GATE Civil: Steel Structures (welded and bolted connections, IS 800 beams, shape factor and plastic analysis), previous-year questions solved

Every steel structures question from the ten official GATE Civil papers of 2022-2026 (CE1 and CE2 each year): 13 questions (7 NAT, 6 MCQ) on welded and bolted connections, an IS 800 beam check and plastic analysis, each solved to IS 800:2007 and checked by a script against the official key. No paper asked a tension- or compression-member design sum. GATE 2027 drops plate girders and trusses and limits plastic analysis to beams and portal frames.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 13 questions

GATE 2022 · CE1 · Q.38MCQ · 2 marksBolted and welded connections

Balanced fillet weld lengths L1 and L2 to connect an ISA 100x100x10 angle to a gusset for full strength

A weld is used for joining an angle section ISA 100 mm × 100 mm × 10 mm to a gusset plate of thickness 15 mm to transmit a tensile load. The permissible stress in the angle is 150 MPa and the permissible shear stress on the section through the throat of the fillet weld is 108 MPa. The location of the centroid of the angle is represented by in the figure, where mm. The area of cross-section of the angle is 1903 mm2. Assuming the effective throat thickness of the weld to be 0.7 times the given weld size, the lengths and (rounded-off to the nearest integer) of the weld required to transmit a load equal to the full strength of the tension member are, respectively

Angle ISA 100 x 100 x 10 lapped on a 15 mm gusset plate. Elevation: weld L1 along the heel edge and shorter weld L2 along the toe edge, 100 mm apart. End view: 5 mm fillet welds at the heel and toe; centroid distance Cyy measured from the heel edgeL1L2100 mmCyy5 mm weld5 mm weld15 mm thick gusset plate
  1. (A)541 mm and 214 mm
  2. (B)214 mm and 541 mm
  3. (C)380 mm and 151 mm
  4. (D)151 mm and 380 mm

Answer: (A) 541 mm and 214 mm Official key: A

  1. Full strength of the angle: .
  2. Throat mm (IS 800:2007 Cl. 10.5.3.1, for 90 degree fusion faces), so one mm of weld carries .
  3. Total length: mm.
  4. Balance the welds so their resultant passes through the centroid (no eccentric moment): . The weld nearer the centroid (heel side, ) takes the larger share.
  5. mm and mm.
  6. Answer: (A) 541 mm and 214 mm

Trap: (B) swaps the two. The weld at the toe, 71.6 mm from the centroid, must be the shorter one; putting the longer weld there shifts the weld resultant away from the line of the load.

Where this shows up in industry

Balanced welds are standard for single-angle truss and bracing members in industrial sheds and towers; connection tools such as IDEA StatiCa or the Tekla Structures weld macros apportion heel and toe weld lengths in exactly this ratio before fabrication drawings are issued.

GATE 2023 · CE1 · Q.31NAT · 1 markBolted and welded connections

Safe load on a fillet-welded lap joint with two 75 mm side welds and a 50 mm end weld

Consider the fillet-welded lap joint shown in the figure (not to scale). The length of the weld shown is the effective length. The welded surfaces meet at right angle. The weld size is 8 mm, and the permissible stress in the weld is 120 MPa. What is the safe load P (in kN, rounded off to one decimal place) that can be transmitted by this welded joint? ________

Lap joint: a 50 mm wide plate laps 75 mm onto a wider plate and is fillet welded along both 75 mm side edges and across its 50 mm end; P pulls the two plates apart along the centre linePP75 mm50 mm

Answer: Official key: 134.0 to 136.0

  1. The figure shows three weld lines, all effective lengths: two side (longitudinal) fillets of 75 mm along the edges of the narrow plate and one end (transverse) fillet of 50 mm across its end: .
  2. The fusion faces meet at 90°, so the effective throat is (IS 800:2007 Cl. 10.5.3.2, Table 22, ): .
  3. In the working-stress method the weld fails in shear on the throat area, and side and end welds are treated alike, so .
  4. Safe load

Trap: counting only the two 75 mm side welds gives , and using the 8 mm size instead of the 5.6 mm throat gives ; both miss the key.

Where this shows up in industry

Bracing flats and tie plates lapped onto gussets are detailed exactly like this in Tekla shop drawings: the weld size, the effective length on each edge and an all-round end weld are specified, and the welding inspector checks the leg size with a fillet gauge because the throat (0.7 s) is what carries the load.

GATE 2023 · CE2 · Q.40MCQ · 2 marksBolted and welded connections

Minimum length of each side fillet weld to carry 275 kN in a lap joint as per IS 800 limit state

Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the figure. The thickness of each plate is 12 mm. The yield stress and the ultimate stress of steel under tension are 250 MPa and 410 MPa, respectively. The welding is done in the workshop (partial safety factor, ). As per the Limit State Method of IS 800: 2007, what is the minimum length (in mm, rounded off to the nearest higher multiple of 5 mm) required of each weld to transmit a factored force P equal to 275 kN?

Lap joint in plan: a 100 mm wide plate pulled up by P overlaps the end of a 150 mm wide plate pulled down by P; fillet welds run along both long edges of the 100 mm plate in the overlapPP100 mm150 mm
  1. (A)100
  2. (B)105
  3. (C)110
  4. (D)115

Answer: (B) 105 mm Official key: B

  1. Two side fillet welds, one along each edge of the 100 mm plate, share the factored force equally.
  2. Throat (IS 800 Cl. 10.5.3.2, Table 22): .
  3. Design strength of a shop fillet weld (Cl. 10.5.7.1.1): .
  4. Strength per mm of weld , so each weld needs .
  5. Next higher multiple of 5 mm: (B) 105 mm (effective length; on the drawing the overall length adds for the end craters, Cl. 10.5.4.1).

Trap: (A) 100 mm looks neat because it equals the plate width, but two 100 mm welds carry only . Using in place of also gives a wrong, much longer weld.

Where this shows up in industry

Shop-welded lap splices and tie connections in trusses are sized this way, with for shop welds and 1.50 for field welds (IS 800 Table 5); the fabricator's drawing then shows the 10 mm fillet symbol and the length on each side, plus end returns.

GATE 2025 · CE1 · Q.54NAT · 2 marksBolted and welded connections

Batten plate bolted with 6 bolts, longitudinal shear 70 kN and moment 10 kN.m: what bolt value is needed?

Consider the built-up column made of two I-sections as shown in the figure, with each batten plate bolted to a component I-section of the column through 6 black bolts. Each connection of the batten plate with the component section is to be designed for a longitudinal shear of 70 kN and moment of 10 kN.m. The minimum bolt value required (in kN) is _____________ (rounded off to the nearest integer).
Built-up column of two I-sections laced by two batten plates; each batten connects to each component with 6 bolts in two vertical lines 70 mm apart, pitch 140 mm, end distance 30 mm; battens 210 mm apart, components 100 mm apart30140140302107010070All dimensions are in mm

Answer: Official key: 21 to 24

  1. Each connection is an eccentrically loaded bolt group: 2 vertical lines 70 mm apart, 3 bolts per line at 140 mm pitch. About the group centroid the bolts sit at mm and mm.
  2. ; the corner bolts are farthest, .
  3. Direct shear, along the column axis: per bolt.
  4. Moment shear on a corner bolt acts perpendicular to its radius. Components: horizontal , vertical .
  5. On the corner bolt where the vertical parts add: , so the minimum bolt value is .

Treating the bolts as a single line ( ignored) gives 21.3 kN, also inside the key 21 to 24. Trap: adding and the full moment force as plain numbers gives 28.5 kN, outside the key; the two forces act at an angle to each other.

Where this shows up in industry

IS 800 Cl. 7.7.2.3 gives the batten design forces, longitudinal shear and moment , and the end connection is then checked exactly as an eccentric bolt group. Fabrication drawings for battened columns in industrial sheds and gantry girders (Tekla models, STAAD.Pro connection checks) carry this check for each batten.

GATE 2025 · CE2 · Q.37MCQ · 2 marksBolted and welded connections

250 mm tube welded all round with a 5 mm fillet weld, Fe410 shop weld: what torque can the weld resist?

A circular tube of thickness 10 mm and diameter 250 mm is welded to a flat plate using 5 mm fillet weld along the circumference. Assume Fe410 steel and shop welding.

As per IS 800:2007, the torque that can be resisted by the weld (in kN.m) is ______ (round off to one decimal place).
  1. (A)65.1
  2. (B)78.1
  3. (C)156.2
  4. (D)130.2

Answer: (A) 65.1 Official key: A

  1. Effective throat (IS 800 Cl. 10.5.3.2, faces at 90 degrees): .
  2. Design strength of a fillet weld (Cl. 10.5.7.1.1) with for shop welds (Table 5): .
  3. Under torsion every point of a circular weld carries the same shear, tangential, at radius mm. Weld length .
  4. , which is , option (A).

Trap: using the diameter instead of the radius as the lever arm doubles the answer: , option (D). A field weld () would give 54.2 kN.m, which is why the question says shop welding.

Where this shows up in industry

Tubular posts welded to base plates, handrail stanchions and CHS members of space frames and towers are welded all round exactly like this; the same polar-throat check sizes the weld when wind or eccentric loads twist the member. Fabricators note on drawings whether a weld is shop or site because the partial safety factor changes from 1.25 to 1.5.

GATE 2026 · CE1 · Q.30NAT · 1 markBolted and welded connections

Fillet weld size changed from 5 mm to 6 mm: what weld length transfers the same design load?

Two steel plates are to be connected together by a 5 mm fillet weld of length 150 mm to transfer a design load. If the size of the fillet weld used to connect the same two plates is changed to 6 mm, the weld length (in mm) needed for transferring the same design load is ________ (in integer).

Answer: Official key: 120 to 130

  1. IS 800 Cl. 10.5.7.1.1: a fillet weld fails in shear on its throat. Design strength , with throat and for fusion faces at (Cl. 10.5.3.2).
  2. Same plates, same electrode, same load: and cancel, so stays constant.
  3. . Answer: .
  4. If 150 mm is read as the overall length and the end craters are deducted (effective length , Cl. 10.5.4.1): mm effective, i.e. mm overall. The key range 120 to 130 accepts both readings.

Trap: making the length go with (the triangular area of the weld) gives . Strength depends on the throat, which is linear in .

Where this shows up in industry

Fabricators prefer weld sizes they can lay in one pass (about 6 to 8 mm with manual metal arc), so the detailer often trades size for length; Tekla Structures and connection tools such as IDEA StatiCa recompute the required length from the same throat-shear rule.

GATE 2026 · CE2 · Q.15MCQ · 1 markBeams and members to IS 800

Why does IS 800 limit a cantilever steel beam's design moment to 1.5 times its elastic moment capacity?

As per IS:800-2007, design of a cantilever steel beam section for its moment capacity requires fulfilment of an upper bound, expressed as:

The reason for such upper bound is to

  1. (A)control deflection
  2. (B)restrain lateral-torsional buckling
  3. (C)avoid plastic deformation under working load
  4. (D)avoid yielding at ultimate load

Answer: (C) avoid plastic deformation under working load Official key: C

  1. IS 800 Cl. 8.2.1.2: for a laterally supported beam , but not more than for a simply supported beam and for a cantilever.
  2. is checked against the factored moment. With a load factor of about 1.5 (IS 800 Table 4), a factored moment equal to the cap means a working moment of : the extreme fibre just reaches yield and no more.
  3. The cap only bites for sections with a large shape factor (a tee is about 1.8, a diamond 2.0; a rolled I-section is about 1.14). Without it, such a section could be allowed a moment that makes it yield under everyday service loads and keep a permanent set. Answer: (C).

Trap: (B). Lateral-torsional buckling is handled separately in Cl. 8.2.2 through and . (D) is wrong because yielding at ultimate load is exactly what limit state design allows.

Where this shows up in industry

This is the check that governs angles, tees and channels bent about their weak axis, for example cantilever brackets and canopy arms. STAAD.Pro's IS 800 code check reports the capped , and designers notice it when a section with an apparently generous comes out weaker than expected.

GATE 2022 · CE2 · Q.38MCQ · 2 marksPlastic analysis: shape factor and collapse loads

Shape factor and plastic moment of a square steel section bending about its diagonal (a = 100 mm)

For the square steel beam cross-section shown in the figure, the shape factor about axis is and the plastic moment capacity is . Consider yield stress = 250 MPa and = 100 mm.

The values of and (rounded-off to one decimal place) are

Solid square steel section of side a placed as a diamond with corners K (top), J (right), I (bottom) and H (left); the z-z axis passes through H and J along the horizontal diagonalKIHJzzaaaa
  1. (A), kN-m
  2. (B), kN-m
  3. (C), kN-m
  4. (D), kN-m

Answer: (A) , Official key: A

  1. Elastic modulus: a square has about any centroidal axis, and the extreme fibre (corner K) is at . So .
  2. Plastic modulus: z-z splits the section into two equal triangles, each of area and height , with centroid at one third of the height from z-z. .
  3. Shape factor: (same as any triangle-based diamond).
  4. .
  5. Answer: (A)

Trap: S = 1.5 is the value for a square bent about an axis parallel to a side; turning the square onto its corner puts less material far from the axis, so first yield comes early ( kN m) and the ratio climbs to 2.0.

Where this shows up in industry

Shape factors set how much reserve a section has beyond first yield; IS 800:2007 Table 2 classifies sections as plastic/compact before can be used, and plastic design of portal frames in tools like STAAD.Pro relies on for each member.

GATE 2023 · CE1 · Q.38MCQ · 2 marksPlastic analysis: shape factor and collapse loads

Shape factor of a plus-shaped (cruciform) steel section about its horizontal centroidal axis

Consider the horizontal axis passing through the centroid of the steel beam cross-section shown in the figure. What is the shape factor (rounded off to one decimal place) for the cross-section?

Plus-shaped steel section: a vertical bar b wide and 3b deep crossed at mid-height by a horizontal bar 3b wide and b deepbbbbbb
  1. (A)1.5
  2. (B)1.7
  3. (C)1.3
  4. (D)2.0

Answer: (B) 1.7 Official key: B

  1. The section is symmetric about the horizontal axis, so the centroid is at mid-height and the plastic (equal-area) axis coincides with it.
  2. Elastic: the vertical bar is and the two side arms are each, centred on the axis: , so .
  3. Plastic: each half has a strip at lever arm and a block at lever arm : .
  4. Shape factor
  5. Answer: (B) 1.7

Trap: (A) 1.5 is the rectangle value. The cross puts extra width at the neutral axis, where it adds little to the elastic modulus but a lot to the plastic one, so the ratio rises above 1.5 (towards the diamond's 2.0).

Where this shows up in industry

IS 800:2007 Cl. 8.2.1.2 lets plastic and compact beams use , but caps a simply supported beam at ; for a section with a shape factor of 1.7 like this one, the cap governs, which is why designers check before trusting the full plastic moment in STAAD.Pro or a spreadsheet.

GATE 2024 · CE2 · Q.33NAT · 1 markPlastic analysis: shape factor and collapse loads

Shape factor of a 150 x 120 x 30 mm steel angle with elastic section modulus 150.92 cm3

The steel angle section shown in the figure has elastic section modulus of about the horizontal axis, which passes through the centroid of the section.

(Figure NOT to scale)

The shape factor of the section is ________ (rounded off to 2 decimal places).

Unequal steel angle: vertical leg 15 cm overall height and 3 cm thick, horizontal leg 12 cm overall width and 3 cm thick; horizontal centroidal axis X-X3 cm15 cm12 cm3 cmXX

Answer: Official key: 1.75 to 1.85

  1. Areas: vertical leg , rest of the horizontal leg , total .
  2. Plastic neutral axis splits the area in half: below. The bottom 3 cm is 12 cm wide, so gives , the top of the horizontal leg.
  3. (below: at 1.5 cm; above: at 6 cm).
  4. Check : , , .
  5. Shape factor .

Answer: .

Trap: taking first moments about the elastic centroid (5.25 cm) instead of the equal-area axis gives and a shape factor of , outside the key. For unsymmetric sections the two axes differ.

Where this shows up in industry

IS 800 Cl. 8.2.1.2 gives plastic and compact sections a design moment of fyZp/γm0, so steel tables list Zp beside Ze; for angles used as lintels or bracing in bending, Tekla and STAAD.Pro section databases compute Zp about the equal-area axis exactly like this.

GATE 2025 · CE1 · Q.53NAT · 2 marksPlastic analysis: shape factor and collapse loads

T-section 60 x 5 flange, 5 x 60 web, elastic NA at 18.75 mm, plastic NA at 5 mm: what is the shape factor?

Consider the beam section shown in the figure, with indicating the depth of neutral axis (NA). The section is only subjected to an increasing bending moment. It is given that = 18.75 mm, when the section has not yielded at the top and bottom fibres. Further, decreases to 5 mm, when the entire section has yielded. The shape factor of the section is _____________ (rounded off to 2 decimal places).
T-section: flange 60 mm wide and 5 mm thick, web 5 mm thick and 60 mm deep below the flange; neutral axis NA at depth y-bar from the topNA60560y5All dimensionsare in mm

Answer: Official key: 1.80 to 1.82

  1. Shape factor . Flange and web are both ; total depth 65 mm.
  2. Elastic stage, NA at mm from the top: .
  3. Yield starts at the fibre farthest from the NA, the web tip: , so .
  4. Fully plastic stage: the NA splits the area into equal halves, at 5 mm, the flange/web junction. .
  5. Shape factor , so the answer is .

Trap: taking the plastic moments about the elastic NA (splitting the section at 18.75 mm) gives and a shape factor of 1.99. In the fully plastic state the compression and tension areas must be equal, which is why the NA moves up to 5 mm.

Where this shows up in industry

IS 800 limit state design of beams uses the plastic modulus directly, (Cl. 8.2.1.2), capped at for simply supported members. A tee has a large shape factor, so that cap and the section class decide the capacity of T-sections cut from I-beams and used as truss chords.

GATE 2026 · CE1 · Q.52NAT · 2 marksPlastic analysis: shape factor and collapse loads

Plastic section modulus of a steel T-section with a 100 × 20 mm flange and a 20 × 100 mm web

The cross-section of a steel T-beam is shown in the figure where all dimensions are in mm.
The plastic section modulus of the given cross-section is _________ (in integer).
Steel T-section: flange 100 mm wide and 20 mm thick on top of a web 20 mm thick and 100 mm deep, all dimensions in mm1002010020

Answer: , i.e. Official key: 12 to 12

  1. Areas: flange , web , total .
  2. At full plasticity every fibre is at , so the plastic neutral axis splits the area into two equal halves of . Here that is exactly the flange-web junction, 20 mm below the top.
  3. about that axis: .
  4. . Answer: 12.

Trap: taking moments about the elastic centroid (40 mm below the top) gives , which rounds to 13. The elastic modulus is different again: , , so the shape factor of this tee is .

Where this shows up in industry

is the number IS 800 uses for the bending strength of plastic and compact sections (). Steel tables (SP 6) and STAAD.Pro list it for rolled sections, but cut tees from split I-beams, used as truss chords and in built-up members, are often worked out by hand exactly like this.

GATE 2026 · CE2 · Q.49NAT · 2 marksPlastic analysis: shape factor and collapse loads

Portal frame with fixed and roller supports: combined plastic mechanism Mp = C1·PL + C2·wL², find C1/C2

A rigid-jointed portal frame, shown in the figure, consists of beam and columns of equal length . The frame has a fixed support at one end and a roller support at the other end. The frame is subjected to a uniformly distributed load and a lateral load as shown in the figure. The plastic moment capacity of the beam and column sections is . Consider a combined beam-column mechanism for plastic collapse. By applying the virtual work equation corresponding to the combined plastic collapse mechanism, is expressed as

where and are constants.

The value of is ______ (in integer).

Portal frame: left column fixed at its base, right column on a roller, beam and both columns of length L; uniformly distributed load w per unit length on the beam and horizontal load P at the top of the left columnw per unit lengthPLLL

Answer: Official key: 4 to 4

  1. Call the fixed base A, the top of the left column B, the top of the right column C and the roller D. A roller gives only a vertical reaction, so the right column carries no shear and no moment: hinges can form only at A, B or in the beam. The frame is one degree indeterminate, so a mechanism needs two hinges.
  2. Combined mechanism: hinges at A and at midspan E of the beam. A-B-E rotates by about A: B moves sideways and E drops . E-C-D rotates by about a centre vertically above D; matching the drop at E gives , so hinge E turns .
  3. External work: plus times the triangle of beam deflection, .
  4. Internal work: , so .
  5. .

Trap: taking the UDL work as the total load times the peak drop gives and a ratio of 2. Each point of the beam drops by a different amount, so use the area of the deflected triangle.

Where this shows up in industry

Single-storey steel portals for warehouses and industrial sheds are designed plastically: the engineer checks the beam, sway and combined mechanisms by virtual work, and the lowest collapse load governs. The same hand check is used to sanity-test the collapse load factor reported by plastic-analysis software.

From GATE prep to a steel design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.