GATE Mechanical: Theory of Machines and Vibrations, previous-year questions solved, part 2

Part 2 of 2 of the Theory of Machines and Vibrations hub: 15 more official GATE ME questions on flywheels, governors, balancing, gyroscope and brakes and vibrations, each solved step by step and checked against the official answer key. Part 1 covers mechanisms and velocity analysis and gears and gear trains.

Questions from official GATE ME papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 15 of 29 questions on this page

GATE 2024 · ME · Q.23MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

An engine's energy fluctuation is 300 J and it runs between 220 and 280 rad/s. What flywheel inertia gives a 0.05 fluctuation coefficient?

The change in kinetic energy of an engine is 300 J, and minimum and maximum shaft speeds are rad/s and rad/s, respectively. Assume that the torque-time function is purely harmonic. To achieve a coefficient of fluctuation of 0.05, the moment of inertia (in kg.m2) of the flywheel to be mounted on the engine shaft is
  1. (A)0.113
  2. (B)0.096
  3. (C)0.071
  4. (D)0.053

Answer: (B) Official key: B

  1. The mean speed is .
  2. Energy fluctuation and speed fluctuation: .
  3. : option (B).

The 220-280 rad/s band only fixes the mean speed. Using it as the fluctuation itself () gives 0.020, which is no option. The 0.05 coefficient is the target the flywheel has to achieve.

Where this shows up in industry

Single-cylinder engines, punch presses and reciprocating compressors all need a flywheel to ride through an uneven torque. Dual-mass flywheels in diesel cars split the inertia across a spring to keep crankshaft fluctuations out of the gearbox.

GATE 2022 · ME Set-1 · Q.17MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

A Watt governor runs at h = 400 mm. What is h if the speed doubles?

The figure shows a schematic of a simple Watt governor mechanism with the spindle rotating at an angular velocity about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot is denoted by . The value of mm at a certain . If is doubled, the value of will be ________ mm.
Watt governor: spindle O1O2 rotating at omega about a vertical axis; arms of length l1 from pivot O1 to balls P and S, links l2 to the sleeve QR; h is the height of O1 above the plane of the ballsO₁ωPSQRSleeve (QR), O₂l₁l₁l₂l₂hg = 9.8 m/s²
  1. (A)50
  2. (B)100
  3. (C)150
  4. (D)200

Answer: (B) Official key: B

  1. With massless links and sleeve, only the balls matter. Take moments about for one ball at radius and height below it: .
  2. So . The arm length and ball mass drop out.
  3. : doubling divides by 4, so . Option (B).

At mm the speed is , about 47 rpm. That is why simple Watt governors only work at low speeds: at higher speeds becomes tiny and the governor loses sensitivity.

Where this shows up in industry

Watt governors controlled steam engines. The same balance of centrifugal force and gravity (or a spring) still works in mechanical diesel injection-pump governors, centrifugal clutches and overspeed trips on turbines.

GATE 2022 · ME Set-2 · Q.39MCQ · 2 marksFlywheels, governors, balancing, gyroscope and brakes

Two 1 kg masses at 1 cm and 90° apart: at what radius does a √2 kg mass balance them?

A rigid body in the X-Y plane consists of two point masses (1 kg each) attached to the ends of two massless rods, each of 1 cm length, as shown in the figure. It rotates at 30 RPM counter-clockwise about the Z-axis passing through point O. A point mass of kg, attached to one end of a third massless rod, is used for balancing the body by attaching the free end of the rod to point O. The length of the third rod is ________ cm.
Two 1 kg point masses on massless rods 1 cm long, 90 degrees apart, rotating at 30 RPM counter-clockwise about point O in the X-Y planeXY1 kg1 kg1 cm1 cm90°30 RPMO
  1. (A)1
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Balance means the vector sum of is zero (the speed, 30 RPM, does not matter).
  2. The two masses give 1 kg·cm each at 90° apart, a resultant of .
  3. The balancing mass must supply kg·cm in the opposite direction: , so . Option (A).
Where this shows up in industry

Every tyre change ends on a wheel balancer, which finds the imbalance and asks for a clip-on weight at the right angle. Fans, rotors and crankshafts are balanced the same way, usually in two planes as in the next question.

GATE 2025 · ME · Q.29MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

Balancing: which is true for a rigid rotor and for a single-cylinder engine?

In the context of balancing of rotating and reciprocating masses, which one of the following options is true?
  1. (A)An unbalanced rigid rotor can be completely balanced using a single balancing mass
  2. (B)An unbalanced rigid rotor can be completely balanced using two balancing masses attached in two distinct planes
  3. (C)A single-cylinder internal combustion engine can be completely balanced using a single balancing mass
  4. (D)A single-cylinder internal combustion engine can be completely balanced using two balancing masses

Answer: (B) Official key: B

  1. A rigid rotor with masses spread along its length has an unbalanced force and an unbalanced couple. One mass can cancel the force but not the couple. Two masses in two planes can cancel both: (B) is true, and (A) is false.
  2. A single-cylinder engine's reciprocating mass gives a shaking force along the line of stroke that varies as (primary) and (secondary). Rotating counterweights on the crank produce a force of constant size that turns with it. They can only move part of the primary force to the perpendicular direction, never cancel it completely. So (C) and (D) are false.
Where this shows up in industry

Two-plane balancing is the standard production test for crankshafts, motor rotors and turbine spools. Single-cylinder motorcycles and lawn-mower engines carry a counterweight of about 50% of the reciprocating mass and accept some vibration. Many add a geared balance shaft.

GATE 2026 · ME · Q.20MCQ · 1 markFlywheels, governors, balancing, gyroscope and brakes

An aircraft engine rotor (1 kg·m², 500 rpm) turns on a 2 km radius at 1200 km/h. What is the gyroscopic moment?

The rotor of an aeroplane engine has a mass moment of inertia 1.0 kg m2. The engine rotates at a speed of 500 RPM in the clockwise direction if viewed from the front of the aeroplane. If the aeroplane while flying at 1200 km/hr turns with a radius of 2 km at same elevation, then the magnitude of the gyroscopic moment exerted by the rotor on the aeroplane structure in N m is
  1. (A)8.73
  2. (B)17.46
  3. (C)4.37
  4. (D)26.19

Answer: (A) Official key: A

  1. Spin: .
  2. Precession (the turn rate): .
  3. Gyroscopic couple: . Option (A).

The direction (nose up or down) depends on the turn direction and the spin sense. The question asks only for the magnitude.

Where this shows up in industry

The same couple loads ship turbines when the hull pitches, motorcycle wheels when a rider leans into a turn, and the bearings of wind-turbine rotors when the nacelle yaws. Designers size those bearings for it.

GATE 2024 · ME · Q.59NAT · 2 marksFlywheels, governors, balancing, gyroscope and brakes

A band brake, μ = 0.3, band limit 1.5 kN. What is the largest lever force F?

A band brake shown in the figure has a coefficient of friction of 0.3. The band can take a maximum force of 1.5 kN. The maximum braking force () that can be safely applied is ________ N (rounded off to the nearest integer).
Band brake: drum rotating clockwise; the band wraps over the top half of the drum; one band end is fixed at the lever pivot, the other is attached to the lever 200 mm from the pivot; braking force F at 1000 mm from the pivotF200 mm800 mm

Answer: 117 N Official key: 115 to 119

  1. The band wraps half the drum: . Band tensions: .
  2. The drum turns clockwise and drags the band towards the right-hand end, so the left end (fixed at the lever pivot) is the tight side: , and .
  3. Moments about the pivot: acts through the pivot (no moment), so , which gives ( N).

Putting the tight side at the 200 mm point gives , outside the key. That arrangement would also over-stress the band before reached the needed value.

Where this shows up in industry

Band brakes still hold winches, hoists and the bands of older automatic gearboxes. The capstan equation is also why a few turns of rope on a bollard can hold a ship.

GATE 2022 · ME Set-1 · Q.39MCQ · 2 marksVibrations

Forced vibration: order the peak-response frequency, the damped and the undamped natural frequency

Consider a forced single degree-of-freedom system governed by where and are the damping ratio and undamped natural frequency of the system, respectively, while is the forcing frequency. The amplitude of the forced steady state response of this system is given by , where . The peak amplitude of this response occurs at a frequency . If denotes the damped natural frequency of this system, which one of the following options is true?
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The amplitude peaks where is smallest. Setting its derivative with respect to to zero gives , so .
  2. The damped natural frequency is .
  3. , so : option (A).

We confirmed it by brute-force search for the peak at , 0.2, 0.4 and 0.6. With light damping all three are close together, which is why "resonance at " is a good approximation in practice.

Where this shows up in industry

When a test engineer reads a natural frequency off a measured frequency-response peak, the peak sits slightly below the true . For lightly damped steel structures () the difference is under 0.3%. For rubber mounts it can matter.

GATE 2022 · ME Set-2 · Q.31NAT · 1 markVibrations

Damping ratio (1/2π) ln 2 and a 4 mm peak in a hammer test. How big is the next positive peak?

For a dynamical system governed by the equation, , the damping ratio is equal to . The displacement of this system is measured during a hammer test. A displacement peak in the positive displacement direction is measured to be 4 mm. Neglecting higher powers () of the damping ratio, the displacement at the next peak in the positive direction will be ________ mm (in integer).

Answer: 2 mm Official key: 1.95 to 2.05

  1. Successive positive peaks fall by the logarithmic decrement: .
  2. Dropping powers of above 1: .
  3. , so .

Keeping the term gives 1.99 mm (), still inside the key.

Where this shows up in industry

This is how damping is measured on real structures: tap the part, record the ring-down with an accelerometer and take the log of the ratio of successive peaks. Modal test software fits the same decay to every mode at once.

GATE 2022 · ME Set-2 · Q.40MCQ · 2 marksVibrations

Match damping and forcing conditions to four response histories (resonance, beats, negative damping)

A spring mass damper system (mass , stiffness , and damping coefficient ) excited by a force , where , and are the amplitude, frequency and time, respectively, is shown in the figure. Four different responses of the system (marked as (i) to (iv)) are shown just to the right of the system figure. In the figures of the responses, is the amplitude of response shown in red color and the dashed lines indicate its envelope. The responses represent only the qualitative trend and those are not drawn to any specific scale.
Four different parameter and forcing conditions are mentioned below.
(P) and   (Q) and   (R) and   (S) and
Which one of the following options gives correct match (indicated by arrow →) of the parameter and forcing conditions to the responses?
Spring-mass-damper excited by F(t) = B sin(omega t), and four response histories: (i) grows and levels off; (ii) grows linearly; (iii) beats, swelling and dying away repeatedly; (iv) grows exponentiallymF(t)kctA(i)tA(ii)tA(iii)tA(iv)
  1. (A)(P) → (i), (Q) → (iii), (R) → (iv), (S) → (ii)
  2. (B)(P) → (ii), (Q) → (iii), (R) → (iv), (S) → (i)
  3. (C)(P) → (i), (Q) → (iv), (R) → (ii), (S) → (iii)
  4. (D)(P) → (iii), (Q) → (iv), (R) → (ii), (S) → (i)

Answer: (C) Official key: C

  1. (P) Damped system forced at resonance: the amplitude grows while the transient builds, then levels off at . That is (i).
  2. (Q) Negative damping feeds energy in at every cycle, so the free part of the motion grows exponentially, whatever the forcing. That is (iv).
  3. (R) Undamped and forced exactly at resonance: the response contains a term , so the envelope rises linearly without limit. That is (ii).
  4. (S) Undamped and forced close to resonance: the forced and free motions drift in and out of phase and the amplitude swells and dies away repeatedly (beats). That is (iii).

So the match is option (C). The four plots on this page are not copies: we computed them by integrating the equation of motion for each condition (), and the script classifies each envelope and checks that the classes give option (C).

Where this shows up in industry

Each trace has a real-world twin. Machines run up through resonance (i); a lightly damped structure driven at its natural frequency keeps building up until something yields (ii); twin-engine aircraft and ships with slightly mismatched shafts beat (iii); and negative damping is how brake squeal, flutter and machining chatter start (iv).

GATE 2023 · ME · Q.30NAT · 1 markVibrations

A 20 kg block on two 1000 N/m springs: how long do ten free oscillations take?

The figure shows a block of mass kg attached to a pair of identical linear springs, each having a spring constant N/m. The block oscillates on a frictionless horizontal surface. Assuming free vibrations, the time taken by the block to complete ten oscillations is _________ seconds. (Rounded off to two decimal places)
Take .
Block of mass m on a frictionless floor, joined to a fixed wall on its left by two identical springs k, one above the other, both running from the wall to the block; a double arrow shows the block moves left and rightkkm

Answer: 6.28 s Official key: 6.27 to 6.29

  1. Both springs run from the wall to the block, so both stretch by the block's displacement: they act in parallel, .
  2. .
  3. Period: .
  4. Ten oscillations: .

Traps: treating the springs as in series () gives 12.56 s, and using one spring gives 8.88 s; both are outside the key. Same displacement means parallel; same force means series.

Where this shows up in industry

Machine mounts, vehicle suspensions with more than one spring per corner, and isolator pads under equipment all add stiffness this way. Isolator selection starts from the same number: the natural frequency of the mounted mass on the combined stiffness, which must sit well below the forcing frequency.

GATE 2024 · ME · Q.25MCQ · 1 markVibrations

Successive amplitudes 7.75 mm and 7.20 mm, 2 kg mass, 15 Hz. What is the damping coefficient?

A linear spring-mass-dashpot system with a mass of 2 kg is set in motion with viscous damping. If the natural frequency is 15 Hz, and the amplitudes of two successive cycles measured are 7.75 mm and 7.20 mm, the coefficient of viscous damping (in N.s/m) is
  1. (A)4.41
  2. (B)7.51
  3. (C)2.52
  4. (D)6.11

Answer: (A) Official key: A

  1. Logarithmic decrement: .
  2. Damping ratio: .
  3. , closest to option (A), 4.41.

Using 15 rad/s instead of 15 Hz gives 0.70, which is no option. Converting Hz to rad/s is the step that most people miss.

Where this shows up in industry

A damping ratio near 1% is typical of a bolted steel structure. Machine mounts, tuned mass dampers and vehicle shock absorbers are specified by this same c (or ζ), which engineers back out from a decay test just like this.

GATE 2024 · ME · Q.55NAT · 2 marksVibrations

A mass on a 2k spring, also pulled through a pulley by a spring k. At what driving frequency does it resonate?

A vibratory system consists of mass , a vertical spring of stiffness and a horizontal spring of stiffness . The end A of the horizontal spring is given a horizontal motion . The other end of the spring is connected to an inextensible rope that passes over two massless pulleys as shown. Assume kg, kN/m, and neglect friction. The magnitude of critical driving frequency for which the oscillations of mass tend to become excessively large is ________ rad/s (answer in integer).
Mass m on a vertical spring 2k; a rope from horizontal spring k, whose end A moves as a sin(omega t), passes over a fixed pulley, down round a pulley attached to the mass, and up to the fixed supportAxA = a sin ωtkm2k

Answer: 30 rad/s Official key: 29 to 31

  1. The lower pulley moves with the mass, and the rope runs down to it and back up, so when the mass moves the rope end at the spring moves .
  2. The horizontal spring then stretches and pulls with on the rope; the rope tension acts twice on the pulley, giving on the mass. Effective stiffness from that branch: (stiffness scales with the square of the lever ratio).
  3. Total: . Large oscillations when .

Treating the springs as simply gives 21.2 rad/s, outside the key: the pulley's 2:1 ratio is the point of the question.

Where this shows up in industry

Any lever, pulley or gear between a spring and a mass scales the stiffness by the ratio squared. Engineers use this to tune machine-tool feed drives, cable-driven robot joints and vehicle suspensions, where the spring sits at a motion ratio of about 0.6-0.9 from the wheel.

GATE 2025 · ME · Q.35NAT · 1 markVibrations

The damping ratio equals ω_d/ω_n. What is the damping ratio?

A block of mass 1 kg connected to a spring of stiffness 10 N m−1 is operating in a viscous medium such that the damping ratio (or damping factor) is equal to the ratio of the damped frequency to the natural frequency. The magnitude of the damping ratio for this system is ________ (rounded off to 2 decimal places).

Answer: 0.71 Official key: 0.70 to 0.72

  1. . The condition is .
  2. Squaring: , so .

The mass and stiffness are not needed: they would only give .

Where this shows up in industry

is a favourite design target. Instrument movements, car suspensions tuned for control, and servo loops all aim near it because it settles fast with only about 4-5% overshoot.

GATE 2025 · ME · Q.42MCQ · 2 marksVibrations

A mass hangs from a cantilever tip that is also held by a spring. What is the natural frequency?

The system shown in the figure below consists of a cantilever beam (with flexural rigidity and negligible mass), a spring (with spring constant and negligible mass) and a block of mass . Assuming a lumped parameter model for the system, the fundamental natural frequency () of the system is
Massless cantilever of length L and flexural rigidity EI fixed at O; its free end hangs from a spring K above and carries a block of mass m belowOKmL
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Tip stiffness of a cantilever under an end load: .
  2. The beam tip and the spring move together with the mass (same ), so their forces add: the springs are in parallel, .
  3. : option (A).

The quick test: same displacement means parallel (stiffnesses add), same force means series (flexibilities add). Here the spring is on the opposite side of the beam from the mass, but it still moves with the tip.

Where this shows up in industry

Lumping a beam into an equivalent spring is the first estimate in every vibration check, before FEA: a bracket carrying a sensor, a machine on a cantilevered frame, a pipe span with a support spring. The equivalent stiffness also tells you which part to stiffen.

GATE 2026 · ME · Q.18MCQ · 1 markVibrations

Critical damping 350 N·s/m, actual 35 N·s/m. What is the logarithmic decrement?

In a single degree of freedom vibrating system with only viscous damping, the critical damping coefficient is 350 N s/m and the damping coefficient is 35 N s/m. The logarithmic decrement of the vibrating system is
  1. (A)0.63
  2. (B)1.26
  3. (C)0.32
  4. (D)1.89

Answer: (A) Official key: A

  1. Damping ratio .
  2. , so 0.63: option (A).

The small-damping form gives 0.628, the same option.

Where this shows up in industry

With each cycle keeps of the last one, so the vibration dies within a few cycles. That is light-vehicle-suspension territory, compared with about 0.06 for a bare steel frame.

From GATE prep to a design and simulation career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.