GATE General Aptitude: spatial and picture questions solved (from the official ME papers)
Every GATE paper since 2022 has had one or two General Aptitude questions you answer from a picture alone. The five keyed ME papers from 2022 to 2026 set 6 of them, worth 9 marks: a view of a 3D object, a tangram, paper folding, a reflect-then-rotate figure, a figure series and a repeating pattern. Every figure is redrawn, and every answer was checked by a script: a 3D projection, exact polygons, a face count, symmetry matrices and a cell-by-cell comparison read from the official paper.
Questions from the General Aptitude section of official GATE ME papers (IIT Kharagpur 2022, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); figures redrawn and solutions by Skill-Lync. · Updated 16 Nov 2026 · 6 questions
Trapezoidal block on a rectangular block: which drawing is the view in the direction of the arrow?
Which one of the following is the correct drawing of the view of the 3D object as viewed in the direction indicated by an arrow in the above figure?
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Stand where the arrow is. It points at the right-hand long face of the lower block, so the lower block shows as a wide rectangle. The upper block is seen end-on, so it shows as its cross-section: the trapezoid.
- Which side is it on? The upper block sits at the back corner of the lower block, its vertical face flush with the lower block's back face. Looking along the arrow, the back of the picture is on your right: the trapezoid sits on the right half, its vertical side flush with the right edge.
- Where is the slope? The sloping face looks towards the front of the picture, which is on your left. So the slanted line is on the left of the trapezoid. That is option (A).
- Traps. (C) is the mirror image: the view from the opposite side of the object (the script projects both directions; only the back view puts the slope on the right). (B) runs the slanted edge down through the lower block, but the lower block is a plain box with no sloping edge. (D) draws no upper block at all.
Quick method for any view question: decide which face is nearest you, then for each feature ask only two things: left or right, and does it reach the edge? Two features usually kill three options.
Picking the wrong viewing side is the classic drafting slip: the view from the other end is the mirror image, option (C). It is also why every drawing carries a projection symbol. In first-angle projection (BIS SP 46, the Indian practice) the view from the right is drawn to the left of the front view; in third-angle projection (US practice) it is drawn to the right. Misread the symbol and a hole or chamfer gets machined on the wrong side.
Which group of pieces can be assembled into the rocket shape? (official key: B or C)
- (A)
- (B)
- (C)
- (D)
Answer: (B) or (C): both are accepted Official key: B OR C
- Cut the rocket into pieces you know. Nose: one triangle. Body: one rectangle. The wide base is a trapezoid whose bottom is twice its top, and a trapezoid like that is exactly three equal triangles, point up, point down, point up. So the rocket needs one rectangle and four triangles' worth of area.
- (B) has four triangles and a rectangle: nose + body + the three base triangles. It works.
- (C) works too. Two of the base triangles (one up, one down) together make a parallelogram, so parallelogram + triangle also fill the base, and the other triangle is the nose (drawing below). (B) is the same picture with the parallelogram split into its two triangles.
- (A) has one rectangle and only three triangles: one triangle's area short, whatever you do.
- (D)'s tall thin triangle has a tip of about 23°. No corner of the rocket is that sharp (they are 60°, 150° and 210°), and the 60° and 90° corners of the other pieces can never add up to the angle left over next to that tip. It cannot be placed.
Because two groups work, the official answer key accepts either (B) or (C). If you meet a question like this in the exam, check area first: it rules out the impossible groups in seconds.
A paper strip with two V-shaped pieces folded into a closed V-shaped box: how many folds?
This piece of paper is folded to make the following closed three-dimensional object.
The number of folds required to form the above object is
- (A)9
- (B)7
- (C)11
- (D)8
Answer: (A) 9 Official key: A
- Count the faces of the box. The V outline has 8 edges: two arm ends, the outer and inner sides of each arm, the outer bottom and the inner bottom. So the box has 8 side faces, plus the front and back V faces: 10 faces.
- The rule. The paper is one connected piece. Every fold joins two faces, and you never need a fold that closes a loop (that edge is where the strip's ends meet). A connected piece made of 10 faces therefore has exactly folds: option (A).
- Check it on the paper. The strip wraps once around the 8 side faces: 7 folds between its 8 segments (the 8th corner is the joint where its two ends meet). Each V piece folds onto the strip once: 2 more. .
(B) 7 counts only the strip. (D) 8 counts the joint where the strip closes as a fold, or forgets one V piece. A cross-check from Euler's formula: the box has 16 corners, 24 edges and 10 faces (); a net is cut along edges, and the other are folds.
Sheet-metal designers count folds the same way. In SolidWorks or CATIA sheet metal, a part is unfolded into a flat pattern and every bend is one press-brake stroke; a closed box made from one blank needs (faces − 1) bends, which is why enclosures are often made from two blanks to keep the bend count and tooling simple.
Figure reflected about the horizontal dashed line, then rotated 90° clockwise: which option?
Which one of the following options correctly shows the resultant figure?
Note: The figures shown are representative.
- (A)
- (B)
- (C)
- (D)
Answer: (B) Official key: B
- Track one easy feature, not the whole panel. The crescent's horns point right. Reflecting about a horizontal line leaves left-right alone: still right. Rotating 90° clockwise turns right into down. So in the answer the crescent opens downward. That leaves (B) and (D).
- Use a second feature to split them. Positions: the reflection swaps the rows (the crescent goes from bottom right to top right), then the clockwise turn moves top right to bottom right. The bolt goes top left → bottom left → top left. So the bolt stays top left and the crescent bottom right: option (B).
- What the other options are. (D) is the rotation without the reflection, (C) the reflection without the rotation, and (A) reflection followed by an anticlockwise turn. The script builds all four from the original icons and only (B) matches the asked-for sequence.
Shortcut worth remembering: a reflection followed by a 90° turn is itself a single reflection, here about the diagonal from top left to bottom right. Icons on that diagonal (the bolt, the crescent) stay in their corners; the other two swap.
CAD mirror and rotate commands do not commute: mirror then rotate gives a different part from rotate then mirror. Left-hand and right-hand versions of a bracket or door panel are made with a mirror, and getting the order wrong in an assembly is a classic source of a part that fits only on the other side of the car.
Grid sequence with a triangle and a circle: what is the next figure?
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- The arrow at the top-left corner is the same in every frame, so the grid is not turning; only the shapes move.
- Triangle: column 3, rows 1 → 2 → 3. One row down each step, so next it is in row 4, column 3.
- Circle: column 1, rows 3 → 4 → 1. One row down each step, wrapping from the bottom row back to the top, so next it is in row 2, column 1.
- Triangle row 4 column 3, circle row 2 column 1: option (A).
The script tries every possible shift of the grid (12 of them); only “one row down, wrapping” fits both shapes in all three frames. (D) moves the triangle back to row 1, (B) swaps the two shapes' columns, (C) moves the circle sideways.
Which of the patterns P, Q, R and S generates the repeating figure?
- (A)P
- (B)Q
- (C)R
- (D)S
Answer: (B) Q Official key: B
- Find the repeat. The figure is 36 cells wide and 12 tall, and each tile is 12 by 12, so the figure is one tile placed three times side by side.
- Don't compare whole tiles; compare blocks. Split each tile into a 3 by 3 grid of 4 by 4 blocks. The four tiles agree everywhere except one block each: P differs in the centre block, R in the top-right block and S in the bottom-left block.
- Check those three blocks against the figure: only Q's match. Option (B).
Every cell was read from a high-resolution render of the official paper and Q repeated three times reproduces all 432 cells of the figure; each of P, R and S differs in 8 cells, all inside one block. In the exam, scan one block at a time; looking at the whole tile at once is how people pick the wrong near-copy.
The same block-by-block scan is how inspectors compare a part against its drawing or a PCB against its Gerber: split the area into zones and check one zone at a time, instead of looking for differences across the whole thing at once.