GATE Civil: Engineering Mechanics and Solid Mechanics (SFD and BMD, stresses, torsion, Mohr's circle, buckling), previous-year questions solved, part 3

Part 3 of 3 of the Solid Mechanics hub: 14 more official GATE CE questions on bending, shear stress, shear centre and torsion and stress transformation, thin shells, combined stress and buckling, each solved step by step and checked against the official answer key. Part 1 covers engineering mechanics: forces, friction, centroids and vibration, shear force and bending moment in determinate beams and stress, strain, axial and thermal members.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 14 of 36 questions on this page

GATE 2022 · CE1 · Q.16MCQ · 1 markBending, shear stress, shear centre and torsion

Where is the shear centre of a thin-walled T-section with an unequal flange?

Consider the cross-section of a beam made up of thin uniform elements having thickness () shown in the figure. The (, ) coordinates of the points along the center-line of the cross-section are given in the figure.

The coordinates of the shear center of this cross-section are:

Thin-walled T cross-section of uniform thickness t. Flange centre-line from H at (minus 2a, 3a) to K at (a, 3a), extending 2a to the left and a to the right of the y-axis; web centre-line along the y-axis from J at (0, 0) up to the flange, height 3ayx2aa3aH(−2a, 3a)K (a, 3a)J (0, 0)tt
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The shear centre is the point through which a transverse load must pass for the beam to bend without twisting. It is where the resultant of the shear flow acts.
  2. In a thin wall the shear flow runs along the centre-line of each element, so the shear force carried by a straight element acts along that element's line.
  3. Here there are only two straight elements: the flange HK on and the web on . Both lines pass through the junction .
  4. For any direction of shear, both element forces pass through the junction, so their moment about it is zero. The shear centre is the junction: (A) .

Trap: the flange is unequal (2 left, right), which tempts a shift to the left. That moves the centroid, to , not the shear centre. The same rule puts the shear centre of an angle at the corner where its legs meet.

Where this shows up in industry

Channels, angles and tees used as purlins, lintels or side rails twist when the load misses the shear centre. That is why sheeting loads on a channel purlin are kept close to the web, and why single angles in roof trusses are checked for the eccentricity of their connection.

GATE 2023 · CE2 · Q.14MCQ · 1 markBending, shear stress, shear centre and torsion

Angle of twist and torsional strain energy of a 5 m cantilever shaft with a 100 kN.m end torque

A circular solid shaft of span m is fixed at one end and free at the other end. A torque kN.m is applied at the free end. The shear modulus and polar moment of inertia of the section are denoted as and , respectively. The torsional rigidity is 50,000 kN.m2/rad. The following are reported for this shaft:

Statement i) The rotation at the free end is 0.01 rad
Statement ii) The torsional strain energy is 1.0 kN.m

With reference to the above statements, which of the following is true?

  1. (A)Both the statements are correct
  2. (B)Statement i) is correct, but Statement ii) is wrong
  3. (C)Statement i) is wrong, but Statement ii) is correct
  4. (D)Both the statements are wrong

Answer: (B) Statement i) is correct, but Statement ii) is wrong Official key: B

  1. Angle of twist of a uniform shaft carrying a torque at its free end: .
  2. rad, so Statement i) is correct.
  3. The torque grows from zero to as the shaft twists, so the stored energy is the triangle under the linear torque-twist line: .
  4. kN.m, not 1.0 kN.m, so Statement ii) is wrong.
  5. Answer: (B) Statement i) is correct, but Statement ii) is wrong.

Trap: kN.m makes Statement ii) look right and leads to (A). That is the work of a torque already at full value before the twist starts; a gradually applied torque stores half of it, the same factor as for an axially loaded bar.

Where this shows up in industry

Drive shafts, torsion bars and the spandrel beams that carry slab edges are checked for twist this way. Designers limit the angle of twist per metre as well as the shear stress, because too much twist misaligns couplings and cracks finishes.

GATE 2024 · CE1 · Q.40MCQ · 2 marksBending, shear stress, shear centre and torsion

Stepped shaft fixed at both ends with a torque at Q: length ratio L1/L2 when TP/TR = 4 and J1/J2 = 2

A homogeneous shaft PQR with fixed supports at both ends is subjected to a torsional moment at point Q, as shown in the figure. The polar moments of inertia of the portions PQ and QR of the shaft with circular cross-sections are and , respectively. The torsional moment reactions at the supports P and R are and , respectively.

(Figure NOT to scale)

If and , the ratio of the lengths is

Stepped shaft fixed at P and R with a torque T at QTJ1J2PQRL1L2Redrawn, not to scale
  1. (A)0.50
  2. (B)0.25
  3. (C)4.00
  4. (D)2.00

Answer: (A) 0.50 Official key: A

  1. Equilibrium gives only : one equation, two unknowns, so the shaft is statically indeterminate and needs a compatibility condition.
  2. Both ends are fixed, so Q turns through one angle whichever part you follow: the twist of PQ equals the twist of QR, .
  3. Rearranging: .
  4. Answer: (A) 0.50.

Trap: each part acts as a torsional spring of stiffness , and the torque splits in proportion to stiffness. Putting the ratio the wrong way up, , gives 2.00, option (D); ignoring gives , option (B).

Where this shows up in industry

Stepped shafts fixed at both ends turn up in gear trains and in torsion bars between two stiff frames; the stiffer, shorter segment attracts most of the torque, so that segment is the one checked for shear stress.

GATE 2024 · CE2 · Q.18MCQ · 1 markBending, shear stress, shear centre and torsion

Where is the shear centre of an I-section whose flanges project 6 cm on one side of the web and 3 cm on the other?

For a thin-walled section shown in the figure, points P, Q, and R are located on the major bending axis of the section. Point Q is located on the web whereas point S is located at the intersection of the web and the top flange of the section.

Qualitatively, the shear center of the section lies at

I-section with flanges projecting 6 cm left and 3 cm right of the web6 cm3 cmXXPQRS6 cm3 cm
  1. (A)P
  2. (B)Q
  3. (C)R
  4. (D)S

Answer: (C) R Official key: C

  1. The section is symmetric about , so the shear centre lies on that axis: (D) S is out.
  2. Under a vertical shear , shear flow in each flange outstand grows linearly from its free tip to the web. The horizontal force in an outstand of width is (with the distance between flange centrelines).
  3. In the top flange the 6 cm and 3 cm outstands carry opposite forces, so the net is proportional to , in the direction of the wider outstand's flow. The bottom flange carries the same net force the other way: a couple, exactly as in a channel whose flanges point left.
  4. To cancel that couple the load must act on the side away from the wider outstand: to the right of the web.
  5. Answer: (C) R.

Trap: picking (B) Q, the web, which is right only when both outstands are equal; or (A) P, assuming the shear centre moves towards the larger flange area. Like a channel, the shear centre falls on the side opposite the bigger outstands.

Where this shows up in industry

Cold-formed purlins and channel lintels twist if loads go through the web instead of the shear centre, so designers add sag rods, place the open side correctly or check torsion; steel tables list the shear centre offset of each channel.

GATE 2026 · CE1 · Q.14MCQ · 1 markBending, shear stress, shear centre and torsion

Where is the shear centre of a thin angle section? Pick the figure with the dot in the right place

Black dot shown in the figure qualitatively represents the shear centre of the angle section. The option which represents the position of the shear centre is:

  1. (A)Option A: angle section with the shear centre dot outside the angle, to the right of the vertical leg
  2. (B)Option B: angle section with the shear centre dot near the free end of the horizontal leg
  3. (C)Option C: angle section with the shear centre dot inside the angle, away from both legs
  4. (D)Option D: angle section with the shear centre dot at the corner where the two legs meet

Answer: (D) Dot at the corner where the two legs meet Official key: D

  1. The shear centre is the point through which a transverse load must pass for the section to bend without twisting; it is the point the resultant of the shear flows passes through.
  2. In a thin angle the shear flow in each leg runs along the leg, so the shear force carried by each leg acts along that leg's centreline.
  3. Both leg forces therefore pass through the point where the two centrelines meet, the corner of the angle. Their moment about that point is zero, so whatever the load direction, that point is the shear centre.
  4. Answer (D).

Trap: (C) marks roughly the centroid, which for an angle lies inside the angle, off both legs. The centroid and the shear centre coincide only for doubly symmetric sections. (A) is where a channel's shear centre sits, outside the web on the side away from the flanges.

Where this shows up in industry

Angles used as purlins, lintels and bracing are usually loaded through a leg rather than through the corner, so they twist as they bend. Designers allow for this or pair two angles back to back, which makes the section symmetric about the load plane.

GATE 2022 · CE1 · Q.13MCQ · 1 markStress transformation, thin shells, combined stress and buckling

What is the maximum shear stress in a thin cylinder when the hoop stress is 30 MPa?

The hoop stress at a point on the surface of a thin cylindrical pressure vessel is computed to be 30.0 MPa. The value of maximum shear stress at this point is

  1. (A)7.5 MPa
  2. (B)15.0 MPa
  3. (C)30.0 MPa
  4. (D)22.5 MPa

Answer: (A) 7.5 MPa or (B) 15.0 MPa: both are accepted Official key: A OR B

  1. In a thin cylinder the hoop stress is twice the longitudinal stress: MPa, so MPa. On the outer surface the radial stress is zero.
  2. In the plane of the shell wall the maximum shear is the radius of Mohr's circle of and : MPa, option (A).
  3. Including the third principal stress, , the absolute maximum shear is MPa, option (B). It acts on planes at 45° through the wall thickness.
  4. The question does not say which maximum it means, so the official key accepts both: (A) 7.5 MPa or (B) 15.0 MPa.

Trap: (C) is the hoop stress itself, and (D) MPa is the centre of Mohr's circle, an average normal stress, not a shear stress.

Where this shows up in industry

Thin-shell formulas size water mains, penstocks and gas cylinders. The hoop stress is twice the longitudinal stress, which is why a pressurised pipe splits along its length, and a Tresca yield check uses the absolute maximum shear, not the in-plane value.

GATE 2023 · CE1 · Q.53NAT · 2 marksStress transformation, thin shells, combined stress and buckling

Maximum principal stress from an element with horizontal faces and 45 degree inclined faces

The infinitesimal element shown in the figure (not to scale) represents the state of stress at a point in a body. What is the magnitude of the maximum principal stress (in N/mm2, in integer) at the point?

Stress element shaped as a parallelogram: top and bottom faces horizontal, side faces inclined at 45 degrees; on the horizontal faces a tensile normal stress of 6 and a shear stress of 3 N/mm2 (to the right on the top face); on the inclined faces a tensile normal stress of 5 and a shear stress of 4 N/mm2 (up the face on the right side)6 N/mm²3 N/mm²6 N/mm²3 N/mm²5 N/mm²4 N/mm²5 N/mm²4 N/mm²45°

Answer: Official key: 7 to 7

  1. Take horizontal and vertical. The horizontal faces give and directly; is unknown because no face is vertical.
  2. On the right inclined face the outward normal is . Its traction is plus 4 along the face towards the upper left, so .
  3. Cauchy: . The second gives , a check; the first gives .
  4. Mohr circle: centre , radius .
  5. 7 N/mm2 (and ).

Trap: reading the 5 on the inclined face as gives , not an integer and not the answer. Stresses on a 45 degree face must be converted back to the and faces first.

Where this shows up in industry

Strain-gauge rosettes on bridges and pressure vessels are read at 0, 45 and 90 degrees for exactly this reason: the inclined reading is what lets the engineer recover the missing component and then the principal stresses that govern yielding or cracking.

GATE 2023 · CE2 · Q.39MCQ · 2 marksStress transformation, thin shells, combined stress and buckling

Principal stresses from 120 MPa normal and 70 MPa shear stress on the inclined face of a 3-4-5 wedge

In a two-dimensional stress analysis, the state of stress at a point is shown in the figure. The values of length of PQ, QR, and RP are 4, 3, and 5 units, respectively. The principal stresses are ______. (round off to one decimal place)

Triangular element PQR: PQ vertical (4 units), QR horizontal (3 units), hypotenuse RP (5 units). Face PQ carries sigma x pulling in the minus x direction, face QR carries sigma y pulling downward, and face RP carries a normal tensile stress of 120 MPa and a shear stress of 70 MPa acting along RP towards Pyxσxσyσ = 120 MPaτ = 70 MPaPQR435
  1. (A) MPa, MPa
  2. (B) MPa, MPa
  3. (C) MPa, MPa
  4. (D) MPa, MPa

Answer: (C) MPa, MPa Official key: C

  1. Faces PQ (vertical) and QR (horizontal) carry only normal stresses, no shear, so they are principal planes and , are the principal stresses.
  2. Take unit thickness: face areas PQ = 4, QR = 3, RP = 5. The outward normal of RP is ; the 70 MPa shear acts along RP towards P, direction .
  3. Force on RP: along and along .
  4. balance: , so MPa. balance: , so MPa: (C).
  5. Check with the transformation equations on RP: MPa and MPa.

Trap: taking the shear on RP the other way (towards R) gives and MPa, which option (A) lists with the labels swapped. Balancing stresses instead of forces (ignoring the face lengths) fails too.

Where this shows up in industry

Strain gauge rosettes and finite element plots give stress components on arbitrary planes. Turning them into principal stresses is how engineers check welds, gusset plates and concrete, which cracks across the direction of the principal tensile stress.

GATE 2024 · CE1 · Q.14MCQ · 1 markStress transformation, thin shells, combined stress and buckling

Maximum shear stress at a point whose 3D stress tensor is diagonal: 10, 40 and 0 MPa

The three-dimensional state of stress at a point is given by

The maximum shear stress at the point is

  1. (A)20 MPa
  2. (B)15 MPa
  3. (C)5 MPa
  4. (D)25 MPa

Answer: (A) 20 MPa Official key: A

  1. The matrix is diagonal, so the x, y and z faces carry no shear: the three normal stresses are already the principal stresses, , and .
  2. In three dimensions the absolute maximum shear stress is the radius of the largest of the three Mohr's circles: .
  3. , on planes at to the y and z axes.
  4. Answer: (A) 20 MPa.

Trap: working only in the x-y plane gives , option (B). A zero principal stress is still a principal stress, and the biggest circle runs from 0 to 40 MPa. (D) adds the stresses instead of subtracting them.

Where this shows up in industry

Ductile steel checks use exactly this: the Tresca criterion limits (sigma1 - sigma3)/2, and a plate in biaxial tension with a free surface (sigma3 = 0) yields on an out-of-plane shear plane, not on the in-plane one.

GATE 2024 · CE1 · Q.38MCQ · 2 marksStress transformation, thin shells, combined stress and buckling

Match uniaxial tension, pure shear, uniaxial compression and biaxial compression to their Mohr's circles

Find the correct match between the plane stress states and the Mohr’s circles.

Plane stress states P to S and Mohr circles I to IV(P)1010(Q)10101010(R)1010(S)10101010(I)στ-10(II)στ-10(III)στ10(IV)στ-1010Redrawn, not to scale
  1. (A)(P)-(III); (Q)-(IV); (R)-(I); (S)-(II)
  2. (B)(P)-(III); (Q)-(II); (R)-(I); (S)-(IV)
  3. (C)(P)-(I); (Q)-(IV); (R)-(III); (S)-(II)
  4. (D)(P)-(I); (Q)-(II); (R)-(III); (S)-(IV)

Answer: (A) (P)-(III); (Q)-(IV); (R)-(I); (S)-(II) Official key: A

  1. For a plane stress state Mohr's circle has centre and radius .
  2. (P) tension 10 on the vertical faces: centre 5, radius 5, a circle from 0 to 10: (III).
  3. (Q) pure shear 10: centre 0, radius 10, a circle from to 10: (IV).
  4. (R) compression 10 on the horizontal faces: centre , radius 5, a circle from to 0: (I).
  5. (S) equal compression 10 both ways: centre , radius 0. Every plane carries and no shear, so the circle shrinks to a point: (II).
  6. Answer: (A) (P)-(III); (Q)-(IV); (R)-(I); (S)-(II).

Trap: arrows pointing away from a face are tension, arrows pushing into it are compression. Reading them the other way swaps P and R and gives (C). Options (B) and (D) give the point circle to pure shear, but a pure shear state always has a circle centred on the origin.

Where this shows up in industry

Mohr's circle is still how engineers read FE stress output: pure shear in a torsion member means principal planes at 45 degrees, which is why concrete in torsion cracks in spirals and brittle cast-iron shafts snap along a helix.

GATE 2024 · CE2 · Q.39MCQ · 2 marksStress transformation, thin shells, combined stress and buckling

Temperature rise that buckles a fixed-fixed steel bar with slenderness ratio 105 and effective length 0.5l

A homogeneous, prismatic, linearly elastic steel bar fixed at both the ends has a slenderness ratio () of 105, where is the bar length and is the radius of gyration. The coefficient of thermal expansion of steel is . Consider the effective length of the steel bar as and neglect the self-weight of the bar.

The differential increase in temperature (rounded off to the nearest integer) at which the bar buckles is

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The fixed ends stop the bar expanding, so a temperature rise creates an axial compressive stress .
  2. Euler buckling stress: with , so .
  3. Buckling when ; cancels.
  4. .
  5. Answer: (A) .

Trap: using the full length as the effective length gives , a quarter of the answer; the fixed-fixed effective length makes the bar four times stronger against buckling.

Where this shows up in industry

Continuous welded rail is the classic case: with no expansion joints a hot day builds compressive force, and railways set the stress-free laying temperature and ballast resistance so the track does not buckle sideways.

GATE 2025 · CE2 · Q.39MCQ · 2 marksStress transformation, thin shells, combined stress and buckling

Maximum compressive stress for the difference of two uniaxial stress states at 0 and 45 degrees

Let the state of stress at a point in a body be the difference of two plane states of stress shown in the figure. Consider all the possible planes perpendicular to the x-y plane and passing through that point. The magnitude of the maximum compressive stress on any such plane is , where k is equal to ______ (round off to one decimal place).

Two plane states of stress. State 1: uniaxial tension 3 sigma0 along x. State 2: uniaxial tension 3 sigma0 normal to the faces of an element turned 45 degrees, acting along the line from upper left to lower right3σ₀3σ₀xy3σ₀3σ₀45°xyState 1State 2Redrawn, not to scale
  1. (A)3.0
  2. (B)2.1
  3. (C)1.7
  4. (D)1.5

Answer: (B) 2.1 Official key: B

  1. State 1: , , .
  2. State 2 is a uniaxial along the line. With , , : and .
  3. Difference (1 minus 2): , , .
  4. Mohr's circle: centre , radius . Principal stresses .
  5. The largest compression on any plane normal to the x-y plane is , so : answer (B). Reading the arrows along the line instead only flips the sign of ; the radius is the same.

Trap: (D) 1.5 is alone, missing the shear. Adding the two states instead of subtracting gives principal stresses of and , both tensile.

Where this shows up in industry

Superposing load cases is how every structural program builds design combinations, and a compressive principal stress appearing out of two tensile cases is why codes check principal stresses, not only direct stresses, for example in the webs of prestressed girders.

GATE 2026 · CE1 · Q.13MCQ · 1 markStress transformation, thin shells, combined stress and buckling

Thin-walled spherical balloon under internal pressure: maximum tensile stress and shear stress in the wall

A thin-walled spherical gas balloon of radius and wall thickness () is subjected to an internal (gauge) pressure . The maximum tensile and shear stresses in the balloon wall are, respectively:

  1. (A)Zero and
  2. (B) and Zero
  3. (C) and
  4. (D) and Zero

Answer: (B) and Zero Official key: B

  1. Cut the sphere through its centre. The pressure on the half, , is held by the wall ring, , so .
  2. By symmetry every direction in the wall carries the same stress: , the maximum tensile stress.
  3. With equal in-plane principal stresses, Mohr's circle for the wall shrinks to a point: the in-plane shear stress on every plane normal to the wall.
  4. Answer (B).

Trap: bringing in the radial direction (stress close to zero at the outer surface) gives an out-of-plane shear , which is option (C). The official key is (B), so the question means the shear in the plane of the thin wall. Option (D) is the sphere formula with the radius put in place of the diameter.

Where this shows up in industry

Spherical pressure vessels such as the Horton spheres that store LPG at refineries are chosen because the membrane stress is pR/2t, half the hoop stress pR/t of a cylinder of the same radius, so the shell plate can be about half as thick.

GATE 2026 · CE2 · Q.17MCQ · 1 markStress transformation, thin shells, combined stress and buckling

Which of four stress elements, each with 40 units on its faces, represents a state of pure shear?

Which one of the following stress conditions represents the state of pure shear stress?

  1. (A)Option A: Element with 40 tension on the vertical faces, 40 compression on the horizontal faces and 40 shear on all four faces4040404040404040
  2. (B)Option B: Element with 40 tension on all four faces and 40 shear on all four faces4040404040404040
  3. (C)Option C: Element with 40 compression on all four faces and 40 shear on all four faces4040404040404040
  4. (D)Option D: Element with 40 tension on all four faces and no shear40404040

Answer: (A) Element with 40 tension on the vertical faces, 40 compression on the horizontal faces and 40 shear on all four faces Official key: A

  1. A state of pure shear is one where some pair of perpendicular planes carries shear only, no normal stress. On Mohr's circle that needs the centre at the origin: , i.e. .
  2. Centre , radius .
  3. (A): , , : , . Principal stresses at ; rotating from them gives planes with zero normal stress and shear : pure shear.
  4. (B): , : , . (C): : and . (D): , : every plane carries 40 tension and no shear.
  5. Answer (A).

Trap: (A), (B) and (C) all show shear on every face, so looking for shear arrows decides nothing. The test is the sum of the normal stresses, which is the same on every orientation and must be zero for pure shear.

Where this shows up in industry

A shaft in pure torsion is the textbook pure shear element: its principal stresses of equal tension and compression at 45 degrees are why a brittle cast iron shaft breaks along a 45-degree helix, while a ductile steel shaft shears off flat across the section.

From GATE prep to a structural design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.