MODELLING OF HYUNDAI VENUE-SANJEET MARGHADE Title : SOLID MODELLING, SURFACING AND RENDERING OF HYUNDAI VENUE CAR. Objective : The main objective of this project to design and modelling of components of car, using sketch tools and 3D modelling features of Solidworks.Assembly of car using Solidworks assembly tool and Rendering…

objective   To write program on the Robotic Arm. %simulation of Forward kinematics of a 2R Robotic Arm. clc,clear,close all % theta1 is in degree. % theta 1 is the angle of link 1 with respect to x axis Theta1=linspace(0,90,10); %theta 2 is in degree. % theta 2 is the angle of link 2 with respect to x axis Theta2=linspace(0,90,10);…

Program that solves the ODE which represents the equation of motion of a simple pendulum with damping. given:- damping coefficient,mass of ball,length of string,time span,intial angular velocity ,ODE. following code is used while solving ODE and stepwise explanation is given. function [ dtheta_dt ]= ode_func(t,theta,b,g,l,m)%…

Objective :- To write a program to optimize a given function and find global maxima using Genetic algorithem. for this we have to define our stalagmite function and find global maxima . the stepwise explanation of the code is give and the graph and necessery thigs are aatached. Defining function. % defining the stalagmite…

objective:- Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. 1.The file THERMO.dat is opened and read2.Then the 14 co-effs. of polynomials are extracted3. The coefficients are then arranged according to the higher and…

Rankine Cycle Simulator Aim:Creation of Rankine cycle simulator from given input and reading the data from standard thermodynamic library of steam table. Objective : 1. To Simulate a Rankine cycle using matlab.2. Extracting Steam and water properties from XSteam data (IAPWS IF - 97 standard)3. Calculating all the state…

REPORT ON ASSEMBLY OF CHOPPER MODEL DESIGN OF AMERICAN CHOPPER USING SOLIDWORKS OBJECTIVE: - To Design, Assemble and Render the AMERICAN CHOPPER with the help of solidworks INTRODUCTION: - SolidWorks is a solid modelling computer-aided design (CAD) and computer-aided engineering (CAE) application published by Dassault…

1. INTRODUCTION:A yacht is a sail or power vessel used for pleasure, cruising, or racing. There is no standard definition, so the term applies to such vessels that have a cabin with amenities that accommodate overnight use. To be termed a yacht, as opposed to a boat, such a pressure vessel is likely to be at least 33 feet…

UNDER-BODY COATING Automotive Underbody Coatings Underbody coating is a special coating given to the underbody of an automobile. The primary reason the coating is applied is to prevent and reduce corrosion/rusting of the surface, which occurs due to oxidation of the metal. It is also necessary to apply this coating to…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. With draft analysis, you can verify draft angles,…

AIM: The aim of this project is to develop the product design of the switch bezel with the help of the class A surface following the OEM standards. TOOLING AXIS  It is nothing but the direction in which the mold opens and closes the draft angle needed to be provided by considering this tooling axis.We can create…

 Aim: To be able to model solid from the given Class a surface, and perform Draft analysis and create Tooling axis. Tooling Axis: Creating class B surface: Here class B surface is consist of the following elements Base Wall Top wall  Outer Flange Cut section Base and wall:  Base side wall and trimend outer…

AIM: To Create the Core and cavity blocks for the switch bezel component. DESCRIPTION:   CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in two separate pieces,…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION: Tooling Axis: we have tried bisecting method for calculating the tooling axis many times in previous challanges this time while finding the tooling axis i had found the amazing trick which i want to share with you. First i created any…

4 Bar Quick Return Mechanism First we have to create the all parts of this mechanism and then assemble this. Creation of part Slotter: Holder: Slider1: Arm: Slider2: Assembly: CV JOINT First we have to create the all parts of this mechanism and then assemble this. Creation of part CROSS SPIDER: FLANGE: YOKE: ASSEMBLY:…

   DOOR HANDLE Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected. By analysing the component the most easily ejectable direction is somewhere close to the Z…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Given sample design Overview:Initially, we need…

AIM: Create the Dog House for the door trim considering the design rules as mentioned. OBJECTIVE: To design door trim from given class A surface. Designing Class B and Class C surface. Create the Dog House  for the door trim. Perform draft analysis on both class A and final component. Tooling axis creation Generally…

A Pillar Design with master section   Aim :        To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. Objective : Create the required Tooling axis by…

AIM - To prepare a report explaining what is benchmarking, compare at least 4 vehicles and provide a proper conclusion for the report, suggesting a suitable vehicle among the comparison made. BENCHMARKING -  Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those…

Aim: To decide whether the given design passes the European standards or not.   Given Design:   European Regulations Requirement:   Take the outline of the wheel and the fender. Make the centre of the wheel circle. Draw horizontal and vertical perpendicular axes from the centre of the wheel circle.…

Objective: The aim of these project is to design fender and the main design requirements for Drip, Bumper, A pillar, Sill mounting and baffle mounting areas. Fender Fender is a front outer side member of a car which covers the wheel side. Fender purpose is to prevent sand, mud, rocks, liquids and other particles. or Fender…

Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending. Section modulus Section modulus is…

Objective: Devlope and design the given car roof with proper reinforcement by following the master section to creat the roof ditch area, Front roof rail, Rear roof rail and Bow-roofs. Introduction: Roof is a part of an automobile essential to protect and keep the passenger safety from harsh weather condition, accidents…

CAR BACK DOOR DESIGN Aim: To design back door of car using given outer class 'A' surface. What is back door of a car? A door which is located at the rear side of a car which gives access for the boot space to store luggage, spare wheel etc. These doors can be operated manually or electric powered. In most of…

Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)…

 Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 P-clamps lock cables and hoses in place and help ensure that…

Objective:- The objective of this project is to route the harness layout in electrical workbench. Above picture shows the 2D schematic layout of the required harness. The following Deutsch connectors are used in this harness:- DT06-4S (QTY-2) DT06-6S (QTY-1) DT06-2S (QTY-2) DT06-8S (QTY-1) STEP-1 Completely define the…

AIM:   To flatten the wire harness assembly completed in week 7 assignment and place the flattened view on a drawing sheet.   OBJECTIVE:   To flatten the wire harness assembly completed in week 7 assignment. To orient the wire bundle as shown in the layout.     To place the flattened view on a…

AIM-  Route two electrical harnesses as per the given layout and interconnect them as a single harness assembly and then check for bundle continuity, bundle warnings, and then give annotations to the final harness assembly. OBJECTIVE-   The objective of this project is to first route the two Harness…

Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best…

Aim: Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and industry based…

Aim: Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and industry based…

  Aim and Objective: Create a CAD model considering Class A surface as an input, Refer master sections for Nominal thickness, Create the mounting features as per design guidelines in the industry and with master sections, Perform Draft analysis using desired Tooling analysis. Introduction: Design flexibility, Corrosion…