MODELLING OF AMERICAN CHOPPER IN SOLIDWORKS     INTRODUCTION:                              …

MODELLING AND ASSEMBLY OF SUNSEEKER PREDATOR YACHT       OBJECTIVE : To design individual parts of the yacht with fully defined sketched and appropiorate appearances To assemble all the individual parts of the yacht model by assigning suitable constraints To render the yacht model by adding appearances ,…

                OTTO CYCLE SIMULATOR  USING ENGINE KINEMATICS IN PYTHON     Given  below the program code that can solve the otto cycle and make plots for the thermal efficiency of an engine and generates a pv diagram of it taking in input…

  ANALYSIS OF STRESS AND DEFORMATION IN A PLATE WITH A HOLE AND A PLATE WITH THREE HOLES    OBJECTIVE:          The objective of the analysis is to provide a valid solution for stress at a force on the plate, and to consider which one is the best to go with. In…

STRESS ANALYSIS OF SPUR GEAR USING THREE DIFFERENT MATERIALS     OBJECTIVE :   In this analysis , we are opted to spanalyze for the stress concentration acting up on the spur gear and their behavior ( deformation) upon loads at different time basis ,. and finally recommend…

SOLVING A SECOND ORDER ORDINARY DIFFERENTIAL EQUATION         OBJECTIVE:              To write a program to solve the second order differential equation of simple pendulum under oscillation to find the transient motion of the pendulum under different…

GRID DEPENDENCY TEST ON BEVEL GEAR SIMULATION       AIM :         To perform stress analysis on the bevel gear with grid dependency test of different mesh sizes of 6 mm, 5 mm, 4 mm.     GRID DEPENDENCY TEST:      Generally,…

  RAIL WHEEL TRACK SIMULATION     AIM :             In this simulation , we are going to analyse for the rail wheel subjected on the track by translating loads on the wheel for a displacement of 500 mm and the bearing loads of…

SHEET METAL BENDING ANALYSIS     AIM:       To perform the sheet metal bending in the ANSYS for the various conditions provided and to compare the results with the condition provided.    MODEL:   The provided model has three parts , the…

AIM :   TO PERFORM A CURVE FIT PROGRAM FOR A GIVEN DATA , AND COMPARE WITH THE CURVE GENERATED FROM THE EXPERIMENTAL VALUE CURVE . PROGRAM : import math #we are now importing the math module to perform the mathematical operations import matplotlib.pyplot as plt #we are now importing the matplotlib module to perform…

DATA ANALYSIS ON ENGINE PERFORMANCE     AIM:    TO ANALYSE THE GIVEN SET OF DATA OF THE PERFORMANCE OF AN ENGINE AND TO COMPARE THE ACTUAL DATA AND TO PLOT THE PARAMETERS FROM THE GIVEN DATA SET.    OBJECTIVES:  COMPATIBILITY CHECK:   THE COMPATIBILITY CHECK IS NOTHING…

VERIFICATION OF WELD JOINTS     AIM:           To analyze and stimulate for the verification of the welded joints in the model for three different materials: stainless steel, stainless steel and aluminum alloy (high drought) and brazing using…

COPPER ROLLING OPERATION     AIM:        IN THIS ANALYSIS, WE NEED TO FIND THE PLASTIC DEFORMATION OF THE COPPER ALLOY MATERIAL (WORKPIECE) AND TO PROVE THAT THE DISPLACEMENT OF THE WORKPIECE HAS BEEN DISPLACED TO 90mm.  MODEL:      THE MODEL CONSISTS…

WIRE BENDING     AIM:       To Analyse and simulate the bending of wire using three different materials for three different cases, using a wheel and a lever.  MODEL :         The model consists of one wheel and lever attached with the other…

  SPHERE PRESSING ON A PLATE     AIM:          TO SIMULATE AND ANALYSE FOR THE DEFORMATION OF THE PLATE WHEN A SPHERE BALL MADE TO IMPACT ON IT, IN THIS SIMULATION WE ARE GOING TO CONSIDER ¼ TH OF THE GEOMETRY AND THEN LATER WE ARE USING SYMMTERIC REGION TO MIRROR…

iPhone 6s BENDING SIMULATION AND ANALYSIS     AIM:         To perform a simulation and analysis of an iPhone 6S using two different cases!  and to determine the fatigue life of the material in the iPhone.   Case 1: perform the analysis…

LONG PISTON AND CAM     AIM:        To simulate and analysis for the given 3 cases for the long piston and cam challenge.    MODEL:     The given model consists of barrel and barrel cam followed by a cam follower.       …

UNIVERSAL JOINT     AIM:      TO SIMULATE AND ANALYSE FOR THE UNIVERSAL JOINT PROVIDED WITH THREE DIFFERENT MATERIALS .    MODEL:      THE MODEL CONSISTS OF TWO UNIVERSAL PINS CONNECTED TO A SPRING JOINT AND A JOINT .        MATERIALS: …

WORM GEAR     AIM:       TO SIMULATE AND ANALYSIS FOR THE WORM GEAR AND TO FIND THE STRESS AND STRAIN VALUES ACCORDING TO THE GIVEN CONDITION.    MODEL:      THE MODEL CONSISTS OF A WORM AND A GEAR. HERE WE MADE THE GEAR SPLITTED TO HALF ACCORDING TO THE…

TENSION AND TORSION TEST   AIM:     TO CONDUCT A TENSILE AND TORSION TEST ON THE GIVEN SPECIMEN AND TO INSPECT THE STRESS AND TEMPERATURE CHANGES IN IT.  MODEL:      THE PROVIDED SPECIMEN IS A ROD      MATERIAL:     THE MATERIAL USED HERE…

MACHINING WITH PLANAR SURFACE     AIM:      TO ANALYSE AND SIMULATE FOR THE GIVEN CASE USING THE MACHINING WITH PLANAR SURFACE MODEL.  MODEL:    THE MODEL HAS BEEN PROVIDED WITH WORKPIECE AND THE TOOL.      MATERIAL:      THE MODEL HAS…

BULLET PENETRATING THROUGH A BUCKET   AIM:   TO ANALYZE AND SIMULATE FOR THE PROVIDED MODEL OF BULLET PENETRATING THROUGH A BUCKET FOR THREE DIFFERENT MATERIALS FOR THE BUCKET.  MODEL:   THE MODEL HAS BEEN PROVIDED WITH A BUCKET AND A BULLET. THE BUCKET HAS BEEN SPLITTED INTO TWO PARTS.  MATERIALS: …

CAR CRASH SIMULATION       AIM :  TO PERFORM A CAR CRASH SIMULATION AND TO EVALUATE THE RESULTS USING ONE HALF OF THE CAR BODY WITH THREE DIFFERENT THICKNESS ON THE BODY OF THE CAR .      MODEL:  THE GIVEN MODEL HAS BEEN DIVIDED IN TO HALF OF THE ORIGINAL MODEL. SINCE THE OTHER SIDE…