GATE Mechanical: Engineering Mechanics, previous-year questions solved

Every engineering mechanics question from the last four GATE Mechanical papers that has an official key and is not already on another of our subject pages: trusses and frames (method of sections, zero-force members, a slotted link), support layouts under a couple, a three-hinged arch, friction on rods, ropes and an incline, and rigid-body dynamics from an impact on a pivoted rod to a gyroscope. Each answer is worked step by step, checked against the official key, and followed by where the idea shows up in engineering practice.

Questions from official GATE ME papers (IIT Kharagpur 2022, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 15 questions

GATE 2022 · ME Set-1 · Q.49NAT · 2 marksStatics: trusses, frames and supports

Pin-jointed structure with 2 kN and 4 kN loads: what is the force in member CI?

A structure, along with the loads applied on it, is shown in the figure. Self-weight of all the members is negligible and all the pin joints are friction-less. AE is a single member that contains pin C. Likewise, BE is a single member that contains pin D. Members GI and FH are overlapping rigid members. The magnitude of the force carried by member CI is ________ kN (in integer).
Pin-jointed structure: members AE (through pin C) and BE (through pin D) from wall pins A and B 3 m apart, top chord C-I-H 1.5 m above the bottom chord B-D-E-F-G, diagonals IE, IF, HF and GI, 2 kN to the right at H and 4 kN down at G; bottom spacings 2, 2, 3, 3 m, top spacings 3.5 and 3 mABCDEIHFG2 kN4 kN3.5 m3 m2 m2 m3 m3 m3 m

Answer: 18 kN Official key: 18 to 18

  1. Find the height of the top chord first. C lies on AE, which runs from A (3 m above B) to E (4 m from B). At C, 2 m from the wall, AE is at m. So C, I and H are 1.5 m above the bottom chord.
  2. Cut through CI, IE and EF and keep the part to the right. Two of the three cut members, IE and EF, pass through E, so take moments about E and only CI is left.
  3. About E: the 2 kN at H acts 1.5 m above E, giving ; the 4 kN at G acts 6 m to the right of E, giving , both clockwise. CI acts along the top chord, 1.5 m above E: , so (tension).

The right-hand panel I-H-G-F has both diagonals (GI and FH), so it is internally redundant: statics alone cannot split the load between GI and FH. That does not matter for CI. Our check solved the joint equations with two different assumed forces in GI and got 18 kN in CI both times. Trap: using 3 m (the height of A) as the lever arm gives 9 kN.

Where this shows up in industry

The method of sections is how engineers check one chord of a roof truss, crane boom or truss bridge without solving every joint, and it is still the standard hand check on an FEA truss model. X-braced (redundant) panels like I-H-G-F are common in towers and bridges because they stay safe if one diagonal buckles or is damaged.

GATE 2025 · ME · Q.27MCQ · 1 markStatics: trusses, frames and supports

Truss with a 1000 N load at A: which member is a zero-force member?

A truss structure is loaded as shown in the figure below. Among the options given, which member in the truss is a zero-force member?
Truss with pin support C, roller D 1 m to its right, joint A 1 m above D, member CA at 45 degrees with joint B at its middle, BD perpendicular to CA, and a 1000 N horizontal force at AF = 1000 NABCD90°45°1 m1 m√2 m
  1. (A)BD
  2. (B)BC
  3. (C)BA
  4. (D)AD

Answer: (A) Official key: A

  1. Look at joint B. Members BC and BA both lie along CA, so they are collinear. The only other member at B is BD, and no load acts at B.
  2. Resolve forces at B perpendicular to CA: BC and BA have no component in that direction, so the force in BD must be zero. BD is a zero-force member, option (A).

Full solution by the method of joints (tension positive): , (compression), reactions up, . Under this load CD also carries nothing, but it is not among the options.

Where this shows up in industry

Zero-force members are not wasted steel. They brace long compression members against buckling and carry load when the loading changes, for example wind from the other side or a moving load on a bridge. FEA truss models often show them with near-zero force for one load case and real force for another.

GATE 2024 · ME · Q.27MCQ · 1 markStatics: trusses, frames and supports

Massless tetrahedron with loads at A along x and at B along y: where must the third load at O point?

A rigid massless tetrahedron is placed such that vertex O is at the origin and the other three vertices A, B, and C lie on the coordinate axes as shown in the figure. The body is acted on by three point loads, of which one is acting at A along -axis and another at point B along -axis. For the body to be in equilibrium, the third point load acting at point O must be
Tetrahedron OABC with O at the origin and A, B, C on the x, y and z axesxyzOABC
  1. (A)along -axis
  2. (B)in plane but not along or axis
  3. (C)in plane but not along or axis
  4. (D)in plane but not along or axis

Answer: (B) Official key: B

  1. The load at A acts along the -axis, the line OA, so its line passes through O. The load at B acts along the -axis, the line OB, so it also passes through O. The third load acts at O. All three lines meet at O, so the moment equation about O is satisfied automatically.
  2. Only force balance is left: , so .
  3. That vector has no component and, with both given loads non-zero, has both and components: in the plane but not along or , option (B).

Vertex C and the shape of the tetrahedron play no part; the answer follows from concurrency alone.

Where this shows up in industry

Space frames, lattice towers and transmission pylons are designed on exactly this idea: members meet at nodes, loads go into the nodes, and every node is checked with force balance only. When the load lines do not meet at the node, the eccentricity creates bending, which designers try to avoid by detailing.

GATE 2024 · ME · Q.58NAT · 2 marksStatics: trusses, frames and supports

Three-hinged semicircular arch, P = 100 kN and Q = 50 kN: what is the horizontal reaction at B?

A three-hinge arch ABC in the form of a semi-circle is shown in the figure. The arch is in static equilibrium under vertical loads of kN and kN. Neglect friction at all the hinges. The magnitude of the horizontal reaction at B is ______ kN (rounded off to 1 decimal place).
Three-hinged semicircular arch of radius 6 m with supports A and C and crown hinge B; vertical loads P at 3 m left of B and Q at 3 m right of BACBPQ3 m3 m6 m6 m6 m

Answer: 37.5 kN Official key: 37.0 to 38.0

  1. Whole arch, moments about A (span 12 m, P at 3 m and Q at 9 m from A): , so and .
  2. The crown hinge B carries no moment. Take the right half BC and sum moments about B; C is 6 m right of and 6 m below B, Q is 3 m right of B: .
  3. . The only horizontal forces on BC are at C and the hinge force at B, so the horizontal reaction at B is 37.5 kN. The left half gives the same: .

Traps: the vertical reactions (87.5 and 62.5 kN) are not what is asked. The vertical force at B is kN, so the total hinge force is kN, outside the key: the question asks only for the horizontal part.

Where this shows up in industry

Three-hinged arches and portal frames are used for bridges, hangars and sports halls. The crown hinge makes the structure statically determinate, so temperature changes and small support settlements do not create extra stress. The price is the horizontal thrust at the supports, which foundations or a tie rod must take.

GATE 2022 · ME Set-1 · Q.50NAT · 2 marksFriction

Two rods of 5 m and 12 m pinned at R, slip impends at both feet at 90°: what is μQ/μP?

Two rigid massless rods PR and RQ are joined at frictionless pin-joint R and are resting on ground at P and Q, respectively, as shown in the figure. A vertical force F acts on the pin R as shown. When the included angle , the rods remain in static equilibrium due to Coulomb friction between the rods and ground at locations P and Q. At , impending slip occurs simultaneously at points P and Q. Then the ratio of the coefficient of friction at Q to that at P () is _________ (round off to two decimal places).
Two rods PR (5 m) and RQ (12 m) pinned at R, resting on the ground at P and Q, included angle theta at R, vertical force F down on RFRPQ5 m12 mθ

Answer: 5.76 Official key: 5.70 to 5.80

  1. The rods are massless and loaded only at their ends, so each is a two-force member: the ground pushes on it along the rod. At the foot, the horizontal part of that force is friction and the vertical part is the normal force.
  2. At impending slip , which is the cotangent of the rod's angle with the ground.
  3. At the triangle PRQ is right-angled at R, so m. PR rises at an angle whose cosine is (tangent ), so . RQ rises at an angle with tangent , so .
  4. 5.76.

F does not appear: it scales both forces equally. Traps: the inverse ratio is ; the ratio of the rod lengths is .

Where this shows up in industry

Stepladders and A-frames work the same way: the flatter leg pushes outward harder relative to its normal force and slips first, which is why stepladders have a spreader brace and rubber feet. The same two-force-member check is used for props, struts and toggle clamps.

GATE 2022 · ME Set-2 · Q.30NAT · 1 markFriction

Rope over a fixed pulley: 200 N lifts 5 discs; how many discs on the other side stop them sliding down?

A rope with two mass-less platforms at its two ends passes over a fixed pulley as shown in the figure. Discs with narrow slots and having equal weight of 20 N each can be placed on the platforms. The number of discs placed on the left side platform is and that on the right side platform is .
It is found that for and , a force N (refer to part (i) of the figure) is just sufficient to initiate upward motion of the left side platform. If the force is removed then the minimum value of (refer to part (ii) of the figure) required to prevent downward motion of the left side platform is______ (in integer).
A rope over a fixed (non-rotating) pulley carries a massless platform at each end. (i) n discs on the left platform and a force F pulling the right end down. (ii) n discs on the left platform and m discs on the rightndiscsFndiscsmdiscs(i)(ii)fixed pulleyg

Answer: 3 Official key: 3 to 3

  1. The pulley is fixed (it does not turn), so the rope slides over it and friction acts along the half turn of contact. The tensions on the two sides obey the capstan (belt friction) relation with .
  2. Part (i): the left platform weighs N and 200 N just lifts it, so ().
  3. Part (ii): now the left side (100 N) tends to go down and the right side is the slack side, holding N. No slip while , so and the smallest whole number is . With the ratio would be and the left side slides down.

Traps: a frictionless pulley would need (equal weights). is what it takes to lift the left platform, not to hold it.

Where this shows up in industry

The capstan equation sizes belt drives ( sets the most power a flat or V-belt can carry), band brakes, and the turns of rope on a winch drum or a ship's bollard. A few turns of rope round a bollard let one person hold a load many times their pull, because the ratio grows exponentially with wrap angle.

GATE 2026 · ME · Q.48NAT · 2 marksFriction

50 kg block on a 30° incline, μ = 0.3, moving pulley: what hanging mass starts it moving up?

A block of 50 kg mass is on an inclined plane. The block is connected to another hanging mass M by an inextensible massless string through two massless pulleys as shown in the figure below. The coefficient of static friction between the block and the inclined plane is 0.3. Neglecting pulley friction, the minimum value of M required to start the upward motion of the block is ________ kg (rounded off to 1 decimal place).
A 50 kg block on a 30 degree incline; a small pulley fixed to the block, a large fixed pulley at the top of the incline; the string runs from the large pulley's axle round the small pulley, back over the large pulley and down to a hanging mass M50 kgM30°

Answer: 19.0 kg Official key: 18.5 to 19.5

  1. Read the figure: the small pulley is fixed to the block, and the string runs from the axle of the big pulley, round the small pulley and back over the big pulley to M. Two string segments pull the block up the slope, each with tension .
  2. For upward motion to start, friction acts down the slope at its full value: .
  3. 19.0 kg. cancels.

Traps: counting one string segment gives 38.0 kg; leaving out friction gives 12.5 kg; putting friction up the slope (that is the condition for the block to start sliding down) gives 6.0 kg. All are outside the key.

Where this shows up in industry

Movable pulleys trade distance for force: a 2:1 arrangement halves the pull and doubles the rope travel. Chain hoists, crane hook blocks and many traction lifts (2:1 roping) use it, and the friction term is why conveyor and winch drives are sized for breakaway, not just for the slope.

GATE 2022 · ME Set-1 · Q.31NAT · 1 markRigid-body dynamics

0.001 kg mass at 200 cm/s sticks to a pivoted rod 10 cm from O: what is the rod's angular velocity?

The plane of the figure represents a horizontal plane. A thin rigid rod at rest is pivoted without friction about a fixed vertical axis passing through O. Its mass moment of inertia is equal to 0.1 kg·cm2 about O. A point mass of 0.001 kg hits it normally at 200 cm/s at the location shown, and sticks to it. Immediately after the impact, the angular velocity of the rod is ___________ rad/s (in integer).
Top view of a thin rod pivoted at O; a point mass moving at 200 cm/s strikes it at right angles 10 cm from OO10 cm200 cm/s

Answer: 10 rad/s Official key: 10 to 10

  1. During the impact the pivot exerts a large force on the rod, so linear momentum is not conserved. The pivot force passes through O, so angular momentum about O is.
  2. Before: only the point mass, .
  3. After: rod and mass turn together, .
  4. 10 rad/s. Working in cm throughout is fine because the units cancel.

Trap: forgetting that the stuck mass also adds to the moment of inertia gives rad/s.

Where this shows up in industry

The ballistic pendulum, which measures projectile speed, is this calculation in reverse. The same angular-momentum balance sizes the shock on a pivot when a tool or arm hits a hard stop, and it is the basis of impact checks on rotating machinery guards.

GATE 2022 · ME Set-1 · Q.32NAT · 1 markRigid-body dynamics

Annular disc with r² = R²/2 hung on a knife edge: find β in T = βπ√(R/g)

A rigid uniform annular disc is pivoted on a knife edge A in a uniform gravitational field as shown, such that it can execute small amplitude simple harmonic motion in the plane of the figure without slip at the pivot point. The inner radius and outer radius are such that , and the acceleration due to gravity is . If the time period of small amplitude simple harmonic motion is given by , where is the ratio of circumference to diameter of a circle, then ______ (round off to 2 decimal places).
Annular disc with inner radius r and outer radius R hanging on a knife edge A at the top of its inner rim; G is the centre; gravity g downwardAGrRg

Answer: 2.66 Official key: 2.62 to 2.70

  1. This is a compound pendulum: , where is the distance from the pivot to the centre of mass. The knife edge touches the inner rim, so .
  2. Moment of inertia of an annulus about its centre (axis normal to the disc): .
  3. Parallel axis to the pivot: .
  4. , so 2.66.

Traps: leaving out the parallel-axis term gives ; treating it as a simple pendulum of length gives 1.68.

Where this shows up in industry

Swinging a part as a compound pendulum and timing it is a standard way to measure its moment of inertia: connecting rods, flywheels, wheels and whole vehicles (on large pendulum rigs) are tested like this. The measured inertia goes straight into multibody dynamics and NVH models.

GATE 2022 · ME Set-1 · Q.51NAT · 2 marksRigid-body dynamics

Disc spinning at 5 rad/s placed on the ground: what is its speed when it starts rolling?

A cylindrical disc of mass kg and radius m was spinning at rad/s when it was placed on a flat horizontal surface and released (refer to the figure). Gravity acts vertically downwards as shown in the figure. The coefficient of friction between the disc and the surface is finite and positive. Disregarding any other dissipation except that due to friction between the disc and the surface, the horizontal velocity of the center of the disc, when it starts rolling without slipping, will be _________ m/s (round off to 2 decimal places).
Disc of mass m and radius r spinning at omega, placed on a flat horizontal surface; gravity g acts downwardrmωg

Answer: 0.25 m/s Official key: 0.24 to 0.26

  1. While the disc skids, friction speeds the centre up and slows the spin. Friction acts at the contact point, and weight and normal force cancel, so angular momentum about the contact point (a fixed point on the ground line) is conserved.
  2. Start: the centre is at rest, so only the spin counts: .
  3. Rolling: with , which is .
  4. , so 0.25 m/s.

The friction coefficient only sets how long the skid lasts; our check integrated the motion for , and and got 0.25 m/s each time. Traps: m/s ignores the skid; using a solid sphere () or a ring () uses the wrong inertia.

Where this shows up in industry

A bowling ball skids, hooks and then rolls for exactly this reason. Vehicle engineers meet the same skid-to-grip phase in wheel spin at launch and in ABS and traction control, where the controller keeps the tyre near the slip that gives the most friction.

GATE 2022 · ME Set-2 · Q.37MCQ · 2 marksRigid-body dynamics

1 kg block 0.4 m × 0.3 m on a pin and roller: what minimum impulse topples it?

A rigid homogeneous uniform block of mass 1 kg, height m and width m is pinned at one corner and placed upright in a uniform gravitational field ( m/s2), supported by a roller in the configuration shown in the figure. A short duration (impulsive) force , producing an impulse , is applied at a height of m from the bottom as shown. Assume all joints to be frictionless. The minimum value of required to topple the block is
Upright block of width b and height h pinned at its bottom corner on the far side and resting on a roller on an incline at the near corner; an impulsive horizontal force F acts at height d from the bottombhdFg
  1. (A)0.953 Ns
  2. (B)1.403 Ns
  3. (C)0.814 Ns
  4. (D)1.172 Ns

Answer: (A) Official key: A

  1. The push makes the block turn about the pin O at the far bottom corner; the roller can only push, so the near corner simply lifts off.
  2. Angular impulse about O (the pin's impulsive force passes through O): , with .
  3. To topple, G must rise until it is directly above O. G starts m high and ends at the half-diagonal, m: a rise of 0.05 m.
  4. Energy: , so .
  5. 0.953 N s, option (A).

Our check integrated the rotation: an impulse 0.2% above this value tips the block over, 0.2% below it falls back.

Where this shows up in industry

Tip-over checks for tall cabinets, machine tools, transformers and stacked loads use the same rule: the centre of gravity must not pass over the pivot edge. Seismic anchoring of equipment, forklift stability tests and shipping-shock specifications all come down to an impulse or acceleration compared with this energy barrier.

GATE 2024 · ME · Q.24MCQ · 1 markRigid-body dynamics

Ram on two parallel 7 m ropes must hit at 5 m/s: from what angle should it be released?

A ram in the form of a rectangular body of size m and m is suspended by two parallel ropes of lengths 7 m. Assume the center-of-mass of the body is at its geometric center and m/s2. For striking the object P with a horizontal velocity of 5 m/s, what is the angle with the vertical from which the ram should be released from rest?
Rectangular ram of length l and depth b hung from two parallel 7 m ropes, pulled back to angle theta from the vertical; dashed outline shows it hanging straight down, just touching object PramPθθ7 m7 mlb
  1. (A)67.1°
  2. (B)40.2°
  3. (C)35.1°
  4. (D)79.5°

Answer: (C) Official key: C

  1. Two equal parallel ropes form a parallelogram, so the ram does not rotate: it translates, and every point, including the centre of mass, moves on a circle of radius 7 m.
  2. Energy from release to the lowest point: .
  3. , so 35.1°, option (C).

The size of the ram ( and ) is a distractor: because it only translates, it has no rotational energy, and its shape does not enter.

Where this shows up in industry

Pendulum impactors are used to test vehicle bumpers, crash barriers and packaging, and the impact speed is set exactly like this, by the release height. Parallel-arm (parallelogram) linkages that keep a body level while it moves are common too: monitor arms, drafting machines and parallelogram lifting platforms.

GATE 2022 · ME Set-2 · Q.17MCQ · 1 markRigid-body dynamics

Spinning disc on a shaft hung by two strings: one string is cut; which way does the shaft turn?

A massive uniform rigid circular disc is mounted on a frictionless bearing at the end E of a massive uniform rigid shaft AE which is suspended horizontally in a uniform gravitational field by two identical light inextensible strings AB and CD as shown, where G is the center of mass of the shaft-disc assembly and is the acceleration due to gravity. The disc is then given a rapid spin about its axis in the positive x-axis direction as shown, while the shaft remains at rest. The direction of rotation is defined by using the right-hand thumb rule. If the string AB is suddenly cut, assuming negligible energy dissipation, the shaft AE will
Horizontal shaft AE hung from strings AB and CD of length L; a disc at end E spins at omega about the positive x axis; G, the centre of mass of the assembly, lies between A and C; axes x along the shaft, z upLLBDAGCEωxzyg
  1. (A)rotate slowly (compared to ) about the negative z-axis direction
  2. (B)rotate slowly (compared to ) about the positive z-axis direction
  3. (C)rotate slowly (compared to ) about the positive y-axis direction
  4. (D)rotate slowly (compared to ) about the negative y-axis direction

Answer: (A) Official key: A

  1. After AB is cut, the assembly hangs from string CD at C. G lies between A and C, a distance on the side of C, so the weight gives a torque about C: , along .
  2. The spinning disc carries a large angular momentum along . The torque changes it: , so the tip of moves towards .
  3. swinging from towards in the horizontal plane is a rotation about the axis. The shaft precesses slowly (rate , small because is large) about the negative z-axis, option (A).

Trap: without the spin the A end would simply drop, a rotation about (option D). The spin turns that tendency into a sideways precession.

Where this shows up in industry

Gyroscopic couples load the bearings of ship turbines, aircraft propellers and jet engine rotors whenever the vehicle pitches or turns, and they are checked in rotor design. Spacecraft such as the ISS steer with control moment gyroscopes, and motorcycle counter-steering relies on the same effect.

From GATE prep to a CAE career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.