GATE Mechanical: Strength of Materials, previous-year questions solved, part 2

Part 2 of 2 of the Strength of Materials hub: 16 more official GATE ME questions on bending and shear stress, deflection, stiffness and energy methods, torsion and springs, columns and buckling and combined stresses and yield, each solved step by step and checked against the official answer key. Part 1 covers stress, strain and material testing, Mohr's circle and stress transformation, thin cylinders and shear force and bending moment.

Questions from official GATE ME papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 16 of 35 questions on this page

GATE 2026 · ME · Q.49NAT · 2 marksBending and shear stress

How do you find the load from the shear stress at the neutral axis of a rectangular beam?

A simply supported beam is subjected to an external point load as shown in the figure below. The beam has a rectangular cross-section of 20 mm × 45 mm. A is a pin support and B is a roller support. The shear stress developed at point C, lying on the neutral axis of the beam, is 3 MPa. Neglecting the mass of the beam, the magnitude of the applied load is _______ kN (rounded off to 1 decimal place).
Simply supported beam of span 5 m: pin A, point C on the neutral axis 1 m from A, load P 2 m from A, roller BABPoint CP1 m1 m3 m

Answer: 3.0 Official key: 2.9 to 3.1

  1. Span 5 m, load 2 m from A: . Point C (1 m from A) is left of the load, so the shear force there is .
  2. For a rectangle, the maximum shear stress (at the neutral axis) is .
  3. , so .
Where this shows up in industry

Short, deep members (brackets, gear teeth, lugs) fail in shear before bending. The 1.5 factor is why FEA shows peak shear at mid-depth, where bending stress is zero.

GATE 2023 · ME · Q.24MSQ · 1 markBending and shear stress

What does the bending stress distribution look like after a beam yields?

A beam is undergoing pure bending as shown in the figure. The stress ()-strain () curve for the material is also given. The yield stress of the material is . Which of the option(s) given represent(s) the bending stress distribution at cross-section AA after plastic yielding?
Beam bent by end moments M into a sagging curve with cross-section A-A at mid-span; elastic-perfectly plastic stress-strain curve that flattens at plus and minus sigma YAAMMσεσY−σY
  1. (A)Linear elastic stress distribution, peak magnitude sigma Y over root 2 at the outer fibresAA−σY/√2σY/√2
  2. (B)Linear elastic stress distribution, peak magnitude sigma Y over 2 at the outer fibresAA−σY/2σY/2
  3. (C)Fully plastic stress distribution: uniform compression sigma Y above the neutral axis, uniform tension sigma Y belowAA−σYσY
  4. (D)Elastic-plastic stress distribution: outer layers at sigma Y, linear elastic core through the neutral axisAA−σYσY

Answer: (C) and (D) Official key: C, D

  1. Plane sections stay plane, so strain varies linearly across the depth: .
  2. The material is elastic-perfectly plastic: up to , then stays at however large the strain.
  3. (A) and (B) are linear with a peak below ( and ): nothing has yielded yet, so they are not post-yield states.
  4. Once the outer fibres reach yield they stay at while an elastic core remains linear: that is (D), the elastic-plastic state.
  5. As the moment rises towards the plastic moment the elastic core shrinks to zero and the stress is in compression above the neutral axis and in tension below: that is (C), the fully plastic state.
  6. Both describe the section after plastic yielding: (C) and (D).
Where this shows up in industry

The fully plastic block distribution in (C) is what gives the plastic moment and the shape factor used in plastic design of steel frames, and it is the state a non-linear FEA run shows at a plastic hinge.

GATE 2023 · ME · Q.58NAT · 2 marksBending and shear stress

How do you find the area moment of inertia of a linearly tapered section by integration?

The area moment of inertia about the y-axis of a linearly tapered section shown in the figure is _____________ m4.

(Answer in integer)
Linearly tapered plane section symmetric about the x-axis: at x = 0 (point O on the y-axis) it spans 1.5 m above and 1.5 m below the axis; at x = 12 m it spans 3 m above and 3 m belowxyO1.5 m1.5 m3 m3 m12 m

Answer: 3024 Official key: 3023.999 to 3024.001

  1. Half-depth grows linearly from 1.5 m at to 3 m at m: , so the full depth is .
  2. A vertical strip of width at distance from the y-axis has area , so .
  3. .
  4. .
Where this shows up in industry

Tapered sections are common in crane jibs, aircraft spars and wind turbine blades. Section properties of such shapes are integrated the same way, strip by strip, in the section calculators that feed beam and shell models.

GATE 2026 · ME · Q.42MCQ · 2 marksDeflection, stiffness and energy methods

How do you find the stiffness and natural frequency of an overhanging beam with a tip mass?

A 5 kg mass is suspended at the free end of an overhanging massless beam, having a pin support and a roller support, as shown in the figure below. Young’s modulus of the material of the beam is 200 GPa and area moment of inertia of the beam is . The natural frequency of the beam in rad/s is
Overhanging beam: pin support, roller support 1 m away, 5 kg mass at the free end 2 m beyond the roller5 kg1 m2 m
  1. (A)10
  2. (B)
  3. (C)5
  4. (D)

Answer: (A) 10 Official key: A

  1. Tip deflection of an overhang beyond a span , load at the tip: .
  2. With , : . , so .
  3. , option (A).
Where this shows up in industry

Every modal analysis is this calculation scaled up: stiffness from the structure, mass from the parts. Mounting a heavy component on a long overhang drops its natural frequency into the range of engine or road excitation.

GATE 2022 · ME Set-2 · Q.51NAT · 2 marksDeflection, stiffness and energy methods

How do you find string tensions on a rigid beam supported by elastic strings?

A rigid beam AD of length is hinged at frictionless pin joint A and supported by two strings as shown in the figure. String BC passes over two small frictionless pulleys of negligible radius. All the strings are made of the same material and have equal cross-sectional area. A force is applied at C and the resulting stresses in the strings are within linear elastic limit. The self-weight of the beam is negligible with respect to the applied load. Assuming small deflections, the tension developed in the string at C is _________ kN (round off to 2 decimal places).
Rigid beam AD hinged at A; string from B over two pulleys down to C; separate string at D; force F at C; spacings aABCDFRigid beamaaaa

Answer: 1.50 Official key: 1.48 to 1.52

The problem is statically indeterminate, so add a compatibility condition.

  1. Let the beam rotate by a small angle about A. Downward movements: B , C , D .
  2. String BC is one string (same tension at B and C) of length ; it stretches by , so its strain is . String D has length and stretches : strain .
  3. Same and : , .
  4. Moments about A: , so and .
Where this shows up in industry

Load sharing between bolts, cables or mounts of different lengths follows this rule: the stiffer path (here the short string D) takes more load. It's why FEA bolt-load results rarely split evenly.

GATE 2022 · ME Set-1 · Q.37MCQ · 2 marksDeflection, stiffness and energy methods

How do you use Castigliano's theorem to find the reaction on an L-shaped frame?

An L-shaped elastic member ABC with slender arms AB and BC of uniform cross-section is clamped at end A and connected to a pin at end C. The pin remains in continuous contact with and is constrained to move in a smooth horizontal slot. The section modulus of the member is same in both the arms. The end C is subjected to a horizontal force and all the deflections are in the plane of the figure. Given the length AB is and length BC is , the magnitude and direction of the normal force on the pin from the slot, respectively, are
L-shaped member: AB of length 4a clamped at A, BC of length a hanging down from B, end C pinned in a smooth horizontal slot, horizontal force P at CAB4aaPC
  1. (A), and downwards
  2. (B), and upwards
  3. (C), and downwards
  4. (D), and upwards

Answer: (A) , downwards Official key: A

  1. The slot stops vertical movement at C, so it applies an unknown vertical force (take upward as positive). Use Castigliano: (bending energy only, slender arms).
  2. Arm BC (distance up from C): , which doesn't depend on .
  3. Arm AB (distance from B towards A): .
  4. .
  5. . The negative sign means it acts downward: , downwards, option (A).
Where this shows up in industry

Energy methods are how hand calculations handle frames that equilibrium can't solve, and they're the basis of the finite element method itself: minimising strain energy gives the stiffness equations.

GATE 2023 · ME · Q.16MCQ · 1 markDeflection, stiffness and energy methods

What is the stiffness of a cantilever beam under a tip load?

The effective stiffness of a cantilever beam of length and flexural rigidity subjected to a transverse tip load is
Cantilever of length L fixed at the left wall with a transverse tip load W at the free endWL
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Tip deflection of a cantilever under a tip load: .
  2. Stiffness is load per unit deflection: .
  3. Options (C) and (D) have units of deflection per unit load (flexibility), not stiffness. Answer: (A) .
Where this shows up in industry

Treating a beam as a spring of stiffness is how a bracket, a sensor mount or a robot link gets turned into one spring in a lumped vibration or stiffness model before anyone builds a full FEA mesh.

GATE 2023 · ME · Q.59NAT · 2 marksDeflection, stiffness and energy methods

How much strain energy is stored in a bar hanging under its own weight?

A cylindrical bar has a length and cross section area . The bar is made of a linear elastic material with a density and Young's modulus . The bar is suspended as shown in the figure and is in a state of uniaxial tension due to its self-weight.

The elastic strain energy stored in the bar equals _________ J. (Rounded off to two decimal places)

Take the acceleration due to gravity as .
Prismatic bar of length L hanging from a rigid ceiling under its own weight, gravity g acting downwardgL

Answer: 2.08 Official key: 2.00 to 2.16

  1. Measure up from the free end. The section at carries the weight below it: , so .
  2. Strain energy: .
  3. .
  4. .
Where this shows up in industry

Self-weight stress decides the design of long hanging members such as mine hoist ropes, drill strings and lift cables, where the top section carries the weight of everything below it before any payload is added.

GATE 2022 · ME Set-2 · Q.50NAT · 2 marksTorsion and springs

How is shear stress shared between the core and rim of a composite shaft in torsion?

A shaft of length is made of two materials, one in the inner core and the other in the outer rim, and the two are perfectly joined together (no slip at the interface) along the entire length of the shaft. The diameter of the inner core is and the external diameter of the rim is , as shown in the figure. The modulus of rigidity of the core and rim materials are and , respectively. It is given that and . When the shaft is twisted by application of a torque along the shaft axis, the maximum shear stress developed in the outer rim and the inner core turn out to be and , respectively. All the deformations are in the elastic range and stress-strain relations are linear. Then the ratio is ______ (round off to 2 decimal places).
Shaft cross-section: inner core of diameter d_i perfectly bonded inside an outer rim of diameter d_odido

Answer: 1.50 Official key: 1.48 to 1.52

  1. Bonded together, core and rim twist by the same angle per unit length , so shear strain is continuous.
  2. Stress . The maximum in each material is at its outer radius: , .
  3. 1.50.

The stiffer core carries the higher peak stress even though it sits closer to the axis.

Where this shows up in industry

Composite drive shafts (carbon tube over a steel or aluminium core) and bimetal shafts are designed this way. The stress jump at the interface is the location that FEA and fatigue checks focus on.

GATE 2026 · ME · Q.19MCQ · 1 markTorsion and springs

What is the maximum shear stress in a closely coiled helical spring?

A closely coiled helical compression spring of mean coil diameter and wire diameter , is loaded by an axial force .
The maximum shear stress developed in the wire is
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. At any wire section the force produces a torque and a direct shear force .
  2. Torsional shear: .
  3. Direct shear: . Both add at the inner side of the coil.
  4. : option (A).

(The Wahl factor would also add curvature; this question asks for the basic direct + torsional sum.)

Where this shows up in industry

Valve springs, suspension coils and clutch springs are sized with this formula plus the Wahl correction. Spring fatigue cracks start on the inside of the coil, where both terms add.

GATE 2023 · ME · Q.60NAT · 2 marksTorsion and springs

How do you find the power transmitted by a shaft from its measured angle of twist?

A cylindrical transmission shaft of length 1.5 m and diameter 100 mm is made of a linear elastic material with a shear modulus of 80 GPa. While operating at 500 rpm, the angle of twist across its length is found to be 0.5 degrees.

The power transmitted by the shaft at this speed is _______kW. (Rounded off to two decimal places)

Take .

Answer: 238.88 Official key: 237 to 240

  1. Angle of twist in radians: .
  2. Polar moment of area: .
  3. Torque from , so . Torsional rigidity: , so .
  4. Power: .
  5. .
Where this shows up in industry

Measuring twist (or surface shear strain with a strain gauge) across a known length of shaft is how torque meters and test-bench shaft power measurements work: the shaft itself is the load cell.

GATE 2022 · ME Set-1 · Q.16MCQ · 1 markColumns and buckling

What is the buckling load of a beam held by an inclined cable?

A uniform light slender beam AB of section modulus is pinned by a frictionless joint A to the ground and supported by a light inextensible cable CB to hang a weight as shown. If the maximum value of to avoid buckling of the beam AB is obtained as , where is the ratio of circumference to diameter of a circle, then the value of is
Beam AB pinned at A to a wall, held at B by a cable to C on the wall at 30 degrees, weight W hanging at BCAB30°W2.5 mg
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Joint B: cable tension at . Vertical: , so . Horizontal: compression in AB .
  2. AB is pinned at both ends (pin at A, cable joint at B): , .
  3. , so and , option (A).
Where this shows up in industry

Jib cranes, boom arms and truss members in compression are checked like this. The geometry (cable angle) decides how much of the hung load becomes column compression.

GATE 2022 · ME Set-2 · Q.18MCQ · 1 markCombined stresses and yield

How do you apply the distortion energy (von Mises) theory to a plane stress state?

A structural member under loading has a uniform state of plane stress which in usual notations is given by , and , where . The yield strength of the material is 350 MPa. If the member is designed using the maximum distortion energy theory, then the value of at which yielding starts (according to the maximum distortion energy theory) is
  1. (A)70 MPa
  2. (B)90 MPa
  3. (C)120 MPa
  4. (D)75 MPa

Answer: (A) 70 MPa Official key: A

  1. Von Mises for plane stress: .
  2. , so .
  3. Yield when : , option (A).
Where this shows up in industry

The 'von Mises stress' plot in every FEA tool is this formula applied at each node. For ductile metals it's the number you compare against yield strength.

GATE 2026 · ME · Q.34NAT · 1 markCombined stresses and yield

What is the permissible stress for a biaxial state using distortion energy theory?

A steel plate having yield strength of 550 MPa, is subjected to biaxial state of stress as and . Using distortion energy theory and considering the factor of safety as 2, the permissible value of that can be applied to the plate is ________ MPa (rounded off to 1 decimal place).

Answer: 103.9 Official key: 102.0 to 105.0

  1. .
  2. Allowable . , so .

Opposite-sign stresses are the worst case: the term adds instead of subtracting.

Where this shows up in industry

Plates under tension one way and compression the other (shear webs, torsion boxes) reach yield much earlier than either stress alone suggests. FEA von Mises plots pick this up automatically.

GATE 2024 · ME · Q.56NAT · 2 marksCombined stresses and yield

What is the factor of safety of a shaft under axial force and torque by distortion energy theory?

A solid massless cylindrical member of 50 mm diameter is rigidly attached at one end, and is subjected to an axial force and a torque at the other end as shown. Assume that the axis of the cylinder is normal to the support. Considering distortion energy theory with allowable yield stress as 300 MPa, the factor of safety in the design is _____ (rounded off to 1 decimal place).
Solid cylinder of 50 mm diameter fixed to a wall at one end, with axial force P and torque T at the free endTP

Answer: 4.5 Official key: 4.3 to 4.7

  1. Axial stress .
  2. Torsional shear at the surface .
  3. .
  4. 4.5.
Where this shows up in industry

Drive shafts with axial thrust (helical gears, propeller shafts) are checked with exactly this combination before fatigue factors are added.

GATE 2022 · ME Set-2 · Q.53NAT · 2 marksCombined stresses and yield

How do you size a shaft for combined bending and torsion using maximum shear stress theory?

A shaft AC rotating at a constant speed carries a thin pulley of radius at the end C which drives a belt. A motor is coupled at the end A of the shaft such that it applies a torque about the shaft axis without causing any bending moment. The shaft is mounted on narrow frictionless bearings at A and B where . The taut and slack side tensions of the belt are and , respectively. The allowable shear stress for the shaft material is 80 MPa. The self-weights of the pulley and the shaft are negligible. Use the value of available in the on-screen virtual calculator. Neglecting shock and fatigue loading and assuming maximum shear stress theory, the minimum required shaft diameter is _______ mm (round off to 2 decimal places).
Shaft AC on bearings at A and B with AB = BC = L; motor torque Mz at A; pulley of radius r at C with belt tensions T1 and T2 both downwardABMzCT1T2rLLzxy

Answer: 23.94 Official key: 23.60 to 24.20

  1. Both belt tensions act downward at C: total 400 N on an overhang of beyond bearing B. Maximum bending moment (at B): .
  2. Torque from the belt: (between A and C).
  3. Maximum shear stress theory: .
  4. Set equal to : , .
Where this shows up in industry

This is the first-pass sizing for any belt- or gear-driven shaft before bearing loads, keyways and fatigue are added, the same numbers you'd later confirm with an FEA of the shaft.

From GATE prep to a CAE career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.