GATE Mechanical: Machining, Metrology, CNC and Additive Manufacturing, previous-year questions solved

Real manufacturing questions from the last four GATE Mechanical papers: Merchant's circle and cutting forces, Taylor tool life and machining economics, milling and grinding, ECM, EDM and ultrasonic machining, limits and fits, the best-size wire, surface roughness, CNC drives and G codes, fixtures and additive manufacturing. Each one has a step-by-step solution that matches the official answer key, and a note on where the idea is used in machine shops, inspection rooms and 3D printing labs.

Questions from official GATE ME papers (IIT Kharagpur 2022, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 26 questions

GATE 2022 · ME Set-1 · Q.54NAT · 2 marksMachining mechanics, tool life and economics

Orthogonal turning at 4 m/s with friction angle 45° and shear angle 25°: what is the cutting force?

Under orthogonal cutting condition, a turning operation is carried out on a metallic workpiece at a cutting speed of 4 m/s. The orthogonal rake angle of the cutting tool is 5º. The uncut chip thickness and width of cut are 0.2 mm and 3 mm, respectively. In this turning operation, the resulting friction angle and shear angle are 45º and 25º, respectively. If the dynamic yield shear strength of the workpiece material under this cutting condition is 1000 MPa, then the cutting force is ______________ N (round off to one decimal place).

Answer: 2573.4 N Official key: 2570.0 to 2576.0

  1. Shear plane area: .
  2. Shear force: .
  3. Merchant's circle: the resultant makes angle with the shear plane and with the cutting direction, so
  4. .

The cutting speed (4 m/s) is not needed for the force; it would be needed for power (). Stopping at the shear force (1419.7 N) is the common slip.

Where this shows up in industry

Tool makers and process planners use the same force model to size spindle power, pick insert geometry and set clamping forces. In practice the shear strength and friction angle are not looked up: they are back-calculated from dynamometer tests (piezoelectric force plates under the tool) for each work material and tool coating.

GATE 2022 · ME Set-2 · Q.55NAT · 2 marksMachining mechanics, tool life and economics

Cutting and thrust forces are equal, rake 0°, shear angle 15°: what is the cutting force?

In an orthogonal machining operation, the cutting and thrust forces are equal in magnitude. The uncut chip thickness is 0.5 mm and the shear angle is 15°. The orthogonal rake angle of the tool is 0° and the width of cut is 2 mm. The workpiece material is perfectly plastic and its yield shear strength is 500 MPa. The cutting force is _________ N (round off to the nearest integer).

Answer: 2732 N Official key: 2700 to 2750

  1. Shear force needed to shear the material on the shear plane: .
  2. Resolve the measured forces along the shear plane: .
  3. With : , so .

Equal forces with zero rake mean a friction angle of 45°. Merchant's angle relation would then predict , not 15°: the question gives the measured shear angle, so use it and do not replace it with Merchant's prediction.

Where this shows up in industry

The gap between the measured shear angle and Merchant's prediction is normal: real chips form in a shear zone, not on a plane, and friction on the rake face is not Coulomb friction. That is why machining simulation software (finite element chip formation models) uses measured flow-stress data instead of the classic angle relation.

GATE 2022 · ME Set-1 · Q.55NAT · 2 marksMachining mechanics, tool life and economics

A 1 mm wall, 100 mm tube is turned at 1 m/min axial feed with u = 6 J/mm³: what power is needed?

A 1 mm thick cylindrical tube, 100 mm in diameter, is orthogonally turned such that the entire wall thickness of the tube is cut in a single pass. The axial feed of the tool is 1 m/minute and the specific cutting energy () of the tube material is 6 J/mm3. Neglect contribution of feed force towards power. The power required to carry out this operation is _________ kW (round off to one decimal place).

Answer: 31.4 kW Official key: 30.0 to 32.0

  1. The tool faces the end of the tube: in each second it advances along the axis and removes an annulus of area .
  2. Material removal rate: .
  3. Power .

Using the mean diameter (99 mm) gives 31.1 kW, also inside the key. The spindle speed is not needed: the axial feed rate alone fixes the volume removed per second.

Where this shows up in industry

Specific cutting energy is the quickest way to check whether a machine can take a cut. Typical textbook values are about 0.4-1.1 J/mm3 for aluminium alloys, 2.7-9.3 for steels and 3-4 for titanium alloys; the motor must supply the cutting power divided by the spindle drive efficiency.

GATE 2022 · ME Set-2 · Q.54NAT · 2 marksMachining mechanics, tool life and economics

A 4-tooth slab mill cuts at depth D/2, so the small-depth chip formula fails: what is the maximum cutting force?

A straight-teeth horizontal slab milling cutter is shown in the figure. It has 4 teeth and diameter () of 200 mm. The rotational speed of the cutter is 100 rpm and the linear feed given to the workpiece is 1000 mm/minute. The width of the workpiece () is 100 mm, and the entire width is milled in a single pass of the cutter. The cutting force/tooth is given by , where specific cutting force , is the width of cut, and is the uncut chip thickness.
The depth of cut () is , and hence the assumption of is invalid. The maximum cutting force required is ________ kN (round off to one decimal place).
Horizontal slab milling: a 200 mm diameter cutter with its lowest point on the machined surface; the workpiece top is D/2 = 100 mm above that surface, so the depth of cut is half the cutter diameterDd = D/2workpiece100 rpmfeed 1000 mm/minmachined surface

Answer: 2.5 kN Official key: 2.4 to 2.6

  1. Feed per tooth: .
  2. A tooth at angle from the bottom of the cut removes a chip . It stays in the cut while , that is up to .
  3. The thickest chip is at : .
  4. The 4 teeth are 90° apart, so when one tooth is at 90° the next is at 0° with zero chip: only one tooth carries load. .

The small-depth formula gives 3.54 kN: that is why the question warns that does not hold. (We also swept the cutter through a full turn in steps of 0.01° and summed every engaged tooth: the peak is 2.50 kN.)

Where this shows up in industry

With straight teeth and wide engagement, each tooth slams in and out of the cut, so the force swings from zero to its peak every tooth pass: a recipe for chatter. That is why slab mills have helical teeth (the load passes smoothly from one tooth to the next) and why production shops mostly use face mills with indexable inserts instead.

GATE 2024 · ME · Q.60NAT · 2 marksMachining mechanics, tool life and economics

Tool life is 60 min at 60 m/min and 10 min at 100 m/min: what is it at 80 m/min?

A cutting tool provides a tool life of 60 minutes while machining with the cutting speed of 60 m/min. When the same tool is used for machining the same material, it provides a tool life of 10 minutes for a cutting speed of 100 m/min. If the cutting speed is changed to 80 m/min for the same tool and work material combination, the tool life computed using Taylor’s tool life model is____________ minutes (rounded off to 2 decimal places).

Answer: 21.87 min Official key: 21.00 to 22.50

  1. Taylor: . From the two tests: , so and .
  2. .
  3. At 80 m/min: .

Interpolating tool life linearly between the two tests gives 35 min, far too high: tool life falls steeply (as a power law) with speed, so the curve sags between the points.

Where this shows up in industry

A Taylor exponent near 0.29, as here, is typical of carbide tools (textbook ranges are roughly 0.1-0.2 for HSS, 0.2-0.5 for carbide and 0.5-0.7 for ceramics). Tooling catalogues publish speed tables that come from exactly this kind of fit, often for 15 minutes of tool life.

GATE 2024 · ME · Q.64NAT · 2 marksMachining mechanics, tool life and economics

Slab milling a 100 mm long face with a 100 mm, 8-tooth cutter at 20 m/min: how long does it take?

A flat surface of a C60 steel having dimensions of 100 mm (length) × 200 mm (width) is produced by a HSS slab mill cutter. The 8-toothed cutter has 100 mm diameter and 200 mm width. The feed per tooth is 0.1 mm, cutting velocity is 20 m/min and depth of cut is 2 mm. The machining time required to remove the entire stock is _____________ minutes (rounded off to 2 decimal places).

Answer: 2.24 min Official key: 2.20 to 2.65

  1. Spindle speed: .
  2. Table feed: .
  3. The cutter must travel past the work by the approach length before the full depth is cut.
  4. . The cutter is as wide as the face, so one pass does it.

Adding the approach at both ends gives 2.51 min, also inside the key. Leaving the approach out gives 1.96 min, which is outside it.

Where this shows up in industry

CAM software estimates cycle time the same way, adding approach and overrun to every pass. On a slab mill the approach is large ({st24_A:.0f} mm here against a 100 mm part), which is one reason face milling, whose approach is only about the cutter radius past the edge, is often faster on short parts.

GATE 2025 · ME · Q.63NAT · 2 marksMachining mechanics, tool life and economics

Turning at 25 m/min with C = 75 and n = 0.25: what is the tool changing cost per piece?

Cylindrical workpieces of diameter 60 mm and length 400 mm are machined on a lathe at a cutting speed of 25 m min-1 and a feed of 0.2 mm rev-1. The Taylor’s tool life parameters and for this setup are 75 and 0.25, respectively. The tool changing time is 3 minutes. With a labor and overhead cost of ₹ 5 per minute, the tool changing cost per piece is ₹ _______ (rounded off to 2 decimal places).

Answer: ₹ 2.79 Official key: 2.65 to 2.95

  1. Tool life: .
  2. Machining time per piece: , .
  3. Pieces per tool life: , so each piece carries of a tool change.
  4. Cost per piece ₹ .

Rounding down to 5 whole pieces per tool gives ₹ 3.00, outside the key: the key uses the fractional number of pieces per tool life.

Where this shows up in industry

This term is one part of the cost per piece; the others are machining time, idle time and the tool cost per edge. Balancing them gives the minimum-cost cutting speed, which is why shops running expensive machines push speeds up and accept shorter tool life.

GATE 2026 · ME · Q.63NAT · 2 marksMachining mechanics, tool life and economics

Feed 0.24 mm/rev, uncut chip 0.23 mm, Fc 800 N, radial 150 N, shear angle 20°: what is the shear force?

During orthogonal turning by using a single point cutting tool, feed rate is 0.24 mm/rev. The uncut chip thickness is 0.23 mm. The shear angle, tangential force component, and radial force component are 20°, 800 N, and 150 N, respectively. The value of shear force is ________ N (rounded off to 2 decimal places).

Answer: 572.15 N Official key: 571.00 to 574.00

  1. The uncut chip thickness is smaller than the feed, so the cutting edge is inclined: , giving and ().
  2. The thrust force acts normal to the cutting edge in the horizontal plane; the dynamometer's radial component is , so .
  3. Shear force: .

Using the 150 N radial force directly as the thrust force gives 700.5 N, outside the key. The feed and the chip thickness are given exactly so that you correct for the edge angle.

Where this shows up in industry

A lathe dynamometer reports three components: tangential (cutting), feed (axial) and radial. Which of them equals the thrust force of the textbook orthogonal model depends on the tool's approach angle, so force data from tool makers always quotes the insert's lead angle.

GATE 2026 · ME · Q.64NAT · 2 marksMachining mechanics, tool life and economics

A drill makes 150 holes at 200 rpm but only 60 at 300 rpm: what is the Taylor exponent?

A drill bit during its lifetime can produce 150 through holes in a plate at a drill-speed of 200 RPM. If the drill-speed increases to 300 RPM, then it can produce 60 through holes in the same plate before the drill bit fails. Assume all other parameters remain constant. The value of the exponent in Taylor’s tool life equation is ________ (rounded off to 2 decimal places).

Answer: 0.31 Official key: 0.29 to 0.33

  1. Cutting speed is proportional to rpm. With the same feed per revolution and the same hole depth, time per hole is proportional to , so tool life in minutes is .
  2. , .
  3. : , so .

Using the hole counts directly as tool life () gives , outside the key: at higher rpm each hole takes less time, so 60 holes is far less than 2/5 of the minutes.

Where this shows up in industry

Production lines count tool life in parts or holes, not minutes. Tool management on a CNC machine counts holes per drill and swaps the drill at a set number, chosen well below the failure point, because a drill that breaks inside a hole can scrap an engine block.

GATE 2024 · ME · Q.30MCQ · 1 markMachining mechanics, tool life and economics

Which grinding wheel gives the best surface finish: A36L5V, A54L5V, A60L5V or A80L5V?

The grinding wheel used to provide the best surface finish is
  1. (A)A36L5V
  2. (B)A54L5V
  3. (C)A60L5V
  4. (D)A80L5V

Answer: (D) Official key: D

  1. Read the standard marking: A = aluminium oxide abrasive, the number = grit size, L = grade (bond hardness), 5 = structure (spacing), V = vitrified bond.
  2. All four wheels are identical except the grit number. A higher grit number means finer abrasive grains, each grain takes a smaller scratch, and the surface is smoother.
  3. The finest grit is 80: option (D), A80L5V.
Where this shows up in industry

Coarse wheels (24-46 grit) are used for fast stock removal and fine ones (80-120, and finer for tool and cutter grinding) for finish. Bearing races, crankshaft journals and hydraulic spool valves are finish-ground to a few tenths of a micrometre Ra.

GATE 2022 · ME Set-1 · Q.33NAT · 1 markNon-traditional machining

ECM removes 100 mg/s of copper. Under identical conditions, how much aluminium does it remove?

Electrochemical machining operations are performed with tungsten as the tool, and copper and aluminum as two different workpiece materials. Properties of copper and aluminum are given in the table below.
MaterialAtomic mass (amu)ValencyDensity (g/cm3)
Copper6329
Aluminum2732.7
Ignore overpotentials, and assume that current efficiency is 100% for both the workpiece materials. Under identical conditions, if the material removal rate (MRR) of copper is 100 mg/s, the MRR of aluminum will be ________________ mg/s (round-off to two decimal places).

Answer: 28.57 mg/s Official key: 27.00 to 30.00

  1. Faraday's law: mass removed per second . Identical conditions means the same current , so .
  2. Copper: . Aluminium: .
  3. .

The density is a distractor: it matters only if the MRR is asked as a volume. Using the volume ratio gives 95.2 mg/s and ignoring valency gives 42.9 mg/s, both outside the key.

Where this shows up in industry

ECM dissolves metal atom by atom, so the tool never wears and leaves no heat-affected zone or burr. It is used to shape jet-engine compressor and turbine blades, rifle gun barrels and deburr cross-drilled holes in fuel injectors and hydraulic valve bodies.

GATE 2022 · ME Set-2 · Q.28MSQ · 1 markNon-traditional machining

Which of ECM, EDM, laser beam and electron beam machining remove metal by melting it?

Which of these processes involve(s) melting in metallic workpieces?
  1. (A)Electrochemical machining
  2. (B)Electric discharge machining
  3. (C)Laser beam machining
  4. (D)Electron beam machining

Answer: (B, C, D) Official key: B, C, D

  1. EDM: each spark heats a tiny spot above the melting (and boiling) point; the molten crater is flushed away by the dielectric.
  2. Laser and electron beams focus energy into a small spot and melt and vaporise the metal.
  3. ECM removes metal by anodic dissolution in an electrolyte: an electrochemical reaction, no melting.

Answer: (B), (C) and (D).

Where this shows up in industry

Every thermal process leaves a thin re-solidified 'recast' layer with microcracks. For fatigue-critical parts such as turbine blades and landing gear, that layer is removed or controlled; ECM is chosen when no thermal damage at all is allowed.

GATE 2025 · ME · Q.24MCQ · 1 markNon-traditional machining

Which process machines ceramics and glass: EDM, USM, ECM or plasma arc?

Ceramics and glass are machined by
  1. (A)electric discharge machining
  2. (B)ultrasonic machining
  3. (C)electrochemical machining
  4. (D)transferred arc plasma machining

Answer: (B) Official key: B

  1. Ceramics and glass do not conduct electricity, so EDM (spark between tool and work), ECM (work is the anode) and transferred-arc plasma (arc to the work) cannot run.
  2. Ultrasonic machining hammers abrasive grains into the surface at about 20 kHz; hard, brittle materials chip away in tiny fractures. That suits glass and ceramics: option (B).
Where this shows up in industry

Rotary ultrasonic machining (a diamond tool that both spins and vibrates) drills holes in alumina, silicon carbide, glass and carbon-fibre composites with less chipping at the exit than plain diamond drilling.

GATE 2022 · ME Set-1 · Q.20MCQ · 1 markMetrology, fits and surface finish

Shaft 25.0 ± 0.010 mm in a hole 25.015 ± 0.015 mm: what type of fit is it?

The type of fit between a mating shaft of diameter mm and a hole of diameter mm is __________.
  1. (A)Clearance
  2. (B)Transition
  3. (C)Interference
  4. (D)Linear

Answer: (B) Official key: B

  1. Shaft limits: 24.990 to 25.010 mm. Hole limits: 25.000 to 25.030 mm.
  2. Largest gap (smallest shaft in largest hole): clearance.
  3. Tightest case (largest shaft in smallest hole): , an interference.
  4. Depending on the actual sizes the pair can have clearance or interference: a transition fit, option (B).
Where this shows up in industry

Transition fits locate parts accurately without a press: ISO H7/k6 or H7/m6 are typical for gears, pulleys and couplings keyed to shafts, and for rolling-bearing inner rings on rotating shafts. Bearing makers' catalogues list the recommended shaft tolerance class for each load case.

GATE 2025 · ME · Q.25MCQ · 1 markMetrology, fits and surface finish

Hole 30 +0.030/+0.000 and shaft 30 +0.020/−0.020: loose, interference, transition or clearance fit?

When assembled, the hole mm and shaft mm will result in
  1. (A)loose fit
  2. (B)interference fit
  3. (C)transition fit
  4. (D)clearance fit

Answer: (C) Official key: C

  1. Hole: 30.000 to 30.030 mm. Shaft: 29.980 to 30.020 mm.
  2. Maximum clearance: . Maximum interference: .
  3. Both can occur, so it is a transition fit: option (C).

'Loose fit' and 'clearance fit' are the same thing; the two options cancel each other out.

Where this shows up in industry

A shaft tolerance that straddles the basic size (±0.020 here) is the hallmark of a transition fit. It is the usual choice for dowel pins in fixtures and for locating spigots where parts must come apart for service.

GATE 2022 · ME Set-2 · Q.20MCQ · 1 markMetrology, fits and surface finish

Shaft 25 −0.04/−0.07 in hole 25 +0.02/−0.00: match allowance, maximum clearance and the hole's MML

A shaft of diameter mm is assembled in a hole of diameter mm. Match the allowance and limit parameter in Column I with its corresponding quantitative value in Column II for this shaft-hole assembly.
Allowance and limit parameter (Column I)Quantitative value (Column II)
P. Allowance1. 0.09 mm
Q. Maximum clearance2. 24.96 mm
R. Maximum material limit for hole3. 0.04 mm
4. 25.0 mm
  1. (A)P-3, Q-1, R-4
  2. (B)P-1, Q-3, R-2
  3. (C)P-1, Q-3, R-4
  4. (D)P-3, Q-1, R-2

Answer: (A) Official key: A

  1. Shaft: 24.93 to 24.96 mm. Hole: 25.00 to 25.02 mm.
  2. Allowance = minimum clearance = smallest hole − largest shaft → 3.
  3. Maximum clearance = largest hole − smallest shaft → 1.
  4. Maximum material limit of a hole is its smallest size (most metal left): 25.00 mm → 4.

P-3, Q-1, R-4: option (A). 24.96 mm is the maximum material limit of the shaft, not the hole.

Where this shows up in industry

Maximum material condition is what functional gauges check: a GO plug gauge is made at the hole's MML (25.00 mm here) and a GO ring at the shaft's MML (24.96 mm). GD&T uses the same idea with the Ⓜ modifier, which grants bonus tolerance as a part departs from MMC.

GATE 2022 · ME Set-2 · Q.56NAT · 2 marksMetrology, fits and surface finish

Best size wire for a metric thread of 4 mm pitch: what diameter touches the flanks on the pitch line?

The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch () and included angle of the thread are 4 mm and 60º, respectively. The diameter of the best size wire is ___________ mm (round off to 2 decimal places).
Metric thread groove with a 60 degree included angle and pitch p; a best-size wire sits in the groove and touches both flanks exactly on the pitch line, 0.25p either side of the groove axis; the crest is 0.5p from the groove axisPitch lineWire0.25p0.5p60°Flank

Answer: 2.31 mm Official key: 2.29 to 2.33

  1. At the pitch line the groove is wide, so each contact point is from the groove axis.
  2. The wire radius at a contact point is perpendicular to the flank. The flank makes with the vertical, so the radius makes with the horizontal: .
  3. .

For a 60° thread this is the familiar .

Where this shows up in industry

This is the three-wire method: three best-size wires go into the thread, a micrometer measures over them, and the pitch diameter is calculated. Best size is chosen because touching at the pitch line makes the result insensitive to small errors in the flank angle; calibration labs use it to certify thread plug gauges.

GATE 2026 · ME · Q.33MCQ · 1 markMetrology, fits and surface finish

A stylus profile shows 10 peaks and 10 valleys: what is the ten-point height?

A two-dimensional surface profile is obtained over a sampling length by using a contact type stylus profilometer as shown in the figure below. A line AA parallel to the general lay of the trace is considered. The true heights from AA to the peaks and valleys (in μm) in the trace are also shown in the figure (not to scale).
The ten-point height average in μm is
Heights from AA in the figure, left to right: peaks 5.35, 6.7, 5.28, 4.32, 8.3, 6.3, 4.96, 6.9, 6.2, 5.54; valleys 2.81, 1.92, 3.71, 2.82, 4.2, 1.97, 2.01, 2.9, 4.26, 4.3 (listed here for small screens).
Surface profile trace over one sampling length above a reference line AA. Peak heights from AA in micrometres, left to right: 5.35, 6.7, 5.28, 4.32, 8.3, 6.3, 4.96, 6.9, 6.2, 5.54. Valley heights: 2.81, 1.92, 3.71, 2.82, 4.2, 1.97, 2.01, 2.9, 4.26, 4.3AA5.352.816.71.925.283.714.322.828.34.26.31.974.962.016.92.96.24.265.544.3μm
  1. (A)4.57
  2. (B)5.99
  3. (C)3.09
  4. (D)2.90

Answer: (A) Official key: A

  1. Ten-point height: the mean of the five highest peaks minus the mean of the five lowest valleys, all measured from the same line AA.
  2. Five highest peaks: .
  3. Five lowest valleys: .
  4. : option (A).

The distractors are other averages of the same trace: (B) is the mean of all ten peaks (5.985), (C) the mean of all ten valleys (3.09) and (D) their difference (2.895).

Where this shows up in industry

This ten-point height was ISO's Rz until 1997; the current ISO Rz is the mean maximum peak-to-valley height over five sampling lengths, and Japan's standard renamed the old one RzJIS. On a drawing, check which Rz is meant: the two can differ noticeably on the same surface.

GATE 2022 · ME Set-1 · Q.19MCQ · 1 markCNC machines and fixtures

A stepper needs 600 pulses per revolution on a 5 mm lead screw: what pulse rate moves the table at 5 m/min?

A CNC worktable is driven in a linear direction by a lead screw connected directly to a stepper motor. The pitch of the lead screw is 5 mm. The stepper motor completes one full revolution upon receiving 600 pulses. If the worktable speed is 5 m/minute and there is no missed pulse, then the pulse rate being received by the stepper motor is
  1. (A)20 kHz
  2. (B)10 kHz
  3. (C)3 kHz
  4. (D)15 kHz

Answer: (B) Official key: B

  1. Screw speed: .
  2. Pulse rate: : option (B).

Each pulse moves the table , the basic length unit of this axis.

Where this shows up in industry

Open-loop stepper drives like this run hobby CNC routers, laser engravers and 3D printers: cheap, but a missed step goes unnoticed. Industrial machine tools use servo motors with encoders (closed loop) on preloaded ball screws, so the control knows the true position.

GATE 2022 · ME Set-2 · Q.22MCQ · 1 markCNC machines and fixtures

Which one cannot give linear motion in a CNC machine: linear motor, ball screw, lead screw or chain and sprocket?

Which one of the following CANNOT impart linear motion in a CNC machine?
  1. (A)Linear motor
  2. (B)Ball screw
  3. (C)Lead screw
  4. (D)Chain and sprocket

Answer: (D) Official key: D

  1. Linear motors drive the slide directly; ball screws and lead screws convert motor rotation into precise slide travel. All three are used on CNC axes.
  2. A chain and sprocket transmits rotation between shafts. It has slack, stretch and the polygon effect (speed ripples as each link wraps the sprocket), so it cannot position a CNC slide: option (D).
Where this shows up in industry

High-speed machining centres and laser cutters use linear motors for fast, backlash-free axes; most machining centres use preloaded ball screws, whose rolling balls give high efficiency and almost no backlash, unlike a plain sliding lead screw.

GATE 2024 · ME · Q.33MCQ · 1 markCNC machines and fixtures

Which letter denotes preparatory functions in CNC part programming?

The preparatory functions in Computer Numerical Controlled (CNC) machine programing are denoted by the alphabet
  1. (A)G
  2. (B)M
  3. (C)P
  4. (D)O

Answer: (A) Official key: A

  1. Preparatory functions set up how the axes move: G00 rapid traverse, G01 linear interpolation, G02/G03 circular arcs, G90/G91 absolute or incremental. They are the G codes: option (A).
  2. M codes are miscellaneous (machine) functions such as M03 spindle on clockwise, M05 spindle stop, M06 tool change, M30 program end. O is the program number; P is a parameter, for example a dwell time.
Where this shows up in industry

ISO 6983 defines this G and M code format, and Fanuc-style controls follow it closely. CAM software generates the code, but setters still read and edit it at the machine, so G and M codes come up in almost every CNC programmer interview.

GATE 2026 · ME · Q.32MCQ · 1 markCNC machines and fixtures

A 205 mm tall workpiece is slab milled on top: how tall should the fixture be?

A work piece is to be firmly held in a fixture. It is to be machined by using a plain slab milling cutter as shown in the figure below.
Which one of the following options is the most suitable value of height H of the fixture in mm?
A 100 mm wide work piece 205 mm tall stands between two fixture blocks of height H; a plain slab milling cutter machines its top face while the table feeds horizontallyPlain slabmilling cutter205 mmWork pieceH100 mmFixtureFixtureFeednot to scale
  1. (A)200
  2. (B)210
  3. (C)150
  4. (D)70

Answer: (A) Official key: A

  1. The cutter machines the top of the 205 mm tall work piece, so the fixture must stay below the cut: at 210 mm (B) the cutter would hit the fixture.
  2. The work piece is tall and narrow (205 mm against 100 mm wide). The cutting force acts at the top, so the support should reach as close to the cut as possible; a 150 mm or 70 mm fixture leaves a long overhang that bends and chatters.
  3. The tallest fixture that still clears the cutter is 200 mm: option (A).
Where this shows up in industry

Fixture designers follow the same two rules: clamp and support close to the cutting zone, and keep every fixture element out of the tool path (checked in CAM with a fixture model). Tall thin parts are often given extra supports or machined in stages to avoid chatter.

GATE 2022 · ME Set-1 · Q.28MSQ · 1 markAdditive manufacturing

Which additive manufacturing processes can use wire as the feedstock?

Which of the following additive manufacturing technique(s) can use a wire as a feedstock material?
  1. (A)Stereolithography
  2. (B)Fused deposition modeling
  3. (C)Selective laser sintering
  4. (D)Directed energy deposition processes

Answer: (B, D) Official key: B, D

  1. Fused deposition modelling feeds a thin polymer filament (a wire) into a heated nozzle.
  2. Directed energy deposition melts metal fed as powder or wire with a laser, electron beam or arc (wire-arc additive manufacturing).
  3. Stereolithography cures a liquid resin, and selective laser sintering fuses a powder bed: neither uses wire.

Answer: (B) and (D).

Where this shows up in industry

Wire-fed DED builds large metal parts fast and cheaply: welding wire costs far less than fine metal powder. Aerospace and shipbuilding firms use wire-arc AM for big titanium and steel near-net shapes that are then machined.

GATE 2022 · ME Set-2 · Q.21MCQ · 1 markAdditive manufacturing

Match FDM, laminated object manufacturing and SLS with their input materials

Match the additive manufacturing technique in Column I with its corresponding input material in Column II.
Additive manufacturing technique (Column I)Input material (Column II)
P. Fused deposition modelling1. Photo sensitive liquid resin
Q. Laminated object manufacturing2. Heat fusible powder
R. Selective laser sintering3. Filament of polymer
4. Sheet of thermoplastic or green compacted metal sheet
  1. (A)P-3, Q-4, R-2
  2. (B)P-1, Q-2, R-4
  3. (C)P-2, Q-3, R-1
  4. (D)P-4, Q-1, R-4

Answer: (A) Official key: A

  1. FDM extrudes a polymer filament → 3.
  2. Laminated object manufacturing cuts and bonds sheets layer by layer → 4.
  3. Selective laser sintering fuses a heat-fusible powder bed → 2.

P-3, Q-4, R-2: option (A). Liquid resin (1) belongs to stereolithography, which is not in Column I.

Where this shows up in industry

SLS in nylon (PA12) is a common route for small batches of functional plastic parts such as ducts, brackets and housings, because the loose powder supports the part and no support structures are needed.

GATE 2025 · ME · Q.40MCQ · 2 marksAdditive manufacturing

Match SLA, FDM, LOM and LENS with their layer technique and material

In relation to additive manufacturing, match the following
ProcessLayer creation techniqueMaterial
P. Stereolithography1. Injection of powder streamI. Paper
Q. Fused deposition modeling2. Extrusion of melted polymerII. Epoxy
R. Laminated object manufacturing3. Liquid layer curingIII. Titanium
S. Laser-engineered net shaping4. Sheet material depositionIV. Acrylonitrile butadiene styrene (ABS)
  1. (A)P-3-III, Q-1-IV, R-4-I, S-2-II
  2. (B)P-3-II, Q-2-IV, R-4-I, S-1-III
  3. (C)P-4-III, Q-2-IV, R-1-II, S-3-I
  4. (D)P-3-II, Q-2-IV, R-1-I, S-4-III

Answer: (B) Official key: B

  1. Stereolithography cures a liquid photopolymer layer by layer: 3, epoxy resin (II).
  2. FDM extrudes melted polymer: 2, ABS (IV).
  3. Laminated object manufacturing stacks and cuts sheets: 4, paper (I).
  4. Laser-engineered net shaping (a DED process) injects a powder stream into a laser melt pool: 1, titanium (III).

P-3-II, Q-2-IV, R-4-I, S-1-III: option (B). A quick elimination: only (B) and (D) pair FDM with extrusion and SLA with epoxy, and (D) gives LOM the powder stream.

Where this shows up in industry

LENS-type powder-fed DED is used to repair worn turbine blade tips and to add features to existing metal parts, something powder-bed processes cannot do because they build only from a flat plate.

GATE 2026 · ME · Q.31MCQ · 1 markAdditive manufacturing

Which is NOT an STL file error: staircase effect, missing facet, non-manifold topology or degenerate facets?

Which one of the following options is NOT an error associated with STereoLithography (STL) file in additive manufacturing?
  1. (A)Staircase effect
  2. (B)Missing facet
  3. (C)Non-manifold topology conditions
  4. (D)Degenerate facets

Answer: (A) Official key: A

  1. An STL file approximates the surface with triangles. Missing facets (holes in the mesh), non-manifold topology (edges shared by more than two triangles, or triangles touching only at a point) and degenerate facets (triangles with zero area) are all defects of that triangle mesh.
  2. The staircase effect is the stepped surface left by building in finite layers. It comes from slicing and layer thickness, not from the STL file: option (A).
Where this shows up in industry

Every print job starts with an STL check: build-preparation software repairs holes, flipped normals and non-manifold edges before slicing. The staircase effect is reduced instead by thinner layers, adaptive slicing or a better build orientation.

From GATE prep to a manufacturing and design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.