof, a hood runs to the right. All points are for the closed lid. The strut is taken as fully extended at the full-open angle, its stop. Leave "Your F1" blank and the calculator sizes the strut. Type a catalogue force to check it.
- Needs at least 283 N each (2 struts) (hardest at 100°); with your 20% margin, specify F1 ≈ 339 N and round up to the maker's next size.
- Above 8° the lid rises by itself to full open, where it presses on the stop with 21.2 N at the handle.
- Gas pressure falls in the cold: the struts alone hold the lid fully open down to -29 °C.
- Below 7° the lid's weight beats the struts and friction, so it drops shut by itself.
- Between 7° and 8° the strut's friction lets the lid stay wherever you leave it.
- Pushing it shut takes up to 59 N at the handle (at 50°); lifting it takes up to 21 N (at 0°).
- Strut: 812 mm extended, 545 mm closed, 268 mm stroke. The compressed length leaves 277 mm beyond the stroke for the seal, piston and end fittings.
How to use the gas strut calculator
- Set up the side view. Put the hinge axis at (0, 0), x to the right and y up, with the lid closed. The lid must open anticlockwise, so draw a tailgate hanging down from the roof's rear edge and a hood running to the right of its hinge.
- Enter the lid. Its mass and centre of gravity (CAD gives both; for a quick estimate, use the middle of a uniform panel), the handle where someone lifts or pushes, and the full-open angle.
- Enter the two strut mounts. The lid mount turns with the lid; the body mount is fixed. Their distance at full open becomes the strut's extended length, and how far they move apart becomes its stroke.
- Say from what angle the lid should lift itself, and the coldest temperature at which it must still stay open. The calculator finds the smallest F1 that does both and adds your margin.
- Check a real strut. Type a catalogue F1 and its progression and friction (from the maker's table) into the strut boxes. Then use the angle slider to see what the lid does at each position.
How a gas strut holds a lid up
The lid turns about its hinge, so everything comes down to moments about the hinge. The weight acts at the centre of gravity and closes the lid with the moment m g xG, xG being the horizontal distance from the hinge to the CG. The struts push along their own line. Their moment is the force times the lever arm d, the perpendicular distance from the hinge to that line:
Both sides change as the lid opens. The CG swings over, so xG first grows and then shrinks. The strut's line swings away from the hinge, so d usually grows. The strut also extends, so its force drops. On the example tailgate the lever arm grows from 25.1 mm closed to 170.8 mm fully open, while the weight's leverage changes as the chart above shows.
A gas strut has friction, so it pushes harder when it is being compressed than when it extends:
That band between the two strut curves is why a well-sized lid stays wherever you let go of it over part of its travel. On the example tailgate it drops shut below 7°, floats between 7° and 8°, and lifts itself above 8°.
The catalogue formula, and why this calculator sweeps every angle
Stabilus prints this sizing formula (Lesjöfors, Bansbach and Camloc print the same thing with their own symbols). FG is the weight, LG its lever arm, L1 the strut's lever arm and R a reserve factor:
It is a moment balance in one position. Lesjöfors takes the CG's lever arm in the open position and adds 10-15%, while Stabilus uses a 1.2 to 1.3 reserve factor. The catch is that the hardest angle for the strut is not always the open one: the strut has lost force as it extended, but the CG may still be far from the hinge part-way up. Here is the formula in the open position, against the sweep:
| Lid | Formula, open position (no reserve) | Sweep: least F1 to rise from the set angle | Hardest angle | Strut stroke |
|---|---|---|---|---|
| Tailgate, 25 kg, 2 struts | 283 N | 283 N | 100° | 268 mm |
| Bonnet (hood), 16 kg, 2 struts | 129 N | 322 N | 20° | 123 mm |
| Cabinet lid, 6 kg, 1 strut | 14 N | 206 N | 25° | 86 mm |
For the tailgate the open position is the hardest, so the formula and the sweep agree. For the bonnet and the cabinet lid the struts struggle most low down, at 20° and 25°. There the centre of gravity is still far out from the hinge. By full open it has swung back towards the hinge line, and its leverage is small. A strut sized by the open-position formula would leave these lids sitting low, and even a 1.3 reserve factor would not cover the bonnet's gap of 2.5 times. Sweeping every angle shows it.
The verifier behind this page works the moments a second way, by virtual work: the strut's moment is its force times how fast it lengthens as the lid turns, and the weight's moment is the weight times how fast the CG rises.
F1, F2, progression and friction
Makers describe a strut by four forces on its force-stroke diagram. F1 is the extension force measured 5 mm before the strut is fully extended (10 mm for Stabilus's dynamically damped type) at 20 °C. It is the number on the label and the one you order. F2 is the extension force 5 mm before full compression. F3 and F4 are the forces needed to push it in, and FR = F3 − F1 is the friction.
F2 is higher than F1 because the force comes from nitrogen pressure acting on the rod's cross-section (F = p × A). As the rod goes in, it takes up gas volume and the pressure rises. A thin rod in a fat tube rises little; a thick rod rises more. Stabilus's LIFT-O-MAT range, with its F1 ranges per size:
| Rod / tube (mm) | F1 range | Longest stroke | Progression F2/F1 | Friction FR max |
|---|---|---|---|---|
| 6/15 | 50-400 N | 150 mm | ≈ 1.30 | 50 N |
| 8/19 | 100-800 N | 250 mm | ≈ 1.35 | 60 N |
| 10/22 | 150-1,150 N | 400 mm | ≈ 1.40 | 80 N |
| 14/28 | 500-2,100 N | 500 mm | ≈ 1.50 | 80 N |
The example tailgate's 340 N with 268 mm of stroke needs the 10/22 size (8/19 would carry the force but stops at 250 mm of stroke), with a progression of about 1.40. Progression matters at the closed end, where the strut is pushed fully in:
| Progression F2/F1 | F1 to order | F2 | Lifts itself above | Hand force to close | Closed, at the handle |
|---|---|---|---|---|---|
| 1.20 | 339 N | 407 N | 12° | 47 N | stays shut, 23 N to lift |
| 1.30 | 339 N | 441 N | 9° | 55 N | stays shut, 21 N to lift |
| 1.35 | 339 N | 458 N | 8° | 59 N | stays shut, 21 N to lift |
| 1.40 | 339 N | 475 N | 7° | 64 N | stays shut, 20 N to lift |
| 1.50 | 339 N | 509 N | 6° | 72 N | stays shut, 18 N to lift |
A steeper strut lifts the gate from lower down, which is what customers like, until it beats the weight even when closed. Then the gate pops up as soon as the latch releases, and the latch and seals have to hold that force all the time.
Gas struts in cold and hot weather
The nitrogen is a fixed amount of gas in a fixed volume, so its pressure follows absolute temperature:
Makers quote 3.3% (Bansbach), 3.4% (ACE) and 3.5% (SUSPA, Lesjöfors) per 10 °C, and rate standard struts for −30 °C to +80 °C. For the example tailgate with struts ordered at 340 N:
| Temperature | F1 at that temperature | Struts alone hold it open? | Hand force to close |
|---|---|---|---|
| -30 °C | 282 N | no, 0.243 N short | 32 N |
| -20 °C | 294 N | yes, 4.1 N on the stop | 37 N |
| -10 °C | 305 N | yes, 8.44 N on the stop | 43 N |
| 0 °C | 317 N | yes, 12.8 N on the stop | 49 N |
| 20 °C | 340 N | yes, 21.5 N on the stop | 60 N |
| 40 °C | 363 N | yes, 30.2 N on the stop | 71 N |
| 60 °C | 386 N | yes, 38.8 N on the stop | 83 N |
| 80 °C | 410 N | yes, 47.5 N on the stop | 94 N |
That is why the calculator asks for the coldest temperature the lid must stay open at. At −20 °C the 340 N struts still hold the gate by gas force alone. On a hot day the same gate takes 83 N to push shut. Struts also lose a little gas every year, so an old strut behaves like a new one on a cold day.
Where to mount a gas strut
- Rod down. All the makers ask for it. The oil then sits at the rod seal, which keeps it lubricated and gas-tight, and the end-of-stroke damping works. Camloc puts it as rod down with the lid fully closed, so the rod goes on whichever mount is lower then; the drawing above follows that.
- Let the struts take over 10° to 30° from closed. Camloc's guidance: mount so the strut is near or past its dead centre when the lid is closed. Then the lid stays shut by its own weight and lifts itself once it is raised past that angle. A strut whose line passes through the hinge has no lever arm at all. Too close to that, and it needs a huge force near closed.
- Start the lid mount about one third of the lid's length from the hinge (Camloc calls it an extremely rough guide), and leave about 10 mm of unused stroke so tolerances never bottom the strut before the lid shuts.
- No side loads or twist. Use ball or angle joints so the strut only ever pushes along its axis, and fit struts in pairs on wide lids so the lid does not twist.
Strut length and stroke
The stroke is fixed by the geometry: how far the two mounts move apart from closed to fully open. A strut can't be shorter than its stroke plus the guide, seal, piston and end fittings. In the Stabilus, Lesjöfors and ACE tables the extended length works out at about twice the stroke plus 32 mm (small struts) to 66 mm (Stabilus 6/15). That is our reading of their tables, not a published rule. The example tailgate needs 812 mm extended and 545 mm closed for 268 mm of stroke, well inside that. If your mounts give a stroke longer than half the closed length, move the body mount away from the lid mount.
How hard is the lid to open and close?
The hand force is the net moment divided by the handle's distance from the hinge, assuming you push square to the lid. On the example tailgate it takes 21 N to lift it from closed and up to 59 N to pull it shut. We found no published limit for tailgates or lids. The UK HSE's push-pull guide uses about 200 N (men) and 150 N (women) to start a load moving, and 100 N and 70 N to keep it moving, as screening figures rather than limits. Car makers set their own closing-effort targets.
The "250 N struts" example shows what an undersized strut does. The gate never lifts itself, needs up to 27 N to lift, and creeps down from fully open, held only by friction.
What this calculator does not cover
- Hinge friction, wind, the lid's own flex and seal loads: the weatherstrip pushes a closed door or gate open, and the latch must hold that on top of any strut force.
- Struts with an end-of-stroke lock, adjustable force (valve) or a damped zone, electric struts (spindle drives) and torsion-bar or spring hinges.
- Non-linear force curves: real force-stroke lines bend slightly and have a damped zone at the ends; the calculator draws a straight line from F1 to F2.
- Lids that slide as well as turn (four-bar hood hinges): the calculator assumes one fixed hinge axis.
- The strut's buckling and the strength of the mounting brackets: the body mount load is shown, but the bracket design is up to you.
Placing the hinges, gas struts and latch on a hood or tailgate, and designing the inner and outer panels around them, is everyday work for BIW and closure engineers. Skill-Lync's sheet-metal course has a hood project and a tailgate project.
Frequently asked questions
How do you calculate the gas strut force for a tailgate or lid?
Take moments about the hinge: n struts × force F × the strut's lever arm must beat the weight × the horizontal distance from the hinge to the centre of gravity, at every angle you want the lid to rise. Makers' one-line formula checks one position and adds 20-30%. For the 25 kg example tailgate the sweep needs 283 N per strut.
What do F1 and F2 mean on a gas spring?
F1 is the strut's extension force measured 5 mm before it is fully extended, at 20 °C. It is the number you order by. F2 is the extension force when it is pushed fully in; it is higher because the rod takes up gas volume. F2/F1, the progression, is about 1.3 to 1.5 on Stabilus struts, depending on size.
Should a gas strut be mounted rod up or rod down?
Rod down. Every major maker (Stabilus, SUSPA, Bansbach, Lesjöfors, ACE) says so: the oil inside then sits at the rod seal, which keeps it lubricated and gas-tight, and it gives the end-of-stroke damping. Fix the rod to whichever mount is lower when the lid is shut; on a tailgate strut running down the D-pillar, that is the body end.
Why won't my tailgate stay open in cold weather?
The nitrogen loses pressure as it cools, about 3.3 to 3.5% for every 10 °C. On our example, struts specified at 340 N hold the gate open down to -29.4 °C. Below that only friction holds it. Old struts also lose gas over the years, so a gate that drifts down on cold mornings usually needs new struts.
How long a gas strut do I need?
As long as the distance between its two mounting points with the lid fully open, and with a stroke equal to how far those points move apart from closed to open. Catalogue struts are about twice the stroke plus 32 to 66 mm long. The calculator reads both off your mounting points: the example needs 812 mm extended with 268 mm of stroke.
Why does my lid pop open or slam shut?
Pop-up means the struts beat the weight right from closed. The latch holds the lid shut, and when it is released the lid jumps. Slamming means they are too weak near closed. Camloc suggests mounting so the strut takes over about 10° to 30° from closed. Below that the weight wins and the lid stays shut. Above it, the lid lifts itself.
Related on Skill-Lync
- Student project: design of a car tailgate and its assembly
- Student project: hood design
- BIW design courses compared
- Automotive design courses compared
- Bend allowance calculator (sheet metal flat lengths)
- Vehicle benchmarking calculator: weighted car matrix, Pugh, and the aluminium hood thickness that matches a steel one
- Section modulus calculator
- Weld strength calculator
- All free engineering tools
Sources
- Stabilus, Standard Program catalogue (LIFT-O-MAT): F1 "measured 5 mm before the extension motion ends"; the LIFT-O-MAT size table (F1 ranges, maximum stroke, x = F2/F1, FR = F3 − F1); the sizing formula "F1 = (FG x LG) / (n x L1) x R" with "R: Reserve force factor 1,2 ... 1,3"; standard range −30 °C to +80 °C; "installed rod down". Read 22 Nov 2026.
- SUSPA, gas springs FAQ: "F = p x A"; force changes "by about 3.5% per 10°C"; rod down "to ensure the piston rod seal is lubricated". Read 22 Nov 2026.
- Bansbach easylift, force diagram and measuring points (F1-F4, FR; "For each 10˚C, the force changes by approx 3.3%") and installation advice ("should be installed with the piston rod downwards"; no side forces). Read 22 Nov 2026.
- Lesjöfors, Gas Springs & Fittings catalogue 2024: "F1 = (G x L) / (W x n) + 10 – 15% margin of error", L measured in the open position; stroke and length tables. Read 22 Nov 2026.
- ACE, Industrial Gas Springs catalogue (2016 issue): "An increase of 10 °C will increase force by 3.4 %"; progression "due to the reduction of the internal gas volume". Read 22 Nov 2026.
- Camloc Motion Control in Engineer Live, An introduction to gas spring design (P1/P2 5 mm from the ends), How to mount gas springs effectively, part 1 (moving mount "approximately 1/3 the length of the lid from the hinge") and part 2 (over-centre when closed, crossover "around 10° to 30° from fully closed", "allow 10mm of unused stroke"). Read 22 Nov 2026.
- Lotus Engineering for the ICCT, An Assessment of Mass Reduction Opportunities for a 2017–2020 Model Year Vehicle Program (2010): a steel Toyota Venza tailgate panel 14.49 kg and hood 16.8 kg, without hinges and hardware. The example lids on this page are illustrative, not any particular vehicle. Read 22 Nov 2026.
- UK Health and Safety Executive, Doing a push/pull risk assessment: guideline starting forces of about 200 N (men) and 150 N (women), "should not be regarded as weight limits". Read 22 Nov 2026.
- Skill-Lync, scripts/verify/gas_strut.py: turns the points with complex numbers. It finds the strut's moment as force × dL/dθ and the weight's as m g dyG/dθ by finite differences, the required force on a 200,000-step grid, and the rise and fall angles by bisection. The page compares 2891 numbers with it when it is built.