GATE Mechanical: Fluid Mechanics, previous-year questions solved, part 2

Part 2 of 2 of the Fluid Mechanics hub: 16 more official GATE ME questions on momentum, viscous and pipe flow, dimensional analysis, compressible flow and turbomachinery, each solved step by step and checked against the official answer key. Part 1 covers fluid statics, Bernoulli and flow measurement and fluid kinematics and the differential equations.

Questions from official GATE ME papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 16 of 32 questions on this page

GATE 2022 · ME Set-1 · Q.44MCQ · 2 marksMomentum, viscous and pipe flow, dimensional analysis

Gas accelerates from 100 to 170 m/s in a 1 m pipe with a 10 kPa drop. What force acts on the pipe?

Consider steady, one-dimensional compressible flow of a gas in a pipe of diameter 1 m. At one location in the pipe, the density and velocity are 1 kg/m3 and 100 m/s, respectively. At a downstream location in the pipe, the velocity is 170 m/s. If the pressure drop between these two locations is 10 kPa, the force exerted by the gas on the pipe between these two locations is ____________ N.
  1. (A)
  2. (B)
  3. (C)
  4. (D)3000

Answer: (B) Official key: B

  1. ; kg/s (the same at both sections).
  2. Momentum on the gas between the sections: .
  3. N.
  4. The gas pushes on the pipe with the opposite force: N in the flow direction (wall friction drags the pipe along).
Where this shows up in industry

This control-volume momentum balance is how engineers size pipe anchors and supports, and how they estimate the friction drag in gas lines. The same method gives jet-engine thrust and the forces on a nozzle.

GATE 2026 · ME · Q.53NAT · 2 marksMomentum, viscous and pipe flow, dimensional analysis

A diffuser raises condenser outlet water to atmospheric pressure. What force acts on its flange?

Water with a density of 1000 kg/m3 comes out of an industrial condenser through a horizontal pipe of 15 cm radius at the flow rate of 4.5 m3/min. The outlet of the pipe is connected to a coaxial diffuser of 0.5 m length using a flange to raise the pressure of water to atmospheric condition without any backflow. The inner radius (, in m) of the diffuser cross-section is expressed aswhere, represents the axial distance of the diffuser in m, from its inlet. Considering frictionless flow, the magnitude of the force exerted by the diffuser on the flange is ________ N (rounded off to 2 decimal places).

Answer: 16.30 N Official key: 15.50 to 17.10

  1. . Exit radius m.
  2. , ; m/s, m/s.
  3. Bernoulli with (gauge): Pa. The inlet is below atmospheric.
  4. Momentum on the water in the diffuser: , so N.
  5. The magnitude carried through the flange is 16.30 N.

Only the radius at the two ends matters; the profile in between does not change the answer for frictionless flow.

Where this shows up in industry

Diffusers recover pressure from velocity at pump outlets, in cooling-water lines and behind turbines (the draft tube). The momentum balance tells you what the flange bolts and supports must carry.

GATE 2022 · ME Set-1 · Q.43MCQ · 2 marksMomentum, viscous and pipe flow, dimensional analysis

A 0.1 mm lead bead sinks in a viscous liquid with C_D = 24/Re. What is its terminal velocity?

A solid spherical bead of lead (uniform density = 11000 kg/m3) of diameter = 0.1 mm sinks with a constant velocity in a large stagnant pool of a liquid (dynamic viscosity = kg·m−1·s−1). The coefficient of drag is given by , where the Reynolds number (Re) is defined on the basis of the diameter of the bead. The drag force acting on the bead is expressed as , where is the density of the liquid. Neglect the buoyancy force. Using = 10 m/s2, the velocity is __________ m/s.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. With , the drag simplifies to (Stokes' law). The liquid density cancels.
  2. Constant velocity: weight = drag, .
  3. m/s m/s.
Where this shows up in industry

Stokes settling sets how fast sand, swarf and abrasive particles drop out of coolant and lubricating oil, so it sizes settling tanks and filters. Particle-tracking (DPM) models in CFD use the same drag law at low Reynolds number.

GATE 2023 · ME · Q.19MCQ · 1 markMomentum, viscous and pipe flow, dimensional analysis

Laminar flow over a flat plate: how does wall shear at 30 mm compare with 15 mm?

Air (density = 1.2 kg/m3, kinematic viscosity = m2/s) flows over a flat plate with a free-stream velocity of 2 m/s. The wall shear stress at a location 15 mm from the leading edge is . What is the wall shear stress at a location 30 mm from the leading edge?
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. Check the regime: at 30 mm (and 2000 at 15 mm), far below the transition value of about . The boundary layer is laminar.
  2. Blasius: , so . The boundary layer thickens downstream and the velocity gradient at the wall falls.
  3. , so the shear is .

For scale: at 15 mm is about 0.0356 Pa.

Where this shows up in industry

Skin friction is highest near the leading edge, which is why heat transfer and wear also peak there. CFD engineers check their wall shear against the Blasius result on a flat plate before trusting a mesh's near-wall resolution on a real part.

GATE 2024 · ME · Q.37MCQ · 2 marksMomentum, viscous and pipe flow, dimensional analysis

Flow splits at a junction into pipes of length L, L and 10L. Is the long pipe's share Q/21?

In the pipe network shown in the figure, all pipes have the same cross-section and can be assumed to have the same friction factor. The pipes connecting points , , and with point have an equal length . The pipe connecting points and has a length . The pressures at the ends , , and are equal. The flow rate in the pipe connecting and is . Assume that the fluid flow is steady, incompressible, and the pressure losses at the pipe entrance and junction are negligible. Consider the following statements:
I : The flow rate in pipe connecting and is .
II: The pressure difference between and is equal to the pressure difference between and .
Which one of the following options is CORRECT?
Pipe network: flow Q enters at W and splits at junction J into three pipes ending at N, S (each length L) and E (length 10L); W to J is also length LWENSJQLLL10L
  1. (A)I is True and II is False
  2. (B)I is False and II is True
  3. (C)Both I and II are True
  4. (D)Both I and II are False

Answer: (B) Official key: B

  1. II is true: N, E and S are at the same pressure and all three pipes start at J, so .
  2. Darcy-Weisbach with the same and : . Equal gives , so .
  3. Continuity at J: , so , not . I is false.

is what you would get if were proportional to (laminar, Hagen-Poiseuille flow, where itself depends on ). With a fixed friction factor the drop goes as , and that is the trap.

Where this shows up in industry

Water-supply, HVAC duct and fire-sprinkler networks are balanced exactly this way (Hardy Cross and the solvers built on it). The long branch always gets more flow than a linear estimate suggests, which is why balancing valves are fitted on the short branches.

GATE 2025 · ME · Q.44MSQ · 2 marksMomentum, viscous and pipe flow, dimensional analysis

Fully developed pipe flow: which statements about velocity, Mach number and friction factor hold?

For a fully-developed pipe flow, which of the following options is/are correct?
  1. (A)For the same maximum velocity, the average velocity is higher in the turbulent regime than that of the laminar regime
  2. (B)Compressibility effects are important if Mach number is less than 0.3
  3. (C)For laminar flow, the friction factor is independent of surface roughness
  4. (D)For laminar flow, friction factor decreases with decrease in Reynolds number

Answer: (A; C) Official key: A; C

  • (A) True: the laminar parabola has . The turbulent profile is much flatter; the 1/7th power law gives .
  • (B) False: it's the other way round. Below Mach 0.3, density changes by under about 5%, and the flow is treated as incompressible.
  • (C) True: laminar , with no roughness term. The roughness bumps sit inside the viscous flow and don't trip it.
  • (D) False: increases as Re falls.
Where this shows up in industry

This is why engineers check Reynolds number before reaching for a Moody chart: oil in hydraulic lines and coolant in microchannels is often laminar, where wall finish doesn't change the pressure drop at all.

GATE 2023 · ME · Q.65NAT · 2 marksMomentum, viscous and pipe flow, dimensional analysis

Dimensional analysis: how does a blast wave's radius grow with time?

An explosion at time releases energy at the origin in a space filled with a gas of density . Subsequently, a hemispherical blast wave propagates radially outwards as shown in the figure.
Let denote the radius of the front of the hemispherical blast wave. The radius follows the relationship , where is a dimensionless constant. The value of exponent is ________.
(Rounded off to one decimal place)
A hemispherical blast wave of radius R spreading from an explosion of energy E at the origin on the ground, into a gas of density rhoERρ

Answer: 0.4 Official key: 0.39 to 0.41

  1. Dimensions: , , , .
  2. Match powers. M: . L: . T: .
  3. With : , so , and .

That is the Taylor-Sedov result . The hemispherical shape changes only the constant , not the exponents.

Where this shows up in industry

G. I. Taylor used this scaling to estimate the energy of the 1945 Trinity test from published photographs of the fireball. Energy-based blast scaling of the same kind underlies the scaled-distance rules for explosives storage and the blast estimates in pressure-vessel burst assessments.

GATE 2024 · ME · Q.51NAT · 2 marksMomentum, viscous and pipe flow, dimensional analysis

Dimensional analysis: how does capillary filling distance depend on surface tension?

A liquid fills a horizontal capillary tube whose one end is dipped in a large pool of the liquid. Experiments show that the distance travelled by the liquid meniscus inside the capillary in time is given by , where is the surface tension, is the inner radius of the capillary, and is the dynamic viscosity of the liquid. If is a dimensionless constant, then the exponent is __________ (rounded off to 1 decimal place).

Answer: 0.5 Official key: 0.5 to 0.5

  1. Dimensions: , , , .
  2. Match powers on both sides. M: . L: . T: .
  3. Substituting into the T equation: , so , with and .

That is the Lucas-Washburn law, .

Where this shows up in industry

Washburn's law governs wicking: in heat-pipe wicks, paper test strips and ink feeding a printhead. It is also a first estimate for how far resin soaks into a fibre bundle during composite manufacturing.

GATE 2025 · ME · Q.17MCQ · 1 markMomentum, viscous and pipe flow, dimensional analysis

A 1:100 Froude-scaled bridge pier model runs at 1 m/s. What is the prototype velocity?

In a laboratory experiment using a scaled down model to measure scour at a bridge pier, the Froude number is important. The ratio of the prototype length to the model length is 100. If the velocity of the model is 1 m s−1, the velocity (in m s−1) of the prototype is
  1. (A)0.1
  2. (B)1
  3. (C)10
  4. (D)100

Answer: (C) Official key: C

  1. Froude similarity: is the same for model and prototype, with the same in both.
  2. .
  3. 10 m/s.
Where this shows up in industry

Ship hulls, spillways and harbour models are tested at Froude similarity because gravity waves dominate. Reynolds number can't be matched at the same time with water in both, so towing-tank results get a separate friction correction.

GATE 2022 · ME Set-1 · Q.30MSQ · 1 markCompressible flow

A convergent nozzle is choked. What happens when the inlet pressure is raised?

The figure shows a purely convergent nozzle with a steady, inviscid compressible flow of an ideal gas with constant thermophysical properties operating under choked condition. The exit plane shown in the figure is located within the nozzle. If the inlet pressure () is increased while keeping the back pressure () unchanged, which of the following statements is/are true?
  1. (A)Mass flow rate through the nozzle will remain unchanged.
  2. (B)Mach number at the exit plane of the nozzle will remain unchanged at unity.
  3. (C)Mass flow rate through the nozzle will increase.
  4. (D)Mach number at the exit plane of the nozzle will become more than unity.

Answer: (B, C) Official key: B, C

  • A purely convergent nozzle can accelerate a gas only up to Mach 1, reached at the exit (the throat). Raising can't push the exit Mach number past 1, so (B) is true and (D) is false.
  • Choked mass flow is It is fixed only for fixed inlet conditions and grows in proportion to , so (C) is true and (A) is false.

"Choked" means lowering the back pressure no longer increases the flow. Raising the inlet pressure still does: the gas at the throat is simply denser.

Where this shows up in industry

Safety relief valves, gas-cylinder regulators and orifice flow restrictors rely on this: once choked, flow depends only on upstream pressure and temperature, so a sonic orifice makes a simple, accurate flow meter.

GATE 2022 · ME Set-2 · Q.24MCQ · 1 markCompressible flow

Supersonic flow enters a diverging channel, and pressure downstream is higher. Why?

Consider a steady flow through a horizontal divergent channel, as shown in the figure, with supersonic flow at the inlet. The direction of flow is from left to right. Pressure at location B is observed to be higher than that at an upstream location A. Which among the following options can be the reason?
Horizontal diverging channel with flow from left to right; point A upstream, point B downstreamAB
  1. (A)Since volume flow rate is constant, velocity at B is lower than velocity at A
  2. (B)Normal shock
  3. (C)Viscous effect
  4. (D)Boundary layer separation

Answer: (B) Official key: B

In isentropic supersonic flow the area-velocity relation says a growing area speeds the flow up, so pressure should fall from A to B. A pressure rise means the flow left the isentropic path: a normal shock between A and B jumps the flow to subsonic, raising the pressure, and the subsonic flow then decelerates further in the diverging section.

(A) treats the gas as incompressible: in a compressible flow the mass flow rate is constant, not the volume flow rate. The official key accepts only (B).

Where this shows up in industry

Engineers designing rocket nozzles and supersonic wind tunnels watch for exactly this: when the back pressure is too high, a shock sits inside the diverging section, the flow behind it can separate, and thrust or test conditions are lost.

GATE 2023 · ME · Q.20MCQ · 1 markCompressible flow

Air at 400 m/s enters a duct whose area doubles. Do velocity and pressure rise or fall?

Consider an isentropic flow of air (ratio of specific heats = 1.4) through a duct as shown in the figure.
The variations in the flow across the cross-section are negligible. The flow conditions at Location 1 are given as follows:
kPa, kg/m3, m/s
The duct cross-sectional area at Location 2 is given by , where denotes the duct cross-sectional area at Location 1. Which one of the given statements about the velocity and pressure at Location 2 is TRUE?
Diverging duct with flow from left to right: Location 1 with density rho1, pressure P1, velocity u1, area A1; downstream Location 2 with rho2, P2, u2 and area A2ρ1P1u1A1ρ2P2u2A2Location 1Location 2
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. Check the Mach number first: m/s, so . The flow is supersonic.
  2. Area-velocity relation: . With , a growing area accelerates the flow, and in isentropic flow pressure falls as velocity rises.
  3. Numbers: , so , giving on the supersonic branch, m/s and kPa.
  4. So and : option (C).

Treating the air as subsonic (or incompressible) gives (B), the trap. Always compute the Mach number before using intuition about ducts.

Where this shows up in industry

This is how the diverging section of a rocket nozzle or supersonic wind tunnel works: once the flow is past Mach 1, more area means more speed. Nozzle designers size the exit-to-throat area ratio from the same relation to hit a target exit Mach number.

GATE 2024 · ME · Q.40MSQ · 2 marksCompressible flow

A normal shock stands in the diverging part of a nozzle. How do properties change across it?

Steady, compressible flow of air takes place through an adiabatic converging-diverging nozzle, as shown in the figure. For a particular value of pressure difference across the nozzle, a stationary normal shock wave forms in the diverging section of the nozzle. If and denote the flow conditions just upstream and downstream of the normal shock, respectively, which of the following statement(s) is/are TRUE?
  1. (A)Static pressure at E is lower than the static pressure at F
  2. (B)Density at E is lower than the density at F
  3. (C)Mach number at E is lower than the Mach number at F
  4. (D)Specific entropy at E is lower than the specific entropy at F

Answer: (A; B; D) Official key: A; B; D

Across a normal shock the flow goes from supersonic () to subsonic () in a very thin, irreversible layer.

  • Static pressure, density and temperature all jump up: (A) and (B) true.
  • Mach number drops: (C) false.
  • The shock is adiabatic but irreversible, so entropy rises (and stagnation pressure falls): (D) true.
Where this shows up in industry

The stagnation-pressure loss across a shock is why supersonic intakes on jet engines use a series of weaker oblique shocks before a final normal shock, recovering more pressure than a single strong shock would.

GATE 2026 · ME · Q.25MCQ · 1 markCompressible flow

Gas flows isothermally down a long pipe. Does its average velocity rise or fall?

An ideal gas passes isothermally through a long horizontal uniform cross-section pipe under steady flow. Consider that the pressure gradient in the pipe is sufficient for a finite change in the density of the gas. If the flow of the gas is purely pressure driven and subsonic throughout, then the average flow velocity
  1. (A)increases along the flow
  2. (B)decreases along the flow
  3. (C)does not change throughout the pipe
  4. (D)increases in the hydrodynamic entrance region and then decreases thereafter

Answer: (A) Official key: A

  1. The flow is pressure driven, so pressure falls along the pipe.
  2. Isothermal ideal gas: , so density falls in step with pressure.
  3. Steady flow in a uniform pipe: is constant, so increases along the flow.
Where this shows up in industry

Long natural-gas pipelines run close to isothermal (the ground keeps the temperature steady), and the gas really does speed up downstream. Pipeline engineers have to account for this in pressure-drop and compressor-spacing calculations.

GATE 2025 · ME · Q.53NAT · 2 marksTurbomachinery

At what rpm does a 1 m Pelton wheel give maximum power with a 125.66 m/s jet?

Consider a Pelton wheel of 1 m diameter. The magnitude of relative velocity of water at the bucket inlet is same as the magnitude of relative velocity of water at the bucket exit. The absolute speed of water at the bucket inlet is 125.66 m s−1. For maximum power output from the Pelton wheel, the rpm of the Pelton wheel is __________________ (rounded off to 1 decimal place).

Answer: 1200.0 rpm Official key: 1197 to 1203

  1. With no friction in the bucket (equal relative velocities), the power per unit mass flow is proportional to , where is the bucket speed and the jet speed.
  2. is largest at m/s.
  3. 1200.0 rpm.
Where this shows up in industry

Real Pelton wheels run at a speed ratio of about 0.45-0.47, slightly below the ideal 0.5, because of bucket friction and losses. Hydro plants pick the number of jets and the wheel diameter so that this speed matches a synchronous generator speed.

GATE 2026 · ME · Q.58NAT · 2 marksTurbomachinery

An inward-flow reaction turbine runs at 600 rpm with a 15° guide blade angle. What is the runner vane angle?

An inward flow reaction turbine, having an outer diameter of 1 m, runs at 600 RPM. The normal component of absolute velocity at the inlet is 10 m/s. If the guide blade angle is 15°, then the inlet vane angle of the runner is ________ degree (rounded off to 1 decimal place).

Answer: 59.4° Official key: 57.5 to 61.5

  1. Blade speed at inlet: m/s.
  2. The guide blade angle sets the direction of the absolute velocity: m/s.
  3. The inlet velocity triangle gives the runner vane angle: .
  4. 59.4°.
Where this shows up in industry

Velocity triangles are the first step in designing any turbine, pump or compressor stage. CFD of a Francis runner then checks that the flow actually meets the vane at this angle, because a mismatch causes shock losses and cavitation at the leading edge.

From GATE prep to a CFD and fluids career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.