GATE Mechanical: Theory of Machines and Vibrations, previous-year questions solved

Real Theory of Machines and Vibrations questions from the last four GATE Mechanical papers: linkages and velocity analysis, gear trains, flywheels, governors, balancing, gyroscopes, brakes, and free and forced vibration. Each one has a step-by-step solution that matches the official answer key, and a note on where the idea shows up in real engineering work: gearboxes, engines, suspensions, test labs and multibody simulation.

Questions from official GATE ME papers (IIT Kharagpur 2022, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 26 questions

GATE 2022 · ME Set-1 · Q.38MCQ · 2 marksMechanisms and velocity analysis

A four-bar chain with one sliding pair: which links can rotate fully? (Grashof check)

A planar four-bar linkage mechanism with 3 revolute kinematic pairs and 1 prismatic kinematic pair is shown in the figure, where and . The T-shaped link CDEF is constructed such that the slider B can cross the point D, and CE is sufficiently long. For the given lengths as shown, the mechanism is
Four-bar chain with a slider: ground pivots G and F 3 cm apart; crank GA 5 cm; link AB 3 cm perpendicular to the T-shaped link CDEF, with slider B on CE; FD 1.5 cm perpendicular to CEECD1.5 cm3 cm5 cmB3 cmAGF
  1. (A)a Grashof chain with links AG, AB, and CDEF completely rotatable about the ground link FG
  2. (B)a non-Grashof chain with all oscillating links
  3. (C)a Grashof chain with AB completely rotatable about the ground link FG, and oscillatory links AG and CDEF
  4. (D)on the border of Grashof and non-Grashof chains with uncertain configuration(s)

Answer: (A) Official key: A

  1. CE is always 1.5 cm from F () and 3 cm from A (), with F and A on the same side of it. A straight line can sit at those two distances only if A is at least away from F.
  2. A moves on a 5 cm circle about G, and G is 3 cm from F, so the distance FA ranges from to . It never drops below 1.5 cm, so the crank AG can go all the way round without the chain locking.
  3. F lies inside A's circle, so as A goes once round, the direction of FA (and with it the line CE, and AB, which is perpendicular to CE) also turns a full 360°. Every moving link rotates fully relative to the ground FG: a Grashof chain of the kind in option (A).

We checked this by sweeping the crank through 3,600 positions: the chain assembles at every one, and CE turns exactly one full revolution per crank revolution. For a sliding pair, the effective "link length" is the difference of the two offsets ( cm).

Where this shows up in industry

Mechanism designers run exactly this check before detailing a linkage: can the input be driven by a motor that turns continuously, or will it lock at a toggle position? Multibody tools (MSC Adams, SOLIDWORKS Motion, MotionSolve) flag it as a failed assembly or a lock-up partway through the motion study.

GATE 2022 · ME Set-2 · Q.52NAT · 2 marksMechanisms and velocity analysis

A four-bar's 2 cm crank lies along the 10 cm ground line at 5 rad/s. How fast is the 4 cm rocker turning?

In the configuration of the planar four-bar mechanism at a certain instant as shown in the figure, the angular velocity of the 2 cm long link is . Given the dimensions as shown, the magnitude of the angular velocity of the 4 cm long link is given by ________ rad/s (round off to 2 decimal places).
Four-bar mechanism: crank 2 cm lying along the 10 cm ground line, coupler 5 cm, rocker 4 cm; crank angular velocity omega2 = 5 rad/s2 cm5 cm4 cm10 cmω₂ω₄

Answer: 1.25 rad/s Official key: 1.24 to 1.26

  1. Use instantaneous centres. and are the two ground pivots; lies on the line through them (the ground line) and also on the coupler line through and .
  2. The crank lies along the ground line, so (the crank pin) is itself on the ground line. The two lines meet there: is at the crank pin, 2 cm from and cm from .
  3. so .

No angles were needed. The script confirms it by solving the linkage positions numerically and differentiating the rocker angle.

Where this shows up in industry

Instant centres give a quick velocity ratio at any pose, and a velocity ratio is a mechanical advantage. That is how designers size the toggle clamps, wiper linkages and suspension rocker arms where force is multiplied near a dead-centre position.

GATE 2025 · ME · Q.60NAT · 2 marksMechanisms and velocity analysis

An offset slider-crank has a 30 mm crank, 50 mm rod and 10 mm offset. What is the stroke?

An offset slider-crank mechanism is shown in the figure below. The length of the stroke of the slider is ________ mm (rounded off to nearest integer).
Offset slider-crank: crank 30 mm, connecting rod 50 mm; the slider pin moves along a line 10 mm above the crank pivot30 mm50 mm10 mm

Answer: 62 mm Official key: 61 to 63

  1. The slider's extreme positions are where the crank and rod are in line: fully stretched out () and folded back ().
  2. The slider pin is 10 mm off the crank-pivot line, so horizontal distances are: and .
  3. Stroke ( mm).

Ignoring the offset gives , outside the key. Offset makes the stroke longer than twice the crank, and it also makes the mechanism quick-return.

Where this shows up in industry

Engine designers offset the piston pin (or the whole crank) by about a millimetre to cut piston slap and side-thrust friction. Packaging-machine designers use large offsets on purpose to get a quick-return stroke.

GATE 2026 · ME · Q.50NAT · 2 marksMechanisms and velocity analysis

A bar slides down two perpendicular walls at 45°, top end falling at 6 m/s. How fast is its midpoint moving?

A rigid slender bar, AB, is sliding against two mutually perpendicular frictionless walls, as shown in the figure below. The velocity of A in the downward direction at a given instant is 6 m/s. At that instant, the magnitude of absolute velocity of the midpoint G is ________ m/s (rounded off to 2 decimal places).
Rigid bar AB with end A on a vertical frictionless wall and end B on the frictionless floor, at 45 degrees to the floor; A moves down with velocity vA; G is the midpointGABvA45°

Answer: 4.24 m/s Official key: 4.20 to 4.29

  1. The bar keeps a fixed length: , so . At 45°, , so B moves right at the same 6 m/s that A moves down.
  2. G is the midpoint, so its velocity is the average of the end velocities: (3 m/s right, 3 m/s down).
  3. .

Using the instantaneous centre gives the same answer: it sits at the corner opposite the wall junction, at distance from G.

Where this shows up in industry

This is the classic "sliding ladder" constraint, and it is the kinematics of an elliptic trammel and of a scissor-lift arm. Robot path planners use the same geometric differentiation to turn joint speeds into tool speeds (the Jacobian).

GATE 2025 · ME · Q.26MCQ · 1 markMechanisms and velocity analysis

A disc rolls without slipping. What are the velocities of its centre and of the contact point?

A rigid circular disc of radius (in m) is rolling without slipping on a flat surface as shown in the figure below. The angular velocity of the disc is (in rad s−1). The velocities (in m s−1) at points and , respectively, are
Disc of radius r rolling without slipping on flat ground, angular velocity omega clockwise; O is the centre and A the contact point; i points right and j upOrAωĵî
  1. (A) and
  2. (B) and
  3. (C) and
  4. (D) and

Answer: (A) Official key: A

  1. Rolling without slipping means the contact point A has zero velocity: it is the instantaneous centre.
  2. The disc turns clockwise (as drawn), so the centre O, a distance above A, moves to the right at : .
  3. So the answer is and : option (A). (B) has the wrong direction for a clockwise roll, and (C) and (D) give the contact point a velocity, which would be slipping.
Where this shows up in industry

Wheel-slip detection in ABS and traction control compares wheel speed × rolling radius with vehicle speed. When they differ, the contact patch is no longer at rest and the tyre is slipping.

GATE 2026 · ME · Q.16MCQ · 1 markMechanisms and velocity analysis

A block slides out along a radial slot at 0.2 m/s while the disc turns at 3 rad/s. What is the Coriolis acceleration?

A horizontal disk has a radial frictionless slot in which a small block is confined to slide. The disk turns anticlockwise about its centre with a constant angular velocity of 3 rad/s. If the block slides along the slot with a constant speed of 0.2 m/s relative to the slot, then the magnitude of Coriolis acceleration in m/s2 is
  1. (A)1.2
  2. (B)0.6
  3. (C)2.4
  4. (D)0.3

Answer: (A) Official key: A

  1. The Coriolis term appears whenever a point moves relative to a rotating body: .
  2. , at right angles to the slot. Option (A).

Forgetting the factor 2 gives 0.6 (option B), the most common slip.

Where this shows up in industry

Coriolis acceleration loads the sliding blocks of quick-return mechanisms and the followers of rotating cams. It is also the operating principle of Coriolis flow meters and of the MEMS gyroscopes in every phone and in automotive stability control.

GATE 2022 · ME Set-1 · Q.53NAT · 2 marksGears and gear trains

An epicyclic train with the sun fixed and the 80-tooth ring at 900 rpm. How fast does the arm turn?

A schematic of an epicyclic gear train is shown in the figure. The sun (gear 1) and planet (gear 2) are external, and the ring gear (gear 3) is internal. Gear 1, gear 3 and arm OP are pivoted to the ground at O. Gear 2 is carried on the arm OP via the pivot joint at P, and is in mesh with the other two gears. Gear 2 has 20 teeth and gear 3 has 80 teeth. If gear 1 is kept fixed at 0 rpm and gear 3 rotates at 900 rpm counter clockwise (ccw), the magnitude of angular velocity of arm OP is ________ rpm (in integer).
Epicyclic gear train: sun gear 1 fixed at the centre O, planet gear 2 (20 teeth) on arm OP meshing with the sun and with internal ring gear 3 (80 teeth) rotating at 900 rpm counter-clockwiseOPGear 1(0 rpm)Gear 2: planet, 20 teethGear 3: ring, 80 teeth,900 rpm ccwarm OP

Answer: 600 rpm Official key: 600 to 600

  1. Same module for all three gears, so the radii fit: , giving teeth.
  2. Relative to the arm, the train is an ordinary one from sun to ring: (the internal ring turns opposite to the sun).
  3. With : , so and , counter-clockwise like the ring.
Where this shows up in industry

Fixed sun, ring input and carrier output is one of the planetary modes of an automatic transmission. The same compact layout gives the large reductions in EV e-axles and wind-turbine gearboxes.

GATE 2024 · ME · Q.52NAT · 2 marksGears and gear trains

A Levai train: sun fixed (19 T), planet 24 T, internal gear at 20 rev/min. What is the arm speed?

The Levai type-A train illustrated in the figure has gears with module mm/tooth. Gears 2 and 3 have 19 and 24 teeth respectively. Gear 2 is fixed and internal gear 4 rotates at 20 rev/min counter-clockwise. The magnitude of angular velocity of the arm is ________ rev/min. (rounded off to 2 decimal places)
Levai type-A train drawn as a front view: fixed sun gear 2 (19 teeth), planet gear 3 (24 teeth) carried by arm 1, internal gear 4 rotating at 20 rev/min counter-clockwise2 (fixed, 19 T)3 (24 T)4 (internal)20 rev/min ccw1 (arm)m = 8 mm

Answer: 15.58 rev/min Official key: 15.00 to 16.00

  1. Gear 3 meshes with both the sun 2 and the internal gear 4, so the pitch radii fit: teeth. (The module only sets the size and drops out.)
  2. Relative to the arm:
  3. With : .

The figure in the paper is a side view, so the note "internal gear 4" is the key fact: it fixes from the other two gears.

Where this shows up in industry

This is the tabular (or relative-velocity) method that gearbox engineers use for every planetary stage. Simulation tools such as Romax or KISSsoft calculate the same speed ratios before they check tooth stresses and bearing lives.

GATE 2025 · ME · Q.59NAT · 2 marksGears and gear trains

Spur gears at 1:2, addendum = 1 module, 15° pressure angle. Fewest pinion teeth with no interference?

A pair of spur gears is required to maintain a velocity ratio of 1:2. The module of the gears is 10 mm and the addendum is 10 mm. If the operating pressure angle is 15°, the minimum number of teeth required on the pinion to ensure NO interference/undercutting is ________ (answer in integer).

Answer: 25 Official key: 25 to 25

  1. Interference starts when the gear's addendum circle reaches past the point where the line of action touches the pinion's base circle (the interference point).
  2. For gear ratio and addendum module, the minimum pinion teeth are
  3. ; ; .
  4. , so the pinion needs at least 25 teeth.

The script also checks the geometry directly: with 24 teeth the gear's addendum circle reaches past the interference point, and with 25 it does not.

Where this shows up in industry

This is why 14.5° and 15° pressure angles are rarely used in new designs: at this ratio they need 25 or more pinion teeth. At 20° the limit for this ratio drops to about 15 teeth, and designers use profile shift when they want fewer teeth still.

GATE 2026 · ME · Q.17MCQ · 1 markGears and gear trains

In a five-gear train with a compound pair, which gear is the idler?

A gear train with five gears is shown in the figure below. The number of teeth on each gear is , , , , and . The idler gear in this gear train is
Gear train of five gears: gear 1 (driver) meshes with gear 2; gear 3 is on the same shaft as gear 2 and meshes with gear 4; gear 4 meshes with gear 5 (driven)12345N₁ (driver)N₂, N₃N₄N₅ (driven)
  1. (A)gear 4
  2. (B)gear 2
  3. (C)gear 3
  4. (D)gear 1

Answer: (A) Official key: A

  1. Gears 2 and 3 share a shaft (a compound pair), so they turn together.
  2. Speed ratio: cancels.
  3. Gear 4 is driven by gear 3 and drives gear 5. It changes the direction of rotation but not the ratio: it is the idler, option (A).
Where this shows up in industry

Idlers bridge a gap between shafts or flip direction. The reverse gear in a manual gearbox is an idler slid into mesh. They add a mesh, so they also add some noise and about 1-2% loss.

GATE 2026 · ME · Q.22MCQ · 1 markGears and gear trains

Worm gearsets transmit motion between which kind of shafts?

Worm gearsets are used for transmitting rotary motion between
  1. (A)non-parallel and non-intersecting shafts
  2. (B)intersecting shafts
  3. (C)parallel shafts
  4. (D)non-parallel and intersecting shafts

Answer: (A) Official key: A

  1. A worm and wheel connect shafts that are usually at 90° and offset from each other: they neither run parallel nor meet.
  2. That is option (A). Intersecting shafts (B, D) use bevel gears; parallel shafts (C) use spur or helical gears.
Where this shows up in industry

Worm drives give 10:1 to 100:1 in one stage and can be self-locking, which is why they are used in lifts, hoists, gate operators and steering boxes. The price is sliding friction: efficiency is often only 50-90%, falling as the ratio rises.

GATE 2024 · ME · Q.23MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

An engine's energy fluctuation is 300 J and it runs between 220 and 280 rad/s. What flywheel inertia gives a 0.05 fluctuation coefficient?

The change in kinetic energy of an engine is 300 J, and minimum and maximum shaft speeds are rad/s and rad/s, respectively. Assume that the torque-time function is purely harmonic. To achieve a coefficient of fluctuation of 0.05, the moment of inertia (in kg.m2) of the flywheel to be mounted on the engine shaft is
  1. (A)0.113
  2. (B)0.096
  3. (C)0.071
  4. (D)0.053

Answer: (B) Official key: B

  1. The mean speed is .
  2. Energy fluctuation and speed fluctuation: .
  3. : option (B).

The 220-280 rad/s band only fixes the mean speed. Using it as the fluctuation itself () gives 0.020, which is no option. The 0.05 coefficient is the target the flywheel has to achieve.

Where this shows up in industry

Single-cylinder engines, punch presses and reciprocating compressors all need a flywheel to ride through an uneven torque. Dual-mass flywheels in diesel cars split the inertia across a spring to keep crankshaft fluctuations out of the gearbox.

GATE 2022 · ME Set-1 · Q.17MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

A Watt governor runs at h = 400 mm. What is h if the speed doubles?

The figure shows a schematic of a simple Watt governor mechanism with the spindle rotating at an angular velocity about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot is denoted by . The value of mm at a certain . If is doubled, the value of will be ________ mm.
Watt governor: spindle O1O2 rotating at omega about a vertical axis; arms of length l1 from pivot O1 to balls P and S, links l2 to the sleeve QR; h is the height of O1 above the plane of the ballsO₁ωPSQRSleeve (QR), O₂l₁l₁l₂l₂hg = 9.8 m/s²
  1. (A)50
  2. (B)100
  3. (C)150
  4. (D)200

Answer: (B) Official key: B

  1. With massless links and sleeve, only the balls matter. Take moments about for one ball at radius and height below it: .
  2. So . The arm length and ball mass drop out.
  3. : doubling divides by 4, so . Option (B).

At mm the speed is , about 47 rpm. That is why simple Watt governors only work at low speeds: at higher speeds becomes tiny and the governor loses sensitivity.

Where this shows up in industry

Watt governors controlled steam engines. The same balance of centrifugal force and gravity (or a spring) still works in mechanical diesel injection-pump governors, centrifugal clutches and overspeed trips on turbines.

GATE 2022 · ME Set-2 · Q.39MCQ · 2 marksFlywheels, governors, balancing, gyroscope and brakes

Two 1 kg masses at 1 cm and 90° apart: at what radius does a √2 kg mass balance them?

A rigid body in the X-Y plane consists of two point masses (1 kg each) attached to the ends of two massless rods, each of 1 cm length, as shown in the figure. It rotates at 30 RPM counter-clockwise about the Z-axis passing through point O. A point mass of kg, attached to one end of a third massless rod, is used for balancing the body by attaching the free end of the rod to point O. The length of the third rod is ________ cm.
Two 1 kg point masses on massless rods 1 cm long, 90 degrees apart, rotating at 30 RPM counter-clockwise about point O in the X-Y planeXY1 kg1 kg1 cm1 cm90°30 RPMO
  1. (A)1
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Balance means the vector sum of is zero (the speed, 30 RPM, does not matter).
  2. The two masses give 1 kg·cm each at 90° apart, a resultant of .
  3. The balancing mass must supply kg·cm in the opposite direction: , so . Option (A).
Where this shows up in industry

Every tyre change ends on a wheel balancer, which finds the imbalance and asks for a clip-on weight at the right angle. Fans, rotors and crankshafts are balanced the same way, usually in two planes as in the next question.

GATE 2025 · ME · Q.29MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

Balancing: which is true for a rigid rotor and for a single-cylinder engine?

In the context of balancing of rotating and reciprocating masses, which one of the following options is true?
  1. (A)An unbalanced rigid rotor can be completely balanced using a single balancing mass
  2. (B)An unbalanced rigid rotor can be completely balanced using two balancing masses attached in two distinct planes
  3. (C)A single-cylinder internal combustion engine can be completely balanced using a single balancing mass
  4. (D)A single-cylinder internal combustion engine can be completely balanced using two balancing masses

Answer: (B) Official key: B

  1. A rigid rotor with masses spread along its length has an unbalanced force and an unbalanced couple. One mass can cancel the force but not the couple. Two masses in two planes can cancel both: (B) is true, and (A) is false.
  2. A single-cylinder engine's reciprocating mass gives a shaking force along the line of stroke that varies as (primary) and (secondary). Rotating counterweights on the crank produce a force of constant size that turns with it. They can only move part of the primary force to the perpendicular direction, never cancel it completely. So (C) and (D) are false.
Where this shows up in industry

Two-plane balancing is the standard production test for crankshafts, motor rotors and turbine spools. Single-cylinder motorcycles and lawn-mower engines carry a counterweight of about 50% of the reciprocating mass and accept some vibration. Many add a geared balance shaft.

GATE 2026 · ME · Q.20MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

An aircraft engine rotor (1 kg·m², 500 rpm) turns on a 2 km radius at 1200 km/h. What is the gyroscopic moment?

The rotor of an aeroplane engine has a mass moment of inertia 1.0 kg m2. The engine rotates at a speed of 500 RPM in the clockwise direction if viewed from the front of the aeroplane. If the aeroplane while flying at 1200 km/hr turns with a radius of 2 km at same elevation, then the magnitude of the gyroscopic moment exerted by the rotor on the aeroplane structure in N m is
  1. (A)8.73
  2. (B)17.46
  3. (C)4.37
  4. (D)26.19

Answer: (A) Official key: A

  1. Spin: .
  2. Precession (the turn rate): .
  3. Gyroscopic couple: . Option (A).

The direction (nose up or down) depends on the turn direction and the spin sense. The question asks only for the magnitude.

Where this shows up in industry

The same couple loads ship turbines when the hull pitches, motorcycle wheels when a rider leans into a turn, and the bearings of wind-turbine rotors when the nacelle yaws. Designers size those bearings for it.

GATE 2024 · ME · Q.59NAT · 2 marksFlywheels, governors, balancing, gyroscope and brakes

A band brake, μ = 0.3, band limit 1.5 kN. What is the largest lever force F?

A band brake shown in the figure has a coefficient of friction of 0.3. The band can take a maximum force of 1.5 kN. The maximum braking force () that can be safely applied is ________ N (rounded off to the nearest integer).
Band brake: drum rotating clockwise; the band wraps over the top half of the drum; one band end is fixed at the lever pivot, the other is attached to the lever 200 mm from the pivot; braking force F at 1000 mm from the pivotF200 mm800 mm

Answer: 117 N Official key: 115 to 119

  1. The band wraps half the drum: . Band tensions: .
  2. The drum turns clockwise and drags the band towards the right-hand end, so the left end (fixed at the lever pivot) is the tight side: , and .
  3. Moments about the pivot: acts through the pivot (no moment), so , which gives ( N).

Putting the tight side at the 200 mm point gives , outside the key. That arrangement would also over-stress the band before reached the needed value.

Where this shows up in industry

Band brakes still hold winches, hoists and the bands of older automatic gearboxes. The capstan equation is also why a few turns of rope on a bollard can hold a ship.

GATE 2022 · ME Set-1 · Q.39MCQ · 2 marksVibrations

Forced vibration: order the peak-response frequency, the damped and the undamped natural frequency

Consider a forced single degree-of-freedom system governed by where and are the damping ratio and undamped natural frequency of the system, respectively, while is the forcing frequency. The amplitude of the forced steady state response of this system is given by , where . The peak amplitude of this response occurs at a frequency . If denotes the damped natural frequency of this system, which one of the following options is true?
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The amplitude peaks where is smallest. Setting its derivative with respect to to zero gives , so .
  2. The damped natural frequency is .
  3. , so : option (A).

We confirmed it by brute-force search for the peak at , 0.2, 0.4 and 0.6. With light damping all three are close together, which is why "resonance at " is a good approximation in practice.

Where this shows up in industry

When a test engineer reads a natural frequency off a measured frequency-response peak, the peak sits slightly below the true . For lightly damped steel structures () the difference is under 0.3%. For rubber mounts it can matter.

GATE 2022 · ME Set-2 · Q.31NAT · 1 markVibrations

Damping ratio (1/2π) ln 2 and a 4 mm peak in a hammer test. How big is the next positive peak?

For a dynamical system governed by the equation, , the damping ratio is equal to . The displacement of this system is measured during a hammer test. A displacement peak in the positive displacement direction is measured to be 4 mm. Neglecting higher powers () of the damping ratio, the displacement at the next peak in the positive direction will be ________ mm (in integer).

Answer: 2 mm Official key: 1.95 to 2.05

  1. Successive positive peaks fall by the logarithmic decrement: .
  2. Dropping powers of above 1: .
  3. , so .

Keeping the term gives 1.99 mm (), still inside the key.

Where this shows up in industry

This is how damping is measured on real structures: tap the part, record the ring-down with an accelerometer and take the log of the ratio of successive peaks. Modal test software fits the same decay to every mode at once.

GATE 2022 · ME Set-2 · Q.40MCQ · 2 marksVibrations

Match damping and forcing conditions to four response histories (resonance, beats, negative damping)

A spring mass damper system (mass , stiffness , and damping coefficient ) excited by a force , where , and are the amplitude, frequency and time, respectively, is shown in the figure. Four different responses of the system (marked as (i) to (iv)) are shown just to the right of the system figure. In the figures of the responses, is the amplitude of response shown in red color and the dashed lines indicate its envelope. The responses represent only the qualitative trend and those are not drawn to any specific scale.
Four different parameter and forcing conditions are mentioned below.
(P) and   (Q) and   (R) and   (S) and
Which one of the following options gives correct match (indicated by arrow →) of the parameter and forcing conditions to the responses?
Spring-mass-damper excited by F(t) = B sin(omega t), and four response histories: (i) grows and levels off; (ii) grows linearly; (iii) beats, swelling and dying away repeatedly; (iv) grows exponentiallymF(t)kctA(i)tA(ii)tA(iii)tA(iv)
  1. (A)(P) → (i), (Q) → (iii), (R) → (iv), (S) → (ii)
  2. (B)(P) → (ii), (Q) → (iii), (R) → (iv), (S) → (i)
  3. (C)(P) → (i), (Q) → (iv), (R) → (ii), (S) → (iii)
  4. (D)(P) → (iii), (Q) → (iv), (R) → (ii), (S) → (i)

Answer: (C) Official key: C

  1. (P) Damped system forced at resonance: the amplitude grows while the transient builds, then levels off at . That is (i).
  2. (Q) Negative damping feeds energy in at every cycle, so the free part of the motion grows exponentially, whatever the forcing. That is (iv).
  3. (R) Undamped and forced exactly at resonance: the response contains a term , so the envelope rises linearly without limit. That is (ii).
  4. (S) Undamped and forced close to resonance: the forced and free motions drift in and out of phase and the amplitude swells and dies away repeatedly (beats). That is (iii).

So the match is option (C). The four plots on this page are not copies: we computed them by integrating the equation of motion for each condition (), and the script classifies each envelope and checks that the classes give option (C).

Where this shows up in industry

Each trace has a real-world twin. Machines run up through resonance (i); a lightly damped structure driven at its natural frequency keeps building up until something yields (ii); twin-engine aircraft and ships with slightly mismatched shafts beat (iii); and negative damping is how brake squeal, flutter and machining chatter start (iv).

GATE 2024 · ME · Q.25MCQ · 1 markVibrations

Successive amplitudes 7.75 mm and 7.20 mm, 2 kg mass, 15 Hz. What is the damping coefficient?

A linear spring-mass-dashpot system with a mass of 2 kg is set in motion with viscous damping. If the natural frequency is 15 Hz, and the amplitudes of two successive cycles measured are 7.75 mm and 7.20 mm, the coefficient of viscous damping (in N.s/m) is
  1. (A)4.41
  2. (B)7.51
  3. (C)2.52
  4. (D)6.11

Answer: (A) Official key: A

  1. Logarithmic decrement: .
  2. Damping ratio: .
  3. , closest to option (A), 4.41.

Using 15 rad/s instead of 15 Hz gives 0.70, which is no option. Converting Hz to rad/s is the step that most people miss.

Where this shows up in industry

A damping ratio near 1% is typical of a bolted steel structure. Machine mounts, tuned mass dampers and vehicle shock absorbers are specified by this same c (or ζ), which engineers back out from a decay test just like this.

GATE 2024 · ME · Q.55NAT · 2 marksVibrations

A mass on a 2k spring, also pulled through a pulley by a spring k. At what driving frequency does it resonate?

A vibratory system consists of mass , a vertical spring of stiffness and a horizontal spring of stiffness . The end A of the horizontal spring is given a horizontal motion . The other end of the spring is connected to an inextensible rope that passes over two massless pulleys as shown. Assume kg, kN/m, and neglect friction. The magnitude of critical driving frequency for which the oscillations of mass tend to become excessively large is ________ rad/s (answer in integer).
Mass m on a vertical spring 2k; a rope from horizontal spring k, whose end A moves as a sin(omega t), passes over a fixed pulley, down round a pulley attached to the mass, and up to the fixed supportAxA = a sin ωtkm2k

Answer: 30 rad/s Official key: 29 to 31

  1. The lower pulley moves with the mass, and the rope runs down to it and back up, so when the mass moves the rope end at the spring moves .
  2. The horizontal spring then stretches and pulls with on the rope; the rope tension acts twice on the pulley, giving on the mass. Effective stiffness from that branch: (stiffness scales with the square of the lever ratio).
  3. Total: . Large oscillations when .

Treating the springs as simply gives 21.2 rad/s, outside the key: the pulley's 2:1 ratio is the point of the question.

Where this shows up in industry

Any lever, pulley or gear between a spring and a mass scales the stiffness by the ratio squared. Engineers use this to tune machine-tool feed drives, cable-driven robot joints and vehicle suspensions, where the spring sits at a motion ratio of about 0.6-0.9 from the wheel.

GATE 2025 · ME · Q.35NAT · 1 markVibrations

The damping ratio equals ω_d/ω_n. What is the damping ratio?

A block of mass 1 kg connected to a spring of stiffness 10 N m−1 is operating in a viscous medium such that the damping ratio (or damping factor) is equal to the ratio of the damped frequency to the natural frequency. The magnitude of the damping ratio for this system is ________ (rounded off to 2 decimal places).

Answer: 0.71 Official key: 0.70 to 0.72

  1. . The condition is .
  2. Squaring: , so .

The mass and stiffness are not needed: they would only give .

Where this shows up in industry

is a favourite design target. Instrument movements, car suspensions tuned for control, and servo loops all aim near it because it settles fast with only about 4-5% overshoot.

GATE 2025 · ME · Q.42MCQ · 2 marksVibrations

A mass hangs from a cantilever tip that is also held by a spring. What is the natural frequency?

The system shown in the figure below consists of a cantilever beam (with flexural rigidity and negligible mass), a spring (with spring constant and negligible mass) and a block of mass . Assuming a lumped parameter model for the system, the fundamental natural frequency () of the system is
Massless cantilever of length L and flexural rigidity EI fixed at O; its free end hangs from a spring K above and carries a block of mass m belowOKmL
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Tip stiffness of a cantilever under an end load: .
  2. The beam tip and the spring move together with the mass (same ), so their forces add: the springs are in parallel, .
  3. : option (A).

The quick test: same displacement means parallel (stiffnesses add), same force means series (flexibilities add). Here the spring is on the opposite side of the beam from the mass, but it still moves with the tip.

Where this shows up in industry

Lumping a beam into an equivalent spring is the first estimate in every vibration check, before FEA: a bracket carrying a sensor, a machine on a cantilevered frame, a pipe span with a support spring. The equivalent stiffness also tells you which part to stiffen.

GATE 2026 · ME · Q.18MCQ · 1 markVibrations

Critical damping 350 N·s/m, actual 35 N·s/m. What is the logarithmic decrement?

In a single degree of freedom vibrating system with only viscous damping, the critical damping coefficient is 350 N s/m and the damping coefficient is 35 N s/m. The logarithmic decrement of the vibrating system is
  1. (A)0.63
  2. (B)1.26
  3. (C)0.32
  4. (D)1.89

Answer: (A) Official key: A

  1. Damping ratio .
  2. , so 0.63: option (A).

The small-damping form gives 0.628, the same option.

Where this shows up in industry

With each cycle keeps of the last one, so the vibration dies within a few cycles. That is light-vehicle-suspension territory, compared with about 0.06 for a bare steel frame.

From GATE prep to a design and simulation career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.