DRAWING 1     CV JOINT DRAWING 2     QUICK RETURN MECHANISM  

                                                                      BASE BRACKET DESIGN Aim:        To create Base Bracket Design in the function of the Class B and Class C surface and also perform Draft Analysis through the class A surface. Objectives:        Creates proper tooling Axis.        Do proper Draft Analysis.…

                                                                          SWITCH BEZEL DESIGN Aim:           To…

                                                                              BUMPER DESIGN Aim:        …

                                                                                DOOR HANDLE AIM:      …

                                                                          DOOR TRIMS-DOG HOUSE AIM:          …

                                                                          DOOR APPLIQUE-HEAT STAKES AND LOCATORS Aim:      …

                                                                                 A PILLAR MASTER SECTION Aim:  …

                                               DOOR TRIM DESIGN USING MASTERSECTION Aim:       The Creation of CAD model considering Class A Surface,Mastersection and the attachement strategy. Objective:        To creation of CAD model considering Class A Surface,mastersecttion and atttachment strategy.       Create the…

                                                HOOD DESIGN CHALLENGE Introduction:                   The Hood is also called as bonnet.The Hood is the main component of a car and it is located in the front position of the car.Then the Hood makes the car look like stylish and also gives the stylish looks.and then shape…

                                                   Section Modulus of Hood Introduction:                   To find the section modulus of the Hood Designed for analyzing its strength and also want to know the design of difference in the bending strength of Hood.Then the higher of the section modulus of a structure makes…

                                                    FENDER DESIGN Introduction:                      Fender is the part of an automobile (Vehicle Body) that frames the wheel well (fender underside).It is the primary purpose is to prevent sand,mud,rocks,liquids and other road spray from being thrown into the air by the…

                                                         CAR ROOF DESIGN AIM:              To Design and Develop the Roof of the car with its components by following the master sections and the Design parameters. Objective:              1.To create the The Roof Design in NX Cad and also Design the Front Roof Rail,Rear…

                                               Back Door Design Aim:          To Design the Back Door of the car by the given  Surface and also Design the outer panel and the inner panel  by the given surface and design the reinforcements. Objectives:        To Design the inner panel of the car  with design parameters…

                                                  WIRING HARNESS DESIGN Aim:        This project is for study and understand the different models of the connector and the conector clips and covert them innto electrical parts using catia V5.then define all necessary properties and understand the wiring harness design process…

                       WIRING HARNESS ROUTING AND PACKAGING RULES                              (CLIPS,BACKSHELL AND CORRUGATED TUBES) Aim:              To Study and understang the different models of the clips,backshell and corrugated tube and convert the given CAD data file of the P Clamp into Electrical support and BackShell…

                         WIRING HARNESS DESIGN IN CATIA V5-3D MODELLING Aim:           Route the following harness layout in elcectrical workbench.Make assumptions for HArness bundle diameters.Use following connectors as shown in layout diagram. Download connector 3D Data from www.te.com DT06-4S DT06-6S DT06-2S DT06-08SA…

                                       WIRING HARNESS ROUTING Aim:            The aim of the project is to study and understand the given harness layout and by following the layout and design guidelines create two different wiring harness routing set and finally interconnected them by adding it into anew product file using…

                                 WIRING HARNESS FLATTENING Aim:               The aim of the project is to flatten the input file of the wiring harness geometrical bundle set by the following the design guidelines and add the flattened view to the drawing sheet by giving dress up features to the bundles and protective…

                                               WIRING HARNESS ROUTING AND FLATTENING ON V16 ENGINE Aim:       To Design and develop the wire harness routing for the given V16 engine by…

                           WIRING HARNESS ROUTING AND FLATTENING ON THE BACK DOOR Aim:          The project aims to route the wiring harness on the given backdoor of a car and prepare a flattened view drawing in the CATIA V5…

   ASSEMBLY AND APPLY GD AND T TO THE BUTTERFLY VALVE VALVE ASSEMBLY DRAWING   Aim:       The aim of this project is to model a butterfly valve and to apply GD and T to the different parts of the Butterfly Valve and the assembly. Introduction:       A Butterfly Valve is  from…