GATE 2027 Mechanical syllabus: what changed, and what was actually asked
The GATE 2027 ME syllabus is revised: same four sections, but 17 new lines and 13 expanded ones compared with GATE 2026. Below is every syllabus line in IIT Madras's wording, marked where it changed, with how many questions the 6 GATE ME papers from 2022 to 2026 asked on it and links to the solved questions. 11 of the new lines have never been asked in GATE ME; 119 of the 167 lines were the point of at least one question.
Source: ME_GATE2027_Syllabus.pdf, GA_GATE2027_Syllabus.pdf (IIT Madras) and ME_2026_Syllabus.pdf (IIT Guwahati) · 390 questions from GATE ME 2022 to 2026 · Updated 16 Nov 2026
What changed in the GATE 2027 Mechanical syllabus?
IIT Madras revised the ME syllabus for GATE 2027. The four sections are the same, but 17 lines are new and 13 are expanded. The biggest additions are control systems (PID controller, transfer function) and two-degree-of-freedom vibration, belt drives, boiling and condensation, combustion basics, pumps, casting defects, non-destructive testing, PLCs and actuators, work study, six sigma, and quality and reliability. Lagrange's equation and Heisler's charts were dropped. 11 of the new lines have no GATE ME question from 2022 to 2026 to practise from; 6 (stress and strain transformation in 2D, velocity potential, converging and converging-diverging nozzles, crystal structure of common metals, casting defects and six sigma) are new only in wording, and earlier papers already asked them.
| Syllabus line in 2027 | Subject | Change | Asked 2022-26 |
|---|---|---|---|
| Stress and strain transformation in 2D | Mechanics of Materials | New | 2 Q |
| Thin-walled pressure vessels2026: “thin cylinders” | Mechanics of Materials | 4 Q | |
| Free and forced vibration, one and two degrees of freedom2026: “Free and forced vibration of single degree of freedom systems” | Vibrations | 4 Q | |
| Damping estimation and effects2026: “effect of damping” | Vibrations | 4 Q | |
| Vibration isolation and transmissibility2026: “vibration isolation” | Vibrations | none | |
| Control systems: PID controller, transfer function | Vibrations | New | none |
| Belt drives | Machine Design | New | none |
| Velocity potential | Fluid Mechanics | New | 1 Q |
| One-dimensional high-speed compressible flow2026: “basics of compressible fluid flow” | Fluid Mechanics | 1 Q | |
| Converging and converging-diverging nozzles | Fluid Mechanics | New | 4 Q |
| Boiling and condensation | Heat Transfer | New | none |
| Laws of thermodynamics; work, heat and entropy changes2026: “zeroth and first laws of thermodynamics, calculation of work and heat in various processes; second law of thermodynamics” | Thermodynamics | 9 Q | |
| First and second law for closed and open systems2026: “zeroth and first laws of thermodynamics” | Thermodynamics | 3 Q | |
| Combustion basics: air-fuel ratio, equivalence ratio | Thermal Applications | New | none |
| Pumps and pump characteristics | Thermal Applications | New | none |
| Crystal structure of common metals | Engineering Materials | New | 2 Q |
| Metals, alloys, polymers, composites and ceramics2026: “Structure and properties of engineering materials” | Engineering Materials | none | |
| Engineering and true stress-strain diagrams2026: “stress-strain diagrams for engineering materials” | Engineering Materials | 1 Q | |
| Casting defects | Casting, Forming and Joining | New | 1 Q |
| Powder metallurgy2026: “principles of powder metallurgy” | Casting, Forming and Joining | none | |
| Solid-state welding and adhesive bonding2026: “adhesive bonding” | Casting, Forming and Joining | none | |
| Non-destructive testing | Casting, Forming and Joining | New | none |
| Tool geometry: ASA and ORS systems2026: “tool geometry and materials” | Machining and Machine Tools | none | |
| Additive manufacturing processes2026: “additive manufacturing” | Additive Manufacturing | 5 Q | |
| AM products: advantages, limitations, applications | Additive Manufacturing | New | none |
| Pneumatic, electro-pneumatic and hydraulic actuators | CAM and Automation | New | none |
| Programmable logic controllers | CAM and Automation | New | none |
| Work study and productivity | Production Planning and Control | New | none |
| Six sigma | Production Planning and Control | New | 1 Q |
| Quality and reliability | Production Planning and Control | New | none |
Dropped from the 2026 wording: “Lagrange's equation” (Engineering Mechanics). No GATE ME question from 2022 to 2026 needed it. “Heisler's charts” (Heat Transfer). The only transient-conduction question in these papers (2026) was a lumped-system one, and that line stays. “testing of materials with universal testing machine” (Mechanics of Materials). No longer a separate line; the properties it measures (strength, toughness, hardness, impact strength) stay.
Compared word by word against the GATE 2026 ME PDF. Small rewordings that change nothing (for example "integral formula" to "contour integral formula") are not listed; moved lines are marked on the item below.
Which new GATE 2027 ME topics have no previous-year questions?
11 new lines have no GATE ME question from 2022 to 2026. With no ME papers to practise from, read a standard textbook chapter for each and expect one- and two-mark conceptual questions first.
- Control systems: PID controller, transfer function (Vibrations)
- Belt drives (Machine Design)
- Boiling and condensation (Heat Transfer)
- Combustion basics: air-fuel ratio, equivalence ratio (Thermal Applications)
- Pumps and pump characteristics (Thermal Applications)
- Non-destructive testing (Casting, Forming and Joining)
- AM products: advantages, limitations, applications (Additive Manufacturing)
- Pneumatic, electro-pneumatic and hydraulic actuators (CAM and Automation)
- Programmable logic controllers (CAM and Automation)
- Work study and productivity (Production Planning and Control)
- Quality and reliability (Production Planning and Control)
For control systems, the closest past GATE questions are in the GATE Electrical papers: Control Systems: Frequency Response and State Space and Control Systems: Time Response and Stability (25 solved EE questions). The ME line names only the PID controller and transfer functions, so the EE questions on those are the relevant ones.
The other 6 new lines are new only in the wording. Earlier papers already asked them under the broader 2026 lines, so their past questions are a fair guide:
- Stress and strain transformation in 2D: 2 questions (2022 S2, 2026)
- Velocity potential: 1 question (2025)
- Converging and converging-diverging nozzles: 4 questions (2022 S1, 2022 S2, 2023, 2024)
- Crystal structure of common metals: 2 questions (2023, 2026)
- Casting defects: 1 question (2026)
- Six sigma: 1 question (2023)
Which GATE ME syllabus topics are asked the most?
Across the 6 GATE ME papers from 2022 to 2026 (2022 had two sets), the syllabus items with the most marks were laws of thermodynamics; work, heat and entropy changes (13 marks, 9 questions), bulk and sheet forming, load estimation (13 marks, 7 questions), mechanics of machining (12 marks, 6 questions), shear force and bending moment diagrams (12 marks, 6 questions) and displacement, velocity and acceleration of plane mechanisms (11 marks, 6 questions). Asked in every one of the 6 papers: displacement, velocity and acceleration of plane mechanisms and inventory control.
| Syllabus item | Subject | Questions | Marks | Papers asked |
|---|---|---|---|---|
| Laws of thermodynamics; work, heat and entropy changes | Thermodynamics | 9 | 13 | 2022 S1, 2023, 2024, 2025, 2026 |
| Bulk and sheet forming, load estimation | Casting, Forming and Joining | 7 | 13 | 2022 S1, 2022 S2, 2024, 2025, 2026 |
| Mechanics of machining | Machining and Machine Tools | 6 | 12 | 2022 S1, 2022 S2, 2023, 2026 |
| Shear force and bending moment diagrams | Mechanics of Materials | 6 | 12 | 2023, 2024, 2025, 2026 |
| Displacement, velocity and acceleration of plane mechanisms | Theory of Machines | 6 | 11 | 2022 S1, 2022 S2, 2023, 2024, 2025, 2026 |
| Welding, brazing and soldering | Casting, Forming and Joining | 7 | 10 | 2022 S1, 2022 S2, 2023, 2024, 2025 |
| 1D conduction, thermal resistance | Heat Transfer | 6 | 10 | 2022 S1, 2022 S2, 2023, 2024 |
| Friction: belts, brakes, clutches, screw jack, wedge, vehicles | Engineering Mechanics | 6 | 9 | 2022 S1, 2022 S2, 2023, 2024, 2026 |
| Gears and gear trains | Theory of Machines | 6 | 9 | 2022 S1, 2023, 2024, 2025, 2026 |
| Inventory control | Production Planning and Control | 6 | 9 | 2022 S1, 2022 S2, 2023, 2024, 2025, 2026 |
Counted by Skill-Lync: each question of the 6 GATE ME papers (2022 S1, 2022 S2, 2023, 2024, 2025, 2026) filed under the one 2027 syllabus item it mainly tests; marks from the official answer keys.
Which GATE ME syllabus topics were not asked from 2022 to 2026?
37 of the items that were already in the syllabus before 2027 were not the point of any question in the 6 papers, for example mean value theorems, partial and total derivatives, line, surface and volume integrals, higher-order linear ODEs with constant coefficients, initial and boundary value problems and Taylor and Laurent series. The full list is below. Treat it as a reason to give them less time, not to skip them: the syllabus is the contract, and with a revised syllabus the 2027 paper setters may well test what is new.
- Calculus: mean value theorems, partial and total derivatives, line, surface and volume integrals
- Differential Equations: higher-order linear ODEs with constant coefficients, initial and boundary value problems
- Complex Variables: Taylor and Laurent series
- Probability and Statistics: sampling theorems, conditional probability, mean, median, mode and standard deviation
- Engineering Mechanics: virtual work
- Mechanics of Materials: shear centre, strain gauges and rosettes
- Theory of Machines: dynamic analysis of linkages, cams
- Vibrations: vibration isolation and transmissibility, critical speeds of shafts
- Machine Design: design for static and dynamic loading, gears (design), brakes and clutches (design)
- Fluid Mechanics: fluid properties
- Heat Transfer: modes of heat transfer, effect of turbulence
- Thermodynamics: thermodynamic relations
- Thermal Applications: air and gas compressors
- Engineering Materials: metals, alloys, polymers, composites and ceramics
- Casting, Forming and Joining: types of casting processes, plastic deformation and yield criteria, hot and cold working, powder metallurgy, solid-state welding and adhesive bonding
- Machining and Machine Tools: single-point and multipoint cutting tools, tool geometry: ASA and ORS systems
- Metrology and Inspection: comparators, alignment and testing methods, tolerance analysis
- Production Planning and Control: aggregate production planning, lean manufacturing
2 questions tested something the syllabus does not name: 2022 S1 Q.48 (vector algebra: the component of one vector orthogonal to another); 2026 Q.13 (order and degree of a differential equation); they count in the subject totals on the weightage page but not under any item here.
Linear Algebra
8 questions and 12 marks in GATE ME 2022 to 2026. 3 of its 3 syllabus items were asked. Solved questions: Linear algebra.
Official syllabus text
Linear Algebra: Matrix algebra, systems of linear equations, eigen values and eigen vectors.
Linear Algebra: Matrix algebra
systems of linear equations
eigen values and eigen vectors.
Calculus
18 questions and 22 marks in GATE ME 2022 to 2026. 9 of its 12 syllabus items were asked. Solved questions: Calculus and vector calculus.
Official syllabus text
Calculus: Functions of single variable, limit, continuity and differentiability, mean value theorems, indeterminate forms; evaluation of definite and improper integrals; double and triple integrals; partial derivatives, total derivative, Taylor series (in one and two variables), maxima and minima, Fourier series; gradient, divergence and curl, vector identities, directional derivatives, line, surface and volume integrals, applications of Gauss, Stokes and Green's theorems.
Calculus: Functions of single variable, limit, continuity and differentiability
mean value theorems
indeterminate forms
evaluation of definite and improper integrals
double and triple integrals
partial derivatives, total derivative
Taylor series (in one and two variables)
maxima and minima
Fourier series
gradient, divergence and curl, vector identities, directional derivatives
line, surface and volume integrals
applications of Gauss, Stokes and Green's theorems.
- 2024 Q.12 Closed surface integral of z dx dy over a sphere of radius R
- 2023 Q.31 Flux of B = x i + y j − 2z k through the curved surface of a cone (h = 2, r = 3)
- 2022 S2 Q.12 Flux of F = 3x i + 5y j + 6z k out of a unit cube centred at (1, 2, 3)
- 2022 S1 Q.13 Flux of ∇φ, φ = (x² + y² + z²)/2, out of a unit sphere
Differential Equations
9 questions and 16 marks in GATE ME 2022 to 2026. 4 of its 6 syllabus items were asked. Solved questions: Differential equations.
Official syllabus text
Differential Equations: First order equations (linear and nonlinear); higher order linear differential equations with constant coefficients; Euler-Cauchy equation; initial and boundary value problems; Laplace transforms; solutions of heat, wave and Laplace's equations.
Differential Equations: First order equations (linear and nonlinear)
higher order linear differential equations with constant coefficients
Euler-Cauchy equation
initial and boundary value problems
Laplace transforms
solutions of heat, wave and Laplace's equations.
Complex Variables
6 questions and 10 marks in GATE ME 2022 to 2026. 3 of its 4 syllabus items were asked. Solved questions: Probability, statistics and complex variables.
Official syllabus text
Complex Variables: Analytic functions; Cauchy-Riemann equations; Cauchy's integral theorem and contour integral formula; Taylor and Laurent series.
Complex Variables: Analytic functions
Cauchy-Riemann equations
Cauchy's integral theorem and contour integral formula
Taylor and Laurent series.
Probability and Statistics
5 questions and 8 marks in GATE ME 2022 to 2026. 2 of its 5 syllabus items were asked. Solved questions: Probability, statistics and complex variables.
Official syllabus text
Probability and Statistics: Definitions of probability, sampling theorems, conditional probability; mean, median, mode and standard deviation; random variables, binomial, Poisson and normal distributions.
Probability and Statistics: Definitions of probability
sampling theorems
conditional probability
mean, median, mode and standard deviation
random variables, binomial, Poisson and normal distributions.
Numerical Methods
6 questions and 7 marks in GATE ME 2022 to 2026. 3 of its 3 syllabus items were asked. Solved questions: Numerical methods.
Official syllabus text
Numerical Methods: Numerical solutions of linear and non-linear algebraic equations; integration by trapezoidal and Simpson's rules; single and multi-step methods for ordinary differential equations.
Numerical Methods: Numerical solutions of linear and non-linear algebraic equations
integration by trapezoidal and Simpson's rules
- 2026 Q.15 Trapezoidal rule with four intervals for ∫ dx/(1 + x) from 0 to 4: what is m − n?
- 2025 Q.31 Simpson's one-third rule on five tabulated values from x = 0 to 1: what is the integral?
- 2022 S2 Q.13 Simpson's rule with 10 intervals for ∫(4x² + 2x + 6) dx from 1 to 2: what is the percentage error?
single and multi-step methods for ordinary differential equations.
Engineering Mechanics
21 questions and 31 marks in GATE ME 2022 to 2026. 5 of its 6 syllabus items were asked. Solved questions: Engineering mechanics, Theory of machines and vibrations, Machine design.
Official syllabus text
Engineering Mechanics: Free-body diagrams and equilibrium; friction and its applications including rolling resistance, belt-pulley, brakes, clutches, screw jack, wedge, vehicles, etc.; plane trusses and frames; virtual work; kinematics and dynamics of rigid bodies in plane motion; impulse and momentum (linear and angular) and energy formulations.
Engineering Mechanics: Free-body diagrams and equilibrium
- 2024 Q.27 Massless tetrahedron with loads at A along x and at B along y: where must the third load at O point?
- 2024 Q.58 Three-hinged semicircular arch, P = 100 kN and Q = 50 kN: what is the horizontal reaction at B?
- 2022 S2 Q.26 Square plate loaded by a couple, four support layouts: which can hold it in equilibrium?
friction and its applications including rolling resistance, belt-pulley, brakes, clutches, screw jack, wedge, vehicles, etc.
Reworded in 2027. 2027 says rolling resistance where 2026 said rolling friction.
- 2026 Q.48 50 kg block on a 30° incline, μ = 0.3, moving pulley: what hanging mass starts it moving up?
- 2024 Q.59 A band brake, μ = 0.3, band limit 1.5 kN. What is the largest lever force F?
- 2023 Q.34 Belt brake with 270° wrap and μ = 0.3: what is the ratio of the belt tensions T1/T2?
- 2022 S2 Q.30 Rope over a fixed pulley: 200 N lifts 5 discs; how many discs on the other side stop them sliding down?
- and 2 more (2022 S1)
plane trusses and frames
Reworded in 2027. Now plane trusses only.
- 2025 Q.27 Truss with a 1000 N load at A: which member is a zero-force member?
- 2023 Q.17 Four frames of rigid bars and pin joints: which one is non-rigid?
- 2022 S2 Q.47 Frame with a pin in a slot and two forces Q: which members carry no force?
- 2022 S1 Q.49 Pin-jointed structure with 2 kN and 4 kN loads: what is the force in member CI?
virtual work
kinematics and dynamics of rigid bodies in plane motion
- 2026 Q.50 A bar slides down two perpendicular walls at 45°, top end falling at 6 m/s. How fast is its midpoint moving?
- 2025 Q.26 A disc rolls without slipping. What are the velocities of its centre and of the contact point?
- 2022 S1 Q.32 Annular disc with r² = R²/2 hung on a knife edge: find β in T = βπ√(R/g)
impulse and momentum (linear and angular) and energy formulations.
- 2024 Q.24 Ram on two parallel 7 m ropes must hit at 5 m/s: from what angle should it be released?
- 2023 Q.37 2 kg ball dropped 4.9 m onto a fixed 30° incline, perfectly elastic: what is its momentum just after impact?
- 2022 S2 Q.37 1 kg block 0.4 m × 0.3 m on a pin and roller: what minimum impulse topples it?
- 2022 S1 Q.31 0.001 kg mass at 200 cm/s sticks to a pivoted rod 10 cm from O: what is the rod's angular velocity?
- and 1 more (2022 S1)
Mechanics of Materials
30 questions and 53 marks in GATE ME 2022 to 2026. 12 of its 14 syllabus items were asked. Solved questions: Strength of materials.
Official syllabus text
Mechanics of Materials: Stress and strain, elastic constants and their relationships; stress and strain components transformations in 2D; Mohr's circle for plane stress and plane strain; thin-walled pressure vessels; shear force and bending moment diagrams; bending and shear stresses; concept of shear centre; deflection of beams; torsion of circular shafts; Euler's theory of columns; energy methods; thermal stresses; strain gauges and rosettes; Mechanical properties of materials, toughness, hardness, impact strength.
Mechanics of Materials: Stress and strain, elastic constants and their relationships
stress and strain components transformations in 2D
Named for the first time in 2027. It was always needed for Mohr's circle, and earlier papers asked it: see the questions here.
Mohr's circle for plane stress and plane strain
thin-walled pressure vessels
Was thin cylinders; now any thin-walled vessel, so thin spheres count too.
- 2026 Q.51 What internal pressure can a thin cylinder take if the surface strain is limited?
- 2024 Q.57 What is the normal stress on an inclined weld in a thin pressure vessel?
- 2023 Q.40 How do the axial and hoop stresses vary with depth in an open cylindrical tank hung from its rim?
- 2022 S1 Q.52 How much does the wall thickness of a thin cylinder change under internal pressure?
shear force and bending moment diagrams
- 2026 Q.40 How do you draw the SFD and BMD of a cantilever with a point load and an end moment?
- 2026 Q.41 How do you find support reactions in a compound beam with an internal hinge?
- 2025 Q.57 What is the bending moment in a beam loaded by a uniformly distributed moment?
- 2024 Q.41 How do you tell if a beam is statically indeterminate?
- and 2 more (2024, 2023)
bending and shear stresses
concept of shear centre
deflection of beams
torsion of circular shafts
Euler's theory of columns
energy methods
thermal stresses
strain gauges and rosettes
Mechanical properties of materials, toughness, hardness, impact strength.
Reworded in 2027. Was testing of materials (universal testing machine, hardness, impact); now the properties themselves, with toughness added.
Theory of Machines
18 questions and 27 marks in GATE ME 2022 to 2026. 5 of its 7 syllabus items were asked. Solved questions: Theory of machines and vibrations, Engineering mechanics.
Official syllabus text
Theory of Machines: Displacement, velocity and acceleration analysis of plane mechanisms; dynamic analysis of linkages; cams; gears and gear trains; flywheels and governors; balancing of reciprocating and rotating masses; gyroscope.
Theory of Machines: Displacement, velocity and acceleration analysis of plane mechanisms
- 2026 Q.16 A block slides out along a radial slot at 0.2 m/s while the disc turns at 3 rad/s. What is the Coriolis acceleration?
- 2025 Q.60 An offset slider-crank has a 30 mm crank, 50 mm rod and 10 mm offset. What is the stroke?
- 2024 Q.54 A pin on a rotating link slides in a 60° slot of a hinged link. What is the slotted link's angular velocity?
- 2023 Q.38 A rolling wheel drives a bar PQ whose end slides on the floor. What is the bar's angular velocity?
- and 2 more (2022 S2, 2022 S1)
dynamic analysis of linkages
cams
gears and gear trains
- 2026 Q.17 In a five-gear train with a compound pair, which gear is the idler?
- 2026 Q.22 Worm gearsets transmit motion between which kind of shafts?
- 2025 Q.59 Spur gears at 1:2, addendum = 1 module, 15° pressure angle. Fewest pinion teeth with no interference?
- 2024 Q.52 A Levai train: sun fixed (19 T), planet 24 T, internal gear at 20 rev/min. What is the arm speed?
- and 2 more (2023, 2022 S1)
flywheels and governors
balancing of reciprocating and rotating masses
gyroscope.
Vibrations
9 questions and 13 marks in GATE ME 2022 to 2026. 3 of its 6 syllabus items were asked. Solved questions: Theory of machines and vibrations.
Official syllabus text
Vibrations: Free and forced vibration of linear systems with single and two degrees of freedom, damping estimation and effects; vibration isolation, transmissibility ratio; resonance; critical speeds of shafts; Control system, PID controller, transfer function.
Vibrations: Free and forced vibration of linear systems with single and two degrees of freedom
Two-degree-of-freedom systems are new in 2027; every earlier question is single degree of freedom.
- 2025 Q.42 A mass hangs from a cantilever tip that is also held by a spring. What is the natural frequency?
- 2024 Q.55 A mass on a 2k spring, also pulled through a pulley by a spring k. At what driving frequency does it resonate?
- 2023 Q.30 A 20 kg block on two 1000 N/m springs: how long do ten free oscillations take?
- 2022 S2 Q.40 Match damping and forcing conditions to four response histories (resonance, beats, negative damping)
damping estimation and effects
Estimating damping (logarithmic decrement, damping ratio from a decay) is now named; it was already asked most years.
- 2026 Q.18 Critical damping 350 N·s/m, actual 35 N·s/m. What is the logarithmic decrement?
- 2025 Q.35 The damping ratio equals ω_d/ω_n. What is the damping ratio?
- 2024 Q.25 Successive amplitudes 7.75 mm and 7.20 mm, 2 kg mass, 15 Hz. What is the damping coefficient?
- 2022 S2 Q.31 Damping ratio (1/2π) ln 2 and a 4 mm peak in a hammer test. How big is the next positive peak?
vibration isolation, transmissibility ratio
Transmissibility ratio now named.
resonance
critical speeds of shafts
Control system, PID controller, transfer function.
New in 2027: control systems were not in the GATE ME syllabus before, so there are no ME questions to practise from. The GATE EE and IN papers have control-systems questions.
Machine Design
16 questions and 21 marks in GATE ME 2022 to 2026. 6 of its 10 syllabus items were asked. Solved questions: Strength of materials, Machine design.
Official syllabus text
Machine Design: Design for static and dynamic loading; failure theories; fatigue strength and the S-N diagram; principles and design of machine elements such as bolted, riveted and welded joints; shafts, gears, belt drives, rolling and sliding contact bearings, brakes and clutches, springs.
Machine Design: Design for static and dynamic loading
failure theories
- 2026 Q.34 What is the permissible stress for a biaxial state using distortion energy theory?
- 2025 Q.22 Tensile yield stress 200 MPa: what is the shear yield stress by the von Mises criterion?
- 2024 Q.56 What is the factor of safety of a shaft under axial force and torque by distortion energy theory?
- 2023 Q.26 Principal stresses 70, −70 and 0 MPa, yield stress 100 MPa: do the maximum normal stress and maximum shear stress theories predict failure?
- and 1 more (2022 S2)
fatigue strength and the S-N diagram
- 2025 Q.43 Endurance limit = yield strength, load applied and removed, Soderberg with factor of safety 2: what is the maximum stress?
- 2024 Q.26 Soderberg, modified Goodman, Gerber or yield line: which is the most conservative against fatigue failure?
- 2023 Q.18 On the S-N curve of a steel, which level is the endurance limit?
- 2022 S1 Q.29 Surface finish, shot peening, humidity: which of these improve the fatigue strength of a mild steel shaft?
principles and design of machine elements such as bolted, riveted and welded joints
- 2026 Q.21 Plate welded to a gusset with two parallel fillet welds of length l and leg h: what is the critical load?
- 2025 Q.61 10 mm plates, one transverse fillet weld, 5 kN, weld UTS 150 MPa, factor of safety 3: what weld length is needed?
- 2022 S1 Q.40 Two rivets 100 mm apart, P = 10 kN at e = 3√7a, permissible shear 50 MPa: what is the minimum rivet area?
shafts
gears
belt drives
New in Machine Design for 2027 (belt-pulley friction was already in Engineering Mechanics).
rolling and sliding contact bearings
brakes and clutches
springs.
Fluid Mechanics
30 questions and 47 marks in GATE ME 2022 to 2026. 12 of its 13 syllabus items were asked. Solved questions: Fluid mechanics.
Official syllabus text
Fluid Mechanics: Fluid properties; fluid statics, forces on submerged bodies, stability of floating bodies; control-volume analysis of mass, momentum and energy; fluid acceleration; differential equations of continuity and momentum; concept of velocity potential; Bernoulli's equation; dimensional analysis; viscous flow of incompressible fluids, boundary layer, elementary turbulent flow, flow through pipes, head losses in pipes, bends and fittings; One dimensional high speed compressible fluid flow; flow through converging and converging-diverging nozzles.
Fluid Mechanics: Fluid properties
fluid statics, forces on submerged bodies, stability of floating bodies
- 2026 Q.29 A 500 kg load sits on a hydraulic actuator inclined at 60°. What does the oil pressure gauge read?
- 2023 Q.64 Two liquid layers press on a gate hinged at its base. What is the moment about the hinge?
- 2022 S2 Q.62 A wooden rod hinged at the water surface is held under by a lead ball. How big is the ball?
control-volume analysis of mass, momentum and energy
fluid acceleration
differential equations of continuity and momentum
- 2024 Q.16 Use continuity to find the missing velocity component v(x, y).
- 2023 Q.63 Density falls with time in a one-dimensional flow. Use continuity to find u(2, 1).
- 2022 S2 Q.29 V = 4xy î + 2(x² − y²) ĵ: is the flow incompressible, irrotational, one-dimensional?
- 2022 S2 Q.44 From the velocity field of an inviscid flow, find the pressure gradient at (1, 1).
concept of velocity potential
Named for the first time in 2027. Irrotational flow, the condition for a velocity potential to exist, was asked before.
Bernoulli's equation
- 2026 Q.26 Between which two points can Bernoulli's equation NOT be applied?
- 2025 Q.16 Water and engine oil drain from identical tanks at the same head. Which comes out faster?
- 2025 Q.49 A pitot tube on a mercury manometer reads 30 mm in a wind tunnel. How fast is the air?
- 2023 Q.62 Given V = k(x î − y ĵ) and 100 kPa at the origin, what is the pressure at (2 m, 2 m)?
- and 1 more (2022 S2)
dimensional analysis
viscous flow of incompressible fluids
boundary layer, elementary turbulent flow
flow through pipes, head losses in pipes, bends and fittings
One dimensional high speed compressible fluid flow
Was basics of compressible flow; now one-dimensional high-speed flow.
flow through converging and converging-diverging nozzles.
Named for the first time in 2027, but nozzle questions were already asked under the old basics of compressible flow.
- 2024 Q.40 A normal shock stands in the diverging part of a nozzle. How do properties change across it?
- 2023 Q.20 Air at 400 m/s enters a duct whose area doubles. Do velocity and pressure rise or fall?
- 2022 S2 Q.24 Supersonic flow enters a diverging channel, and pressure downstream is higher. Why?
- 2022 S1 Q.30 A convergent nozzle is choked. What happens when the inlet pressure is raised?
Heat Transfer
29 questions and 45 marks in GATE ME 2022 to 2026. 8 of its 11 syllabus items were asked. Solved questions: Heat transfer.
Official syllabus text
Heat Transfer: Modes of heat transfer; one dimensional heat conduction, resistance concept and electrical analogy, heat transfer through fins; unsteady heat conduction, lumped parameter system, thermal boundary layer, dimensionless parameters in free and forced convective heat transfer, heat transfer correlations for flow over flat plates and through pipes; boiling and condensation; effect of turbulence; heat exchanger performance, LMTD and NTU methods; radiative heat transfer, Stefan-Boltzmann law, Wien's displacement law, black and grey surfaces, view factors, radiation network analysis.
Heat Transfer: Modes of heat transfer
one dimensional heat conduction, resistance concept and electrical analogy
- 2024 Q.17 Conductivity rises across a slab as k = A + Bx. What shape is the temperature profile?
- 2024 Q.48 A 20 mm slab generates 100 MW/m³ with faces at 150 °C and 110 °C. Where is the hottest point?
- 2023 Q.28 Insulated rod, no heat generation: which steady temperature profiles are possible?
- 2022 S2 Q.63 A slab with k = CT generates 1280 kW/m³ and both faces are at 600 K. How hot is the centre?
- and 2 more (2022 S1)
heat transfer through fins
unsteady heat conduction, lumped parameter system
thermal boundary layer, dimensionless parameters in free and forced convective heat transfer
- 2026 Q.27 Fluid rises near one vertical plate and falls near the other. How do T₁, T₂ and T₃ compare?
- 2025 Q.15 A ball of ice at −7 °C sits in still air at 30 °C. Which way does the air flow?
- 2022 S2 Q.25 Which non-dimensional term is an estimate of the Nusselt number?
- 2022 S1 Q.25 In the natural convection momentum equation, what does the term gβ(T − T∞) represent?
heat transfer correlations for flow over flat plates and through pipes
- 2025 Q.51 How long must a tube with 2000 W/m² heat flux be to heat 0.01 kg/s of water from 293 K to 353 K?
- 2024 Q.18 The free-stream velocity over a flat plate doubles in laminar flow. By what factor does the Nusselt number change?
- 2024 Q.19 Thermally developing laminar pipe flow (marks to all or not solved)
- 2023 Q.21 Fully developed laminar flow in an isothermal tube: does the Nusselt number depend on Re or Pr?
- and 1 more (2022 S2)
boiling and condensation
New in 2027: not in the 2026 syllabus and not asked in GATE ME 2022 to 2026.
effect of turbulence
heat exchanger performance, LMTD and NTU methods
- 2026 Q.55 A 1 m double-pipe exchanger: inner fluid 20 to 30 °C, outer fluid 60 to 40 °C. What is the heat transfer rate?
- 2024 Q.49 A condenser with 20,000 tubes at 1 kg/s each condenses 430 kg/s of steam at 50 °C. What is its effectiveness?
- 2023 Q.35 Counter-flow exchanger, effectiveness 0.5, C = 1000 and 400 W/K, inlets 300 K and 350 K: what is the heat transfer rate?
- 2022 S2 Q.64 150 kg/s of steam condenses at 200 °C, heating a fluid entering at 100 °C. With ε = 0.9, what is the fluid flow rate?
- and 1 more (2022 S1)
radiative heat transfer, Stefan-Boltzmann law, Wien's displacement law, black and grey surfaces
view factors, radiation network analysis.
- 2026 Q.54 A hot plate radiates to a room and to an insulated plate at right angles. What is the total radiation resistance?
- 2025 Q.48 In a black cylindrical furnace, how much heat does the 800 K bottom radiate to the 500 K curved wall?
- 2024 Q.50 A 6 m hemispherical furnace dome at 1200 K radiates to a black base at 300 K. What is the heat transfer rate?
- 2023 Q.43 A rod inside a cubic enclosure: what is the view factor of the cube's inner surface to itself?
Thermodynamics
19 questions and 29 marks in GATE ME 2022 to 2026. 6 of its 7 syllabus items were asked. Solved questions: Thermodynamics and applications, Heat transfer.
Official syllabus text
Thermodynamics: Thermodynamic systems and processes; properties of pure substances, behaviour of ideal and real gases; zeroth, first and second laws of thermodynamics, calculation of work, heat, energy changes and entropy changes in various processes; application of first and second laws for analysis of closed and open systems; thermodynamic property charts and tables, availability and irreversibility; thermodynamic relations.
Thermodynamics: Thermodynamic systems and processes
properties of pure substances, behaviour of ideal and real gases
zeroth, first and second laws of thermodynamics, calculation of work, heat, energy changes and entropy changes in various processes
Energy and entropy changes in processes are now named alongside work and heat.
- 2026 Q.28 Isothermal expansion of an ideal gas turns all the heat into work. Is that possible?
- 2025 Q.18 Air in a rigid insulated tank is stirred. What happens to its enthalpy and entropy?
- 2025 Q.54 Hydrogen does 400 kJ of work in a polytropic process (n = 1.3). How much heat crosses the boundary?
- 2024 Q.46 Air in a cylinder cools until the piston rests on stops. How much work is done?
- and 5 more (2023, 2022 S1)
application of first and second laws for analysis of closed and open systems
Closed and open system analysis is now named; it was always asked.
- 2022 S2 Q.34 A stirrer does 225 kJ of work on 1 kg of gas in a rigid, insulated tank. What is the final pressure?
- 2022 S2 Q.60 An evacuated tank fills from a 600 kPa air line while losing 1000 kJ of heat. What is the final temperature?
- 2022 S2 Q.61 A steam turbine loses heat reversibly at 500 K. What is its work output?
thermodynamic property charts and tables
availability and irreversibility
thermodynamic relations.
Thermal Applications
13 questions and 23 marks in GATE ME 2022 to 2026. 5 of its 8 syllabus items were asked. Solved questions: Thermodynamics and applications, Fluid mechanics.
Official syllabus text
Applications: Power Engineering: vapour and gas power cycles, concepts of regeneration and reheat; I.C. Engines: Air-standard Otto, Diesel and dual cycles; Basics of Combustion: Air-Fuel Ratio, Equivalence Ratio; Refrigeration and air-conditioning: Vapour and gas refrigeration and heat pump cycles, properties of moist air, psychrometric chart, basic psychrometric processes; Turbomachinery: Impulse and reaction principles, velocity diagrams, Pelton-wheel, Francis and Kaplan turbines, steam and gas turbines, Air and gas compressors, pumps and pump characteristics.
Applications: Power Engineering: vapour and gas power cycles, concepts of regeneration and reheat
- 2026 Q.44 What does the T-s diagram of an ideal regenerative Rankine cycle look like?
- 2025 Q.52 With 90% isentropic efficiency, what is the power output of a 102 kg/s steam turbine?
- 2024 Q.21 Which statement about the Rankine cycle is false?
- 2024 Q.45 What is the efficiency of a Brayton cycle with a regenerator?
- and 1 more (2022 S1)
I.C. Engines: Air-standard Otto, Diesel and dual cycles
Basics of Combustion: Air-Fuel Ratio, Equivalence Ratio
New in 2027: not in the 2026 syllabus and not asked in GATE ME 2022 to 2026.
Refrigeration and air-conditioning: Vapour and gas refrigeration and heat pump cycles
properties of moist air, psychrometric chart, basic psychrometric processes
Turbomachinery: Impulse and reaction principles, velocity diagrams, Pelton-wheel, Francis and Kaplan turbines, steam and gas turbines
Air and gas compressors
Reworded in 2027. Moved from Power Engineering to Turbomachinery.
pumps and pump characteristics.
New in 2027: pumps were not named in the 2026 syllabus.
Engineering Materials
8 questions and 13 marks in GATE ME 2022 to 2026. 3 of its 4 syllabus items were asked. Solved questions: Materials, casting, forming and joining.
Official syllabus text
Engineering Materials: Crystal structure of common metals, phase diagrams, heat treatment; Properties and applications of engineering materials - metals and alloys, polymers, composites and ceramics; Engineering and true stress-strain diagrams.
Engineering Materials: Crystal structure of common metals
Named for the first time in 2027 (2026 said structure and properties of engineering materials), and GATE 2026 already asked an FCC crystal question.
phase diagrams, heat treatment
- 2025 Q.20 Which surface hardening process heats steel to the lowest temperature?
- 2024 Q.28 Which two phases make up pearlite?
- 2023 Q.52 A 1.5% carbon steel is slowly cooled to just below 723 °C. What is the ratio of pro-eutectoid to total cementite?
- 2022 S1 Q.27 Which heat treatments are used for surface hardening of steels?
- and 1 more (2022 S1)
Properties and applications of engineering materials - metals and alloys, polymers, composites and ceramics
Polymers, composites and ceramics are now named, with applications.
Engineering and true stress-strain diagrams.
True stress-strain is now named.
Casting, Forming and Joining
23 questions and 35 marks in GATE ME 2022 to 2026. 6 of its 12 syllabus items were asked. Solved questions: Materials, casting, forming and joining.
Official syllabus text
Casting, Forming and Joining Processes: Different types of casting processes; Patterns, moulds and core; Solidification and cooling, riser and gating design, casting defects; Plastic deformation and yield criteria; Hot working and cold working; Principles of bulk forming and sheet forming processes and estimation of load in these processes; Fundamentals of powder metallurgy and its applications; Principles of welding, brazing, soldering; Solid-state welding processes, adhesive bonding; Non-destructive testing methods.
Casting, Forming and Joining Processes: Different types of casting processes
Patterns, moulds and core
Solidification and cooling
- 2025 Q.34 A 200 mm cube cavity, 7% solidification shrinkage and 8% solid contraction. What is the final edge?
- 2025 Q.62 A cube and a cylinder (D = H) of the same volume are cast. What is the ratio of their solidification times?
- 2024 Q.61 A 20 mm cube and a 20 mm diameter sphere are cast in the same mould material. What is the ratio of their solidification times?
- 2022 S2 Q.19 A 15% B alloy is poured at 800 °C. What is its solidification range on this phase diagram?
riser and gating design
casting defects
Named for the first time in 2027, but GATE 2026 already asked one (dross, scab and scar).
Plastic deformation and yield criteria
Hot working and cold working
Principles of bulk forming and sheet forming processes and estimation of load in these processes
- 2026 Q.59 30% stretching in length gives 15% thinning. What is the sheet's normal anisotropy?
- 2025 Q.39 Ideal wire drawing of a perfectly plastic metal: what is the maximum reduction per pass?
- 2025 Q.41 Can a 30 mm plate be rolled to 27 mm in one pass with 500 mm rolls and μ = 0.12?
- 2024 Q.29 Which metal forming process is earing associated with?
- and 3 more (2024, 2022 S2, 2022 S1)
Fundamentals of powder metallurgy and its applications
Applications of powder metallurgy are now named.
Principles of welding, brazing, soldering
- 2025 Q.21 Which welding process is used to make tailor-welded blanks for cars?
- 2025 Q.33 85% of a 2500 W beam falls within 5 mm and 65% within 3 mm. What is the power density in the ring?
- 2024 Q.32 What electrode material is used to weld low alloy steels by GMAW?
- 2024 Q.63 Arc welding heat loss (marks to all or not solved)
- and 3 more (2023, 2022 S2, 2022 S1)
Solid-state welding processes, adhesive bonding
Solid-state welding (friction, ultrasonic, diffusion, explosive) is new in 2027; adhesive bonding was already there.
Non-destructive testing methods.
New in 2027: not in the 2026 syllabus and not asked in GATE ME 2022 to 2026.
Machining and Machine Tools
16 questions and 26 marks in GATE ME 2022 to 2026. 7 of its 9 syllabus items were asked. Solved questions: Machining, metrology, CNC, CAD and AM.
Official syllabus text
Machining and Machine Tool Operations: Basic machining operations and machine tools; Single-point and multipoint cutting tools; Geometry of single-point turning tools - ASA and ORS systems; Mechanics of machining; Cutting tool materials, tool life and tool wear; Economics of machining; Abrasive machining processes; Principles and applications of non-traditional machining processes; Principles of work holding, jigs and fixtures.
Machining and Machine Tool Operations: Basic machining operations and machine tools
Single-point and multipoint cutting tools
Geometry of single-point turning tools - ASA and ORS systems
The ASA and ORS tool-signature systems are now named.
Mechanics of machining
- 2026 Q.63 Feed 0.24 mm/rev, uncut chip 0.23 mm, Fc 800 N, radial 150 N, shear angle 20°: what is the shear force?
- 2023 Q.44 Shear angle 45°, rake 5°, V = 1 m/s, shear zone 25 μm thick: what is the shear strain rate?
- 2022 S2 Q.54 A 4-tooth slab mill cuts at depth D/2, so the small-depth chip formula fails: what is the maximum cutting force?
- 2022 S2 Q.55 Cutting and thrust forces are equal, rake 0°, shear angle 15°: what is the cutting force?
- and 2 more (2022 S1)
Cutting tool materials, tool life and tool wear
Economics of machining
Abrasive machining processes
Principles and applications of non-traditional machining processes
Principles of work holding, jigs and fixtures.
Additive Manufacturing
5 questions and 7 marks in GATE ME 2022 to 2026. 1 of its 2 syllabus items were asked. Solved questions: Machining, metrology, CNC, CAD and AM.
Official syllabus text
Additive Manufacturing: Principles of different types of additive manufacturing processes for engineering materials; Additively manufactured products – advantages, limitations, and applications.
Additive Manufacturing: Principles of different types of additive manufacturing processes for engineering materials
Was two words under Computer Integrated Manufacturing; now its own topic.
- 2026 Q.31 Which is NOT an STL file error: staircase effect, missing facet, non-manifold topology or degenerate facets?
- 2025 Q.40 Match SLA, FDM, LOM and LENS with their layer technique and material
- 2023 Q.55 Additive manufacturing build time (marks to all or not solved)
- 2022 S2 Q.21 Match FDM, laminated object manufacturing and SLS with their input materials
- and 1 more (2022 S1)
Additively manufactured products – advantages, limitations, and applications.
New in 2027.
Metrology and Inspection
7 questions and 10 marks in GATE ME 2022 to 2026. 5 of its 8 syllabus items were asked. Solved questions: Machining, metrology, CNC, CAD and AM.
Official syllabus text
Metrology and Inspection: Limits, fits and tolerances; Linear and angular measurements; Comparators; Interferometry; Form and finish measurement; Alignment and testing methods; Tolerance analysis in manufacturing and assembly; Principle of coordinate-measuring machine (CMM).
Metrology and Inspection: Limits, fits and tolerances
- 2025 Q.25 Hole 30 +0.030/+0.000 and shaft 30 +0.020/−0.020: loose, interference, transition or clearance fit?
- 2022 S2 Q.20 Shaft 25 −0.04/−0.07 in hole 25 +0.02/−0.00: match allowance, maximum clearance and the hole's MML
- 2022 S1 Q.20 Shaft 25.0 ± 0.010 mm in a hole 25.015 ± 0.015 mm: what type of fit is it?
Linear and angular measurements
Comparators
Interferometry
Form and finish measurement
Alignment and testing methods
Tolerance analysis in manufacturing and assembly
Principle of coordinate-measuring machine (CMM).
CAM and Automation
6 questions and 8 marks in GATE ME 2022 to 2026. 2 of its 4 syllabus items were asked. Solved questions: Machining, metrology, CNC, CAD and AM.
Official syllabus text
Computer Aided Manufacturing and Automation: Basic concepts of CAD/CAM and their integration tools; NC/CNC machines and CNC programming; Pneumatic, electro-pneumatic, and hydraulic actuators for automation; Programmable logic controllers.
Computer Aided Manufacturing and Automation: Basic concepts of CAD/CAM and their integration tools
NC/CNC machines and CNC programming
Reworded in 2027. Moved here from Machining.
- 2024 Q.33 Which letter denotes preparatory functions in CNC part programming?
- 2023 Q.45 A 50-step motor drives a 5 mm pitch screw over 100 mm: how many positions can the table reach?
- 2022 S2 Q.22 Which one cannot give linear motion in a CNC machine: linear motor, ball screw, lead screw or chain and sprocket?
- 2022 S1 Q.19 A stepper needs 600 pulses per revolution on a 5 mm lead screw: what pulse rate moves the table at 5 m/min?
Pneumatic, electro-pneumatic, and hydraulic actuators for automation
New in 2027: not in the 2026 syllabus and not asked in GATE ME 2022 to 2026.
Programmable logic controllers.
New in 2027: not in the 2026 syllabus and not asked in GATE ME 2022 to 2026.
Production Planning and Control
14 questions and 23 marks in GATE ME 2022 to 2026. 5 of its 9 syllabus items were asked. Solved questions: Industrial engineering, Machining, metrology, CNC, CAD and AM.
Official syllabus text
Production Planning and Control: Work study, Productivity, Forecasting models, Aggregate production planning, Scheduling, Materials requirement planning, Six sigma, Lean manufacturing, Inventory Control – deterministic models, safety stock, inventory control systems, Quality and reliability concepts for product lifecycle analysis.
Production Planning and Control: Work study, Productivity
New in 2027.
Forecasting models
- 2026 Q.60 Actual demand 500 then 635, January forecast 250, α = 0.7: what is the March forecast?
- 2025 Q.37 Ten periods of demand and forecast: what are the mean forecast error and the mean absolute deviation?
- 2022 S2 Q.32 January sales were 120 and the forecast was 20 too low: what is February's forecast with α = 0.2?
Aggregate production planning
Scheduling
- 2026 Q.47 On day 20, which jobs have a critical ratio below 1?
- 2024 Q.34 Johnson's rule sequencing (marks to all or not solved)
- 2022 S2 Q.41 Seven parts, milling then polishing: what is the minimum total completion time?
Materials requirement planning
Six sigma
New in 2027.
Lean manufacturing
Inventory Control – deterministic models, safety stock, inventory control systems
Reworded in 2027. Was its own heading; now part of Production Planning and Control.
- 2026 Q.61 Holding cost ₹0.50 per unit per month, ordering cost ₹550, demand 10000 a year: what is the EOQ?
- 2025 Q.64 3000 units a year with price breaks at 500 and 1000 units: what is the minimum total annual cost?
- 2024 Q.38 Ordering 25% more than the EOQ: by what percentage does the total inventory cost rise?
- 2023 Q.13 EOQ model: which curve is total cost, holding cost, setup cost and production cost?
- and 2 more (2022 S2, 2022 S1)
Quality and reliability concepts for product lifecycle analysis.
New in 2027.
Operations Research
12 questions and 21 marks in GATE ME 2022 to 2026. 4 of its 4 syllabus items were asked. Solved questions: Industrial engineering.
Official syllabus text
Operations Research: Linear programming, Simplex method, Transportation, Assignment, Network flow models, Simple queuing models, PERT and CPM.
Operations Research: Linear programming, Simplex method
- 2026 Q.46 Write the dual of a two-variable minimisation LP with four ≥ constraints
- 2024 Q.39 One simplex pivot from a given dictionary: what is the objective at the next basic feasible solution?
- 2023 Q.14 Maximise 45X1 + 60X2 with four constraints: which shaded region is the feasible region?
- 2022 S2 Q.42 Two products, three materials with daily limits: what is the maximum profit per day?
- and 1 more (2022 S1)
Transportation, Assignment, Network flow models
Simple queuing models
PERT and CPM.
- 2026 Q.65 A PERT network of eight activities from node 1 to node 6: what is the expected project length?
- 2025 Q.65 Eight activities A to H: what is the slack of activity D?
- 2022 S2 Q.59 Five activities with optimistic, most likely and pessimistic times: what is the expected project time?
- 2022 S1 Q.42 Eleven activities A to K: what is the latest finish time of activity G?
General Aptitude: Verbal Aptitude
General Aptitude questions in the 6 ME papers on this part: 12 (19 marks). Solved questions: Verbal and logical reasoning.
Official syllabus text
Basic English grammar: tenses, articles, adjectives, prepositions, conjunctions, verb-noun agreement, and other parts of speech. Basic vocabulary: words, idioms, and phrases in context. Reading and comprehension, Narrative sequencing.
Basic English grammar: tenses, articles, adjectives, prepositions, conjunctions, verb-noun agreement, and other parts of speech.
- 2026 Q.1 'The team ___ more than 300 runs in 20 overs ___ rains': scored; despite?
- 2026 Q.6 'People are crowding around ___ pit into which ___ elephant has fallen': which four words fill the blanks?
- 2025 Q.2 Grammatically correct: 'It is I who am / is / are responsible for this fiasco'?
- 2024 Q.6 Prof. P ___ merely a man who narrated funny stories. ___ in his blackest moments… : was/wasn't, Even/Only?
- and 1 more (2023)
Basic vocabulary: words, idioms, and phrases in context.
Reading and comprehension, Narrative sequencing.
- 2025 Q.6 Kolar gold rush sentences P, Q, R, S: which order forms a coherent paragraph?
- 2023 Q.6 Ravi's hardworking, kind friends and his lack of interest in sports: what can be inferred with certainty?
- 2023 Q.8 'I could not bring myself to knock': which sentence order makes a coherent narrative?
- 2022 S2 Q.6 Deep-sea fish with ultra-black skin and lower collagen: what is the correct inference?
- and 1 more (2022 S1)
General Aptitude: Quantitative Aptitude
General Aptitude questions in the 6 ME papers on this part: 26 (41 marks). Solved questions: Quantitative aptitude.
Official syllabus text
Data interpretation: data graphs (bar graphs, pie charts, and other graphs representing data), 2-and 3-dimensional plots, maps, and tables. Numerical computation and estimation: ratios, percentages, powers, exponents and logarithms, permutations and combinations, and series. Mensuration and geometry, Elementary statistics and probability.
Data interpretation: data graphs (bar graphs, pie charts, and other graphs representing data), 2-and 3-dimensional plots, maps, and tables.
- 2026 Q.7 250 items sold at an average of Rs. 60 with S = 2T, R = 3T, Q = 4T: how many of product P?
- 2024 Q.8 Bar chart of VK and RS batting averages 2012-2022: which statement about world cup years is true?
- 2023 Q.3 504 universities and 25951 colleges split into grades by pie charts: what percentage are Grade III?
- 2022 S2 Q.9 One-way trains between four cities: minimum time to go from R to S and back to R?
Numerical computation and estimation: ratios, percentages, powers, exponents and logarithms, permutations and combinations, and series.
- 2026 Q.2 log₂ x + log√2 x = 48: what is x?
- 2025 Q.3 Car P goes north at 25 km/h, car Q east at 30 km/h and stops a while: how long did Q stop?
- 2024 Q.4 x/(pq − r²) = y/(qr − p²) = z/(rp − q²): what is px + qy + rz?
- 2024 Q.7 How many chains A ⊆ B ⊆ C of non-null subsets of {2, 3, 5}? (official key: marks to all)
- and 9 more (2023, 2022 S2, 2022 S1)
Mensuration and geometry
- 2026 Q.8 A semicircular string K on a straight string P: both shortened by x so K becomes a full circle. x/l?
- 2025 Q.9 Arrange isosceles triangle, equilateral triangle, square and circle by number of lines of symmetry
- 2024 Q.10 Angle between faces of a solid made of four equilateral triangles (official key: marks to all)
- 2022 S2 Q.10 Four circles vs nine circles packed in a 1 cm square: ratio of the unshaded areas?
- and 2 more (2022 S1)
Elementary statistics and probability.
General Aptitude: Analytical Aptitude
General Aptitude questions in the 6 ME papers on this part: 14 (18 marks). Solved questions: Verbal and logical reasoning, Quantitative aptitude.
Official syllabus text
Logic: deduction and induction, Analogy, Numerical relations and reasoning.
Logic: deduction and induction
- 2026 Q.4 'All the mangoes in the basket are good' is false: which statement is necessarily true?
- 2026 Q.9 Senator Meritorius, his brother, son and daughter in a 2 x 2 grid: who is the best orator?
- 2022 S2 Q.4 Born on the fifth Monday of February: which statement about that February is correct?
- 2022 S1 Q.4 Four girls learning French, Dutch, Chinese, Japanese and Spanish: who has the most difficult pair?
- and 1 more (2022 S1)
Analogy
Numerical relations and reasoning.
- 2026 Q.5 Four numbers: average 25, each at most 40, each at least 20. Which statements imply which?
- 2025 Q.4 Ceiling and floor functions: which statement is NOT true for every x?
- 2025 Q.7 HIDE is 19-23-7-11 and CAGE is 5-2-17-11: what is the code for HIGH?
- 2024 Q.2 Find the odd one out in {19, 37, 21, 17, 23, 29, 31, 11}
- and 2 more (2024, 2022 S2)
General Aptitude: Spatial Aptitude
General Aptitude questions in the 6 ME papers on this part: 8 (12 marks). Solved questions: Spatial aptitude (picture questions).
Official syllabus text
Transformation of shapes: translation, rotation, scaling, mirroring, assembling, and grouping paper folding, cutting, and patterns in 2 and 3 dimensions.
Transformation of shapes: translation, rotation, scaling, mirroring, assembling, and grouping
- 2025 Q.8 Figure reflected about the horizontal dashed line, then rotated 90° clockwise: which option?
- 2023 Q.10 An opaque square pyramid in a parallel light beam: which shadow P, Q, R or S is not possible?
- 2022 S2 Q.5 Which group of pieces can be assembled into the rocket shape? (official key: B or C)
- 2022 S1 Q.5 Trapezoidal block on a rectangular block: which drawing is the view in the direction of the arrow?
paper folding, cutting, and patterns in 2 and 3 dimensions.
- 2026 Q.3 Grid sequence with a triangle and a circle: what is the next figure?
- 2026 Q.10 Which of the patterns P, Q, R and S generates the repeating figure?
- 2024 Q.9 A paper strip with two V-shaped pieces folded into a closed V-shaped box: how many folds?
- 2023 Q.5 Circle, asterisk, triangle and square in a 4 x 4 grid, once per row, column and 2 x 2 square: which symbol goes in the '?' box?
How many sections are in the GATE ME syllabus?
Four, unchanged for 2027: Engineering Mathematics, Applied Mechanics and Design, Fluid Mechanics and Thermal Sciences, and Materials, Manufacturing and Industrial Engineering. They cover 23 subjects in the official PDF. General Aptitude (15 marks) is common to all GATE papers and has its own syllabus: verbal, quantitative, analytical and spatial aptitude.
Where is the official GATE 2027 ME syllabus PDF?
On the GATE 2027 website run by IIT Madras, under Exam Papers and Syllabus: the file is ME_GATE2027_Syllabus.pdf. This page reproduces its wording item by item, marks what is new against the GATE 2026 PDF, and adds which items were actually asked in GATE ME 2022 to 2026. GATE 2027 runs from 6 to 21 Feb 2027.
Dates, fees, cut-offs and a 12-week plan are in GATE 2027 Mechanical: dates, syllabus and a 12-week plan.
How this page was made
We split the official 2027 syllabus into 179 items (167 ME, 12 General Aptitude), keeping IIT Madras's wording, and compared each line with the GATE 2026 ME PDF to mark what is new or expanded. Then we filed each of the 386 solved questions from the GATE ME papers (2022 S1, 2022 S2, 2023, 2024, 2025, 2026) under the one 2027 item it mainly tests, and the 4 questions without a solution page (marks to all, or not solved) by their topic. A question that needs two topics counts once, under the one that does the work, so read the counts as "how often this was the point of a question". Marks come from the official answer keys; the per-paper subject totals are on the GATE ME weightage page.