1.  Mix Design for M50 grade concrete without Fly ash Grade designation = M50 type of cement- OPC 43 grades conforming to is 8112 maximum nominal size of aggregate = 20mm minimum cement content: 400kg/m^3(From table of IS 456:2000 exposure condition) maximum water/cement ratio: 0.37 (table 5 of IS 456:2000 exposure…

Aim: - A G+1 floor residential plan, according to Vaastu Shastra. Introduction: -  Vaastu shastra is the ancient Indian science of architecture and act as a guideline to design your home in the way that enhance positive energy. AutoCAD is used to design the G + 1 structure for the project. Procedure: - by using the…

Aim: The geometries from P1 to P2 using all the coordinates system  Introduction: There are two coordinate systems in AutoCAD. World Coordinate System (WCS) and User Coordinate System (UCS) which define the angle of the XY plane you are working in. The WCS should always be used to…

Aim: To draw the figure of C.S of load bearing wall over spread footing. Introduction: The AutoCAD Command line is like a combined control panel and index of all AutoCAD commands you run – and have run – on your drawing. Procedure:  take any point and draw a line with 0.9-unit length (orthomode…

Aim: To draw the figure 1 with the unit taken as a decimal. Introduction: The AutoCAD Command line is like a combined control panel and index of all AutoCAD commands you run – and have run – on your drawing. Procedure:  first take a line of 3unit  then take a line 2.12unit with an angle…

Aim: To create the plan and use proper dimension techniques for 60' * 20' residential building with Vastu shastra Introduction: We can use the text command in auto cad by following some simple steps and use it for mentioning our important data in our drawing. Procedure: first set unit to engineering & put…

AIM: To create a template. Introduction: We can use the text command in auto cad by following some simple steps and use it for mentioning our important data in our drawing. procedure: select the single line text and take any random point  then select the hight & angle and write the letter then select…

AIM: To create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale introduction: Template in AutoCAD is one of such features which help us to reduce our work and to save time. Procedure:  first open drawing then go to layer  then right…

Aim: To create the Kitchen Layout also, use proper dimension techniques. Introduction: We can use the text command in auto cad by following some simple steps and use it for mentioning our important data in our drawing. Procedure: first set unit to decimal & put the precision - 0 then use limits command to set…

Aim: To create a 3D Furniture element Introduction:  AutoCAD is three-dimensional CAD software that is used commercially across the world. Procedure: first take the rectangle command and make the rectangle 2'-6" in the XZ plan  make the rectangle from the end point of 3' in the XY plan  then take the…

Aim: To create a 3D Isometric View of the building Introduction:  AutoCAD is three-dimensional CAD software that is used commercially across the world. Procedure: first make the diagram in the 2d wireframe with the help of line command then make the elevation A & B of the diagram then make it into region…

Aim: - To create a 3-dimensional model of the residential building with a rendered view Introduction: The AutoCAD Command line is like a combined control panel and index of all AutoCAD commands you run – and have run – on your drawing. AutoCAD is three-dimensional CAD software that is used commercially…

1.  AIM: - To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION: - The creation of Ceilings within Revit is a very similar process to that of Floors and Roofs- i.e. You can let Revit do most of the work and “guess” where you want the boundaries…

) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School A) My project is to build multi-unit residential apartments from the given three options.…

1) Using Dynamo create a set of sinusodial points and create a curve and create a surface out of the curve.     AIM:- To create a set of sinusodial points, create a curve and To create a surface out of the curve.     INTRODUCTION:- Dynamo is a visual programming tool that works with Revit. Dynamo extends the power of Revit…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM:- To export the Revit architecture and structure model to Navisworks Cache file following the export settings.…

a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength, or fracture strength, is a material property, defined as the stress in a material just before it yields in a flexure test. Flexural strength represents the highest stress experienced…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures ANSWER--> STATIC ANALYSIS Static analysis can only be performed if the system being simulated does not depend on time, and if the loads being applied are constant. Static analysis doesn't consider inertia. Static refers to the force…

AIM To compute  Ln , Mn and Γn for each of the five modes are to be computed.  To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes. To  obtain the base shear for each of the 5 modes of vibration and the combined base shear as…

AIM: To comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y looking into aspects of symmetry, redundancy and bi-directional stiffness and ductility. INTRODUCTION:- Layout of the framing plan which is shown in figure above concerning earthquake in the two horizontal…

1. STRUCTURE (a) This structure is considered as it is asymmetric. Here cannot be considered as horizontal irregularities and the shear wall shape is like an L. There is some uncertainty concerning certain features of the seismic response of non-rectangular walls. It occurs lack of tensile capacity and force configuration.…

Aim: to model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions. Procedure: Open the ETABS software. Click the file menu and choose to create a new model option. After choosing a new model a dialogue box will appear as model intialization. Choose the…