GATE Mechanical: Calculus and Vector Calculus (Engineering Mathematics), previous-year questions solved, part 2

Part 2 of 2 of the Calculus and Vector Calculus hub: 10 more official GATE ME questions on Fourier series and vector calculus: gradient, divergence, curl and flux, each solved step by step and checked against the official answer key. Part 1 covers limits, maxima and minima, Taylor series and definite and double integrals.

Questions from official GATE ME papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 10 of 19 questions on this page

GATE 2022 · ME Set-1 · Q.14MCQ · 1 markFourier series

Fourier series of x³ on −1 ≤ x < 1: sine terms, cosine terms or both?

The Fourier series expansion of in the interval with periodic continuation has
  1. (A)only sine terms
  2. (B)only cosine terms
  3. (C)both sine and cosine terms
  4. (D)only sine terms and a non-zero constant

Answer: (A) Official key: A

  1. is odd: . On the symmetric interval , its product with an even function is odd and integrates to zero, so every , including the constant , is zero.
  2. The product with is even, so the survive: , with .
  3. Only sine terms: option (A).

Trap (D): a non-zero constant would mean a non-zero average over one period, but an odd function's average over is zero. Numerically, to all came out below and to matched the formula above.

Where this shows up in industry

Fourier series are how vibration engineers read signals. An FFT of an accelerometer trace splits engine, gearbox or bearing vibration into harmonics, and symmetry shows up directly: a waveform with odd symmetry has only sine content, one with half-wave symmetry only odd harmonics. Order analysis in NVH testing and harmonic analysis in ANSYS both rest on this decomposition.

GATE 2022 · ME Set-2 · Q.11MCQ · 1 markFourier series

Square wave between 4 and 0, 1 s at each level: what is the constant Fourier term?

is a periodic square wave function as shown. It takes only two values, 4 and 0, and stays at each of these values for 1 second before changing. What is the constant term in the Fourier series expansion of ?
Periodic square wave F(t): 4 from t = 0 to 1 s, 0 from 1 to 2 s, repeating every 2 s; the plot runs from t = -3 to 4 sF(t)t (s)−3−2−1123404
  1. (A)1
  2. (B)2
  3. (C)3
  4. (D)4

Answer: (B) Official key: B

  1. The constant term of a Fourier series is the average value of the function over one period.
  2. Period s: for 1 s and for 1 s. Average : option (B).

Trap (D): with the series written as , the coefficient is , and the constant term is . Typing itself gives 4. Averaging the wave numerically over a period gives 2.

Where this shows up in industry

The constant (DC) term is the mean of a periodic signal: the average torque of an engine over a cycle, the mean voltage of a PWM motor drive (duty cycle times supply voltage, here 50% of 4), the mean stress in a fatigue load cycle. Fatigue checks use exactly this split: mean stress (the DC term) plus alternating stress (the harmonics).

GATE 2022 · ME Set-1 · Q.48NAT · 2 marksVector calculus: gradient, divergence, curl and flux

Component of a = 5i + 7j + 2k orthogonal to b = 3i − j + 6k, in their plane: what is its magnitude?

Consider two vectors: Magnitude of the component of orthogonal to in the plane containing the vectors and is __________ (round off to 2 decimal places).

Answer: 8.32 Official key: 7.90 to 8.70

  1. Split into a part along and a part perpendicular to it. Both parts lie in the plane of and .
  2. , , .
  3. Parallel part: .
  4. Perpendicular part, by Pythagoras: , which rounds to 8.32.

Same answer another way: , since the cross product's magnitude is . Trap: the parallel part 2.95 is the projection, the opposite of what is asked.

Where this shows up in industry

Splitting a vector into components along and across a direction is everyday mechanics: normal and tangential force on an inclined contact (friction uses the normal part), axial and shear load on a bolt, and the normal and shear stress on a weld throat or a fibre direction in a composite. FEA post-processors do this projection when you ask for stress in a local coordinate system.

GATE 2022 · ME Set-1 · Q.13MCQ · 1 markVector calculus: gradient, divergence, curl and flux

Flux of ∇φ, φ = (x² + y² + z²)/2, out of a unit sphere

Given a function in three-dimensional Cartesian space, the value of the surface integral where is the surface of a sphere of unit radius and is the outward unit normal vector on , is
  1. (A)
  2. (B)
  3. (C)
  4. (D)0

Answer: (A) Official key: A

  1. , the position vector.
  2. Direct route: on the unit sphere (radius 1), so everywhere. The integral is the surface area, .
  3. Divergence theorem route: , times the volume gives : option (A).

Trap (C): is the sphere's volume, what you get if you forget the divergence is 3, not 1. A direct numerical surface integral over the sphere gives 12.566460 ().

Where this shows up in industry

The divergence theorem is the foundation of the finite volume method used by ANSYS Fluent, OpenFOAM and STAR-CCM+: the change of mass, momentum or energy inside each cell is computed from the fluxes through its faces. It is also Gauss's law for heat: the total heat leaving a closed surface equals the heat generated inside it.

GATE 2024 · ME · Q.12MCQ · 1 markVector calculus: gradient, divergence, curl and flux

Closed surface integral of z dx dy over a sphere of radius R

The value of the surface integral where is the external surface of the sphere is
  1. (A)0
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. In surface-integral notation, means the flux of the field : is the projection of the surface element.
  2. Divergence theorem: , so the integral equals the enclosed volume, : option (C).

Trap (A): the integrand is odd, which tempts you to answer 0. But is odd too (negative on the lower half, where is negative), so is positive everywhere and nothing cancels. A numerical surface integral of for gives 4.18899 against .

Where this shows up in industry

Flux integrals like this give a body's volume, buoyancy and pressure force from its surface alone: integrating pressure times the normal over a hull's wetted surface gives Archimedes' buoyancy. CAD systems compute volume, mass and centroid of a solid model the same way, by integrating over its boundary surfaces.

GATE 2022 · ME Set-2 · Q.12MCQ · 1 markVector calculus: gradient, divergence, curl and flux

Flux of F = 3x i + 5y j + 6z k out of a unit cube centred at (1, 2, 3)

Consider a cube of unit edge length and sides parallel to co-ordinate axes, with its centroid at the point (1, 2, 3). The surface integral of a vector field over the entire surface of the cube is ______.
  1. (A)14
  2. (B)27
  3. (C)28
  4. (D)31

Answer: (A) Official key: A

  1. Divergence theorem: , a constant.
  2. Flux : option (A).

The centroid is a distraction: with a constant divergence, only the volume matters. Face by face it is just as quick: the two faces are 1 apart, so their net flux is ; likewise and for and . Trap (D): plugging the centroid into gives , and adding the components gives 31. A face-by-face numerical integral gives 14 with the cube at and 14 at the origin.

Where this shows up in industry

This is a finite volume cell in miniature. A CFD solver checks that, for every cell, the net flux through its faces balances what is created or stored inside; a constant divergence means a uniform source, like uniform heat generation in a battery cell or a resistive conductor. Mass imbalance across cells is one of the residuals you watch converge in Fluent or OpenFOAM.

GATE 2023 · ME · Q.31NAT · 1 markVector calculus: gradient, divergence, curl and flux

Flux of B = x i + y j − 2z k through the curved surface of a cone (h = 2, r = 3)

A vector field is defined over a conical region having height , base radius and axis along , as shown in the figure. The base of the cone lies in the x-y plane and is centered at the origin.
If denotes the unit outward normal to the curved surface of the cone, the value of the integral equals _________ . (Answer in integer)
Cone with its base of radius r in the x-y plane centred at the origin O and its axis along z; height h; S marks the curved surfacezyxrOhS

Answer: 0 Official key: -0.001 to 0.001

  1. Close the surface with the flat base and use the divergence theorem: , so the net flux out of the whole closed cone (curved surface plus base) is zero.
  2. Base: it lies in with outward normal , so everywhere on it. The base carries no flux.
  3. So the curved surface carries none either: .

It is zero by cancellation, not because nothing flows. The horizontal part pushes out through the curved surface (), and the vertical part pulls exactly back in. A direct numerical integral over the curved surface gives and for the two parts, which add to less than : zero to rounding.

Where this shows up in industry

A divergence-free field like this one is what an incompressible flow looks like: whatever enters a region through one face must leave through another. CFD solvers for water, oil and low-speed air enforce exactly this on every cell (the continuity equation), and a non-zero net flux through a closed control volume is the mass-imbalance residual you watch converge.

GATE 2025 · ME · Q.13MCQ · 1 markVector calculus: gradient, divergence, curl and flux

What is the divergence of the curl of a vector field?

The divergence of the curl of a vector field is
  1. (A)the magnitude of this vector field
  2. (B)the argument of this vector field
  3. (C)the magnitude of the curl of this vector field
  4. (D)zero

Answer: (D) Official key: D

  1. Write in components and take its divergence:
  2. The six mixed second derivatives cancel in pairs ( against , and so on) for any field with continuous second derivatives. The result is identically zero: option (D).

Companion identity worth memorising: , the curl of a gradient is zero. We checked the first one numerically on the field at three points: the curl itself is far from zero, its divergence is zero to rounding error.

Where this shows up in industry

Because , a magnetic field written as the curl of a vector potential automatically has no divergence, which is how electromagnetic FEA (motor and transformer design in tools like Ansys Maxwell) guarantees physical fields. In fluids, the vorticity (the curl of velocity) is divergence-free for the same reason, a fact used in vortex methods and in checking CFD results.

GATE 2025 · ME · Q.46NAT · 2 marksVector calculus: gradient, divergence, curl and flux

Directional derivative of f = x² + xy² at (1, 0) along (i + √3 j)/2

The directional derivative of the function given below at the point in the direction of is ____________ (rounded off to 1 decimal place).

Answer: 1.0 Official key: 0.9 to 1.1

  1. Gradient: . At : .
  2. The direction already has length , so no normalising is needed.
  3. , so the answer is 1.0.

Trap: is the largest rate of change, along the gradient itself, not along the given direction (60° away from it, and ). A finite-difference step along gives 1.000000.

Where this shows up in industry

Directional derivatives tell you how fast temperature, stress or pressure changes along a particular line: the temperature gradient through a weld along the plate, the stress gradient at a notch used in fatigue (notch sensitivity), or a sensitivity in design optimisation, where the solver needs the change in mass or stress along a proposed design change.

GATE 2026 · ME · Q.12MCQ · 1 markVector calculus: gradient, divergence, curl and flux

Is the gradient ∇φ perpendicular or parallel to a surface of constant φ?

Let be a scalar function. Then, is
  1. (A)always perpendicular to the surface of constant
  2. (B)always parallel to the surface of constant
  3. (C)the minimum rate of change of scalar
  4. (D)always zero

Answer: (A) Official key: A

  1. Move a small step within a surface of constant . Then doesn't change: .
  2. So is perpendicular to every direction lying in the surface: it is normal to the surface of constant , option (A).
  3. (C) is backwards: is the maximum rate of change, reached along . (D) holds only at stationary points.

We checked it on the ellipsoid : at 200 random points, the gradient's dot product with both surface tangent vectors was zero to of their lengths.

Where this shows up in industry

Heat flows along , perpendicular to isotherms, which is why heat-flux arrows in a thermal FEA plot cross the temperature contours at right angles. CAD uses the same fact to get the normal of an implicit surface, and contact algorithms in crash and forming simulation use surface normals from gradients to push penetrating nodes back out.

From GATE prep to a CFD and simulation career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.