GATE Mechanical: Machine Design, previous-year questions solved
Every machine design question from the last four GATE Mechanical papers that has an official key and is not already on our strength of materials page: von Mises shear yield, Soderberg vs Goodman vs Gerber, a repeated-load fatigue problem, what improves fatigue strength, an eccentrically loaded rivet pair, transverse and parallel fillet welds, bearing life and selection, and power screw efficiency. Each answer is worked step by step, checked against the official key, and followed by where the idea shows up in a design office.
Questions from official GATE ME papers (IIT Kharagpur 2022, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 10 questions
Tensile yield stress 200 MPa: what is the shear yield stress by the von Mises criterion?
- (A)115.5
- (B)100.0
- (C)66.7
- (D)141.4
Answer: (A) Official key: A
- Von Mises (distortion energy) for plane stress (): yielding starts when .
- Pure shear has principal stresses , , so the left side is , and at yield.
- : option (A).
Trap: the maximum shear stress (Tresca) theory gives , option (B). Tresca is the more conservative of the two; the question asks for von Mises.
The "equivalent (von Mises) stress" plot is the default stress result in FEA tools such as ANSYS and Abaqus, compared directly against the material's yield strength. The same 0.577 factor sets the allowable shear stress for keys, pins and shafts in many design calculations.
Soderberg, modified Goodman, Gerber or yield line: which is the most conservative against fatigue failure?
- (A)Soderberg line
- (B)Modified Goodman line
- (C)Gerber line
- (D)Yield line
Answer: (A) Official key: A
- Each criterion is a line on the mean stress () vs alternating stress () diagram. Designs below the line are safe, so the line that sits lowest allows the least stress: that is the most conservative.
- All three fatigue lines start at the endurance limit on the axis. Soderberg ends at the yield strength : . Goodman ends further out, at the ultimate strength : . Gerber is a parabola through the same end points as Goodman, bulging above it: .
- Example: , , MPa, at MPa the allowed is 125.0 (Soderberg), 166.7 (Goodman), 222.2 (Gerber) and 200 MPa (yield line ). Soderberg is lowest, and since and it stays lowest at every mean stress: option (A).
The yield (Langer) line only guards against yielding on the first cycle; it starts at , above , so it is not a fatigue criterion at all.
Soderberg is rarely used for new designs because it is so conservative; most machine design texts and calculation tools default to modified Goodman, and Gerber (or an ASME elliptic curve) is used to fit test data. Soderberg survives in older shaft design formulas and anywhere a part must never yield, even locally.
Endurance limit = yield strength, load applied and removed, Soderberg with factor of safety 2: what is the maximum stress?
- (A)one-fourth of the endurance limit
- (B)half of the endurance limit
- (C)the endurance limit
- (D)twice the endurance limit
Answer: (B) Official key: B
- \"Loaded in tension and unloaded\" is a repeated (pulsating) stress from 0 to : .
- Soderberg with factor of safety : . With and : .
- So : half of the endurance limit, option (B). The ultimate strength is not needed: Soderberg uses , not .
Traps: leaving out the factor of safety gives (option C). Using Goodman (with ) instead of Soderberg would give , which is not among the options, a hint that the ultimate strength is a distractor here.
Parts that are loaded and unloaded rather than reversed are everywhere: bolts in a flange that is pressurised every cycle, crane hooks, connecting rod bolts and valve springs. Treating them with instead of as fully reversed is a standard step in fatigue calculations and in FEA fatigue post-processors.
Surface finish, shot peening, humidity: which of these improve the fatigue strength of a mild steel shaft?
- (A)Enhancing surface finish
- (B)Shot peening of the shaft
- (C)Increasing relative humidity
- (D)Reducing relative humidity
Answer: (A, B, D), or (A, B) Official key: A,B,D OR A, B
- Fatigue cracks almost always start at the surface. A smoother finish removes the tiny notches (machining marks) where cracks start, so the surface finish factor rises: (A) improves fatigue strength.
- Shot peening blasts the surface with small hard shot, leaving a thin layer in compressive residual stress. A crack needs tension to open and grow, so the compressive layer delays it: (B) improves fatigue strength.
- Moisture makes mild steel corrode, and corrosion pits act as notches (corrosion fatigue), so higher humidity lowers fatigue strength: (C) is wrong. Reducing humidity therefore helps, which is why the official key accepts (A, B, D); it also accepts (A, B), since humidity is not usually counted among design methods.
Shot peening is standard on coil and leaf springs, gears, crankshafts and landing gear, with the peening intensity checked on Almen strips. Shafts with keyways and shoulders get a fine-turned or ground finish at the stress raisers, and exposed steel parts are painted, plated or oiled because corrosion can wipe out the endurance limit altogether.
Two rivets 100 mm apart, P = 10 kN at e = 3√7a, permissible shear 50 MPa: what is the minimum rivet area?
- (A)800
- (B)25
- (C)
- (D)200
Answer: (A) Official key: A
- Move to the centroid of the rivet group (midway between U and V): a direct load plus a moment .
- Direct (primary) shear, shared equally and acting downward: on each rivet.
- Secondary shear from the moment, proportional to the distance from the centroid: .
- The rivets lie on a vertical line, so (perpendicular to the radius) is horizontal while is vertical: they add at right angles, on each rivet.
- : option (A).
Traps: designing for the direct load alone (, option D) ignores the moment, which is what the 2a and e are there for. Adding the two forces arithmetically ( kN, ) is wrong too: they are perpendicular here.
The same direct-plus-secondary method sizes bolt groups on eccentrically loaded brackets, crane rail brackets and steel structure connections (IS 800 for bolted joints). Aircraft skins are still riveted, and the rivet farthest from the group centroid is always the one checked first.
10 mm plates, one transverse fillet weld, 5 kN, weld UTS 150 MPa, factor of safety 3: what weld length is needed?
Answer: 14.14 mm Official key: 12.00 to 14.20 OR 18.00 to 28.40 OR 32.00 to 34.20
- The weld leg equals the plate thickness, mm. A 45° fillet weld fails across its throat: mm.
- Allowable stress: . Machine design texts check a transverse fillet weld in tension on the throat area: .
- , inside the official range 12.00 to 14.20.
The official key also accepts two other ranges, 18.00 to 28.40 and 32.00 to 34.20, because conventions differ. Structural codes treat every fillet weld as failing in shear on the throat: taking the shear allowable as half the tensile ( MPa) gives mm, inside the second range. Trap: using the leg (10 mm) instead of the throat gives mm, outside every range.
Drawings call out fillet welds by leg size, but codes (AWS D1.1, IS 816 / IS 800 in India) size them on the effective throat. Welding engineers also add the start and stop craters to the specified length, since the ends of a run are not full size.
Plate welded to a gusset with two parallel fillet welds of length l and leg h: what is the critical load?
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- A parallel (side) fillet weld carries the load in shear along its length, across the throat .
- One weld: .
- The figure has two welds, one along each edge of the plate: : option (A).
Trap: option (C) is the strength of one weld; it is the right answer only if you miss the second weld in the figure.
Gusset plates in steel trusses, towers and crane booms are joined exactly like this, with a weld on each side of the member so the load passes through the plate without twisting it. When the member is an angle section, the two weld lengths are made unequal so their combined resistance lines up with the angle's centroid.
Ball bearing life L = (C/P)^n: what is n, and which race is assumed to rotate?
- (A), assuming that the inner racing is fixed and outer racing is revolving
- (B), assuming that the inner racing is fixed and outer racing is revolving
- (C), assuming that the outer racing is fixed and inner racing is revolving
- (D), assuming that the outer racing is fixed and inner racing is revolving
Answer: (C) Official key: C
- The basic rating life is million revolutions, with for ball bearings and for roller bearings. is the load at which 90% of a large group of identical bearings survive one million revolutions. So , ruling out (B) and (D): with , doubling the load would raise the life.
- Load ratings are defined for the usual case: inner ring rotating with the shaft, outer ring fixed in the housing. That is why the older equivalent-load formula uses a rotation factor for a rotating inner ring and a higher (1.2) when the outer ring rotates: option (C).
A useful consequence of : doubling the load cuts the life to one eighth.
Bearing selection in every manufacturer catalogue starts from this ISO 281 life equation, usually converted to hours: . Wheel hubs, where the outer ring rotates with the wheel, are the classic case where the rotating-race assumption matters.
A shaft carries a helical gear: which bearing can NOT support it?
- (A)Angular contact bearing
- (B)Double-row ball bearing
- (C)Straight roller bearing
- (D)Tapered roller bearing
Answer: (C) Official key: C
- Helical teeth meet at the helix angle, so the tooth force has an axial (thrust) component along the shaft as well as radial and tangential components: .
- The bearings must therefore take combined radial and axial load. Angular contact ball bearings and tapered roller bearings are built for exactly that, and double-row ball bearings carry axial load in both directions.
- A straight (cylindrical) roller bearing has rollers parallel to the shaft and, in its common forms, no ribs on one ring, so the rings slide axially relative to each other: it carries radial load only. Option (C).
Some cylindrical roller designs with ribs on both rings (NJ, NUP types) take a light axial load, but in the sense of the question (and the key) the straight roller bearing is the one that cannot locate a helical gear shaft.
Automotive gearboxes and axles with helical and hypoid gears run on tapered roller bearings for this reason. Where a cylindrical roller bearing is used, it is placed as the non-locating (floating) bearing at one end so the shaft can grow with heat, while a ball or tapered bearing at the other end takes the thrust.
Square-threaded screw lifting load W with effort F: how is its efficiency defined?
- (A)The ratio of work done by W per revolution to work done by F per revolution
- (B)
- (C)
- (D)The ratio of work done by F per revolution to work done by W per revolution
Answer: (A) Official key: A
- Efficiency is useful work out over work in. In one revolution the load rises by the lead (work , done on the load) and the effort moves around the mean circle (work at the mean diameter).
- , the ratio of the load's work to the effort's work per revolution: option (A). Option (D) is the inverse, always greater than 1 for a real screw.
- (option B) is the mechanical advantage, not the efficiency; it ignores how far each force moves.
With this becomes . For a 50 mm mean diameter, 10 mm lead () and : . A self-locking screw () always has .
Screw jacks, vices and the lead screws on older machine tools use square or trapezoidal (ACME) threads and are self-locking, so the load stays put when you let go, at the price of low efficiency. CNC machines use recirculating ball screws instead, which roll rather than slide and reach about 90% efficiency, but they need a brake because they are not self-locking.