GATE Civil: Geomatics Engineering (surveying, levelling, bearings and traversing, photogrammetry), previous-year questions solved
Every geomatics (surveying) question from the ten official GATE Civil papers of 2022-2026: 36 questions (14 NAT, 22 MCQ) on surveying principles, errors and maps, levelling, distance and angle measurement, traversing and photogrammetry, each solved step by step and checked by a script against the official key. GATE 2027 adds GNSS surveying, map projections and parallax equations to this section and drops curves and remote sensing.
Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 15 of 36 questions on this page
New coordinates of point (1, 1, 1) after the axes are rotated 45 degrees clockwise about the positive x-axis
The Cartesian coordinates of a point P in a right-handed coordinate system are (1, 1, 1). The transformed coordinates of P due to a 45° clockwise rotation of the coordinate system about the positive -axis are
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- A rotation about the -axis does not change , so . That rules out (C) and (D).
- Look down the axis: points right, points up, and P sits at 45° between them, from the axis.
- Turning the axes 45° clockwise swings down towards and across to the old 45° line, which is exactly where P is. So P lies on the new axis: , .
- Same result from the transformation, with : and .
- Answer: (A) .
Trap: every option keeps the distance from the origin, so a length check cannot pick one. Rotating the axes the other way would give , not offered; the sign of comes from where P ends up relative to the turned axes.
Moving survey points between a local site grid and a national or UTM grid is a rotation plus a shift and a scale factor (a Helmert transformation); total station and GIS software apply it every time site control is tied to GNSS coordinates.
Slope of the ground between adjacent contours 10 mm apart on a 1:1000 map with a 1 m contour interval
A map is prepared with a scale of 1: 1000 and a contour interval of 1 m. If the distance between two adjacent contours on the map is 10 mm, the slope of the ground between the adjacent contours is
- (A)30%
- (B)10%
- (C)35%
- (D)40%
Answer: (B) 10% Official key: B
- At 1:1000, 1 mm on the map is 1000 mm = 1 m on the ground.
- Horizontal equivalent between the two contours: .
- The vertical drop between adjacent contours is the contour interval, 1 m.
- Slope , that is 1 in 10 (about ).
- Answer: (B) 10%.
Trap: forgetting to convert the map distance to ground units. 1 m over 10 mm would be a 10,000 % slope; the scale must be applied before dividing. Closely spaced contours mean steep ground and wide spacing means gentle ground, so 10 mm at 1:1000 is a gentle slope.
Road and canal alignment studies still start this way: designers read the horizontal equivalent between contours on a topographic map or a digital terrain model to keep a route within its ruling gradient before any detailed survey is ordered.
Most probable value of a bearing from four equal-precision theodolite observations of the same tower
To finalize the direction of a survey, four surveyors set up a theodolite at a station P and performed all the temporary adjustments. From the station P, each of the surveyors observed the bearing to a tower located at station Q with the same instrument without shifting it. The bearings observed by the surveyors are , , and . Assuming that each measurement is taken with equal precision, the most probable value of the bearing is
- (A)
- (B)
- (C)
- (D)
Answer: (B) Official key: B
- For observations of one quantity with equal weights, the most probable value is the arithmetic mean (it minimises the sum of squared residuals).
- Write each reading as seconds above : 60, 40, 80 and 140; total .
- Mean excess , so the mean is .
- Is an outlier? Residuals are , standard deviation , so its , below Chauvenet's limit of for four readings. Keep it.
- Answer: (B) .
Trap: discarding the largest reading as a mistake gives the mean of three, , which is (C). With equal precision and no reading failing a rejection test, all four stay in.
Control surveys observe each direction on several rounds and both faces and take the mean, and least-squares adjustment software extends the same idea to whole networks, weighting each observation by its precision.
How does the error due to the curvature of the earth grow with the distance to the staff?
If the horizontal distance between a staff point and the point of observation is , the error due to the curvature of earth is proportional to
- (A)
- (B)
- (C)
- (D)
Answer: (C) Official key: C
- A level line of sight is horizontal at the instrument, but the level surface curves away below it. At distance the line of sight is higher than the level surface by .
- The right triangle formed by the earth's centre, the instrument and the staff gives , so .
- is a few centimetres while is 6370 km, so is negligible: .
- With in km and in m: . Doubling the distance from 1 km to 2 km raises it from m to m, four times.
- The error is proportional to , option (C).
Trap: (A). The correction is a length, so it is tempting to make it linear in , but it comes from the geometry of a circle. Refraction bends the sight back down by about one seventh, so the combined correction is , still proportional to .
On normal construction levelling the sights are kept under about 50 m and balanced, so curvature cancels out. It matters for long sights across rivers and valleys, and for trigonometric heights from a total station, where the instrument software applies the curvature and refraction correction automatically.
Distance measured on a 1 cm = 40 m plan with a 1 cm = 20 m scale: the true distance
A surveyor measured the distance between two points on the plan drawn to a scale of 1 cm = 40 m and the result was 468 m. Later, it was discovered that the scale used was 1 cm = 20 m.
The true distance between the points (in m) is ______ (round off to the nearest integer).
Answer: 936 m Official key: 936 to 936
- The plan is drawn to 1 cm = 40 m (RF ). The surveyor read the length with a scale graduated for 1 cm = 20 m (RF ) and got 468 m.
- Length on the paper: cm.
- On this plan 1 cm stands for 40 m, so the true distance is m.
- Same result with the textbook rule: true length measured length RF of the scale used / RF of the plan m.
Trap: reading it the other way round (the plan was really at 1 cm = 20 m) gives m. The sentence can be read that way, but the official key is 936 only, so IIT Roorkee meant 'the measuring scale used was 1 cm = 20 m'.
Scanned old village maps and printed drawings are often enlarged or reduced, so the scale bar, not the stated ratio, is the reference. When a plan is georeferenced in GIS or digitised in AutoCAD, checking one known distance first catches exactly this kind of factor-of-two error.
Levelling survey: level surface normal to gravity, crossing level surfaces, the ellipsoid and the geoid
Which one of the following statements is TRUE with respect to levelling survey?
- (A)A level surface at all points is normal to the direction of the force of gravity.
- (B)Two level surfaces can cross each other.
- (C)Ellipsoid is an irregular surface approximating the physical surface of the Earth.
- (D)Geoid is a regular surface approximating the physical surface of the Earth.
Answer: (A) A level surface at all points is normal to the direction of the force of gravity. Official key: A
- (A) TRUE: a level surface is a surface of constant gravity potential (an equipotential surface), so at every point it is perpendicular to the plumb line, which is what a levelled instrument's bubble finds.
- (B) FALSE: level surfaces of different potential are nested inside one another; if two crossed, one point would have two potentials.
- (C) FALSE: the ellipsoid is a regular mathematical surface (an ellipse rotated about its minor axis) chosen to fit the geoid, which is why it is used for geodetic coordinates.
- (D) FALSE: the geoid is the equipotential surface that best fits mean sea level, and it is irregular because the Earth's mass is unevenly distributed.
- Answer (A).
Trap: (C) and (D) swap the two reference surfaces. Regular is the ellipsoid, irregular is the geoid; and neither one follows the physical ground surface.
GNSS receivers give heights above the WGS 84 ellipsoid, while levelling and the Survey of India benchmarks give heights above mean sea level; surveyors convert between them with a geoid model, because the gap between the two surfaces varies from place to place.
Walking distance for 12.0 cm measured on a 1:25000 city map along a straight road
A tourist visiting a city holds a map prepared at a scale of 1:25000. The tourist measures the distance between place A and place B in the city as 12.0 cm on the map. Assuming both the places are connected by a straight road, the distance (in km) the tourist needs to walk from A to B is ______ (rounded off to the nearest integer).
Answer: 3 km Official key: 3 to 3
- A representative fraction of 1:25000 means 1 unit on the map is 25000 of the same units on the ground.
- Ground distance cm.
- (1 cm on the map is 250 m on the ground).
- Answer 3 km.
Trap: slipping a factor of 10 in the unit change (cm to m to km) gives 30 km or 0.3 km, both outside the key.
Survey of India topographic sheets are published at scales such as 1:50000 and 1:25000, and a planner reading a route, catchment or alignment off them converts map centimetres to ground distance exactly this way before any field survey is done.
Reduced level of a hillock top by trigonometric levelling from two in-line stations 55 m apart, one benchmark
Trigonometric levelling was carried out from two stations P and Q to find the reduced level (R. L.) of the top of hillock, as shown in the table. The distance between Stations P and Q is 55 m. Assume Stations P and Q, and the hillock are in the same vertical plane. The R. L. of the top of the hillock (in m) is ______ (round off to three decimal places).
| Station | Vertical angle of the top of hillock | Staff reading on benchmark | R. L. of benchmark |
|---|---|---|---|
| P | 2.340 m | 100.000 m | |
| Q | 1.660 m |
Answer: 137.628 m Official key: 137.500 to 137.730
- The larger angle is seen from the nearer station, so P is between Q and the hillock (figure). Let be the horizontal distance from P to the top.
- Heights of instrument from the benchmark: m and m.
- The top is at and also at .
- With and : .
- m.
- R.L. , giving 137.628 m. From Q: m, the same.
- Curvature and refraction ( m, in km) are tiny at 104 m and 159 m: applied to both sights the R.L. becomes 137.631 m.
Trap: forgetting that the two instrument heights differ by 0.68 m gives 139.67 m, and putting the stations on opposite sides of the hill gives 109.40 m; both are outside the key.
Heights of points that cannot be occupied, such as a hill top, tower or chimney, are still fixed this way. A total station does it from one setup by measuring the zenith angle and a reflectorless slope distance to the top.
A bird flies parallel to ground with a 1 in 2 falling gradient from 8 m to 3 m above MSL: horizontal distance
A bird is resting on a point P at a height of 8 m above the Mean Sea Level (MSL). Upon hearing a loud noise, the bird flies parallel to the ground surface and reaches a point Q which is located at a height of 3 m above MSL. The ground surface has a falling gradient of 1 in 2. Ignoring the effects of curvature and refraction, the horizontal distance (in meters) between points P and Q is ______ (in integer).
Answer: 10 m Official key: 10 to 10
- Flying parallel to the ground means the bird keeps the same height above the ground all the way, so its path falls exactly as fast as the ground does.
- Fall in level from P to Q: .
- A falling gradient of 1 in 2 means 1 m of fall for every 2 m of horizontal distance.
- Horizontal distance .
- Answer: 10 m.
Trap: the length along the slope is , not the horizontal distance; and reading 1 in 2 as 2 m of fall per metre gives 2.5 m. Gradients in surveying are always vertical : horizontal.
Gradients written as 1 in n are how levels are set out on site: a drain or ramp laid at 1 in 100 drops 10 mm per metre, and the surveyor converts each chainage into a required reduced level for the staff.
Differential levelling from a BM of 200.000 m with inverted staff readings and a change point: RL of R
Differential levelling is carried out from point P (BM: +200.000 m) to point R. The readings taken are given in the table.
| Points | Back Sight (m) | Fore Sight (m) | Remarks |
|---|---|---|---|
| P | (−)2.050 | BM: +200.000 m | |
| Q | 1.050 | 0.950 | Q is a change point |
| R | (−)1.655 |
Reduced Level (in meters) of the point R is _____ (rounded off to 3 decimal places).
Answer: 199.705 m Official key: 199.704 to 199.706
- A negative reading means the staff was held inverted, its foot against a point above the line of sight (a ceiling or the underside of a beam). Keep the sign and use the usual height of instrument (HI) method.
- First set-up: ; RL of Q .
- Second set-up: ; RL of R .
- Check: , and plus that is 199.705 m.
- Answer: 199.705 m.
Trap: dropping the minus signs and treating both inverted readings as ordinary ones gives 200.495 m. An inverted back sight lowers the HI and an inverted fore sight puts the point above the line of sight.
Inverted staff readings are routine when levelling soffits of bridges, slab undersides and tunnel crowns; digital levels have an inverted-staff mode that flips the sign automatically, and forgetting it is a classic as-built survey error.
Reciprocal levelling across a river: what is the reduced level of B from readings with the level at A and at B?
In levelling between two points A and B on the opposite banks of a river, the readings are taken by setting the instrument both at A and B, as shown in the table. If the RL of A is 150.000 m, the RL of B (in m) is ________ (rounded off to 3 decimal places).
| Level position | Staff reading on A | Staff reading on B |
|---|---|---|
| A | 1.800 | 1.350 |
| B | 1.450 | 0.950 |
Answer: 150.475 m Official key: 150.470 to 150.480
- The sight across the river is long, so the far reading carries the collimation, curvature and refraction error . Setting up at both ends puts that error on B's reading once and on A's reading once, and averaging cancels it.
- Level near A: m (B is higher, because its reading is smaller).
- Level near B: m.
- True difference: m, B above A.
- m, inside the key 150.470 to 150.480.
- Check: the combined error of the long sight is m per reading.
Trap: using one set-up only gives m (level at A) or m (level at B), both outside the key; subtracting because B 'reads less' gives m.
Carrying a benchmark across a river for a bridge or a barrage is done exactly this way, with readings taken from both banks as close together in time as possible so the refraction is the same. Highway and railway bridge surveys still specify reciprocal levelling when the gap is too wide to balance sights.
Reduced level of a ground point from the height of collimation 100.000 m and a back sight of 1.500 m
The height of the plane of collimation of a levelling instrument is 100.000 m from a datum. The levelling instrument measures a Back Sight of 1.500 m on a vertically held staff at a ground point P. The reduced level (in m) of the ground point P with respect to the datum is ______ (rounded off to three decimal places).
Answer: 98.500 m Official key: 98.500 to 98.500
- The height of collimation (height of instrument, HI) is the reduced level of the line of sight.
- The staff reading at P is the vertical distance from the line of sight down to P, so .
- m.
- Answer 98.500 m.
Trap: the usual rule is , so adding the back sight again gives 101.500 m, outside the key. Here the HI is already known, and any staff reading, back sight or not, is subtracted from it.
This is how a site engineer sets formation levels with an auto level: one back sight on a benchmark fixes the height of instrument, and every pile cap, footing or road level is then read as height of instrument minus the staff reading.
Reciprocal levelling across a wide valley: differences of 3.0 m and -1.0 m from the two ends, true difference
Locations P and Q are separated by a wide valley. The difference in levels of locations P and Q measured by a levelling instrument stationed near P is 3.0 m. The same instrument stationed near Q measures the difference in levels of locations P and Q as −1.0 m. Assume that the atmospheric refraction is same during the measurements. The true difference in levels (in m) of locations P and Q is
- (A)1.0
- (B)1.5
- (C)2.0
- (D)4.0
Answer: (A) 1.0 Official key: A
- Across a valley the back and fore sights cannot be balanced. With the instrument near P, the long sight to Q carries an error (curvature, refraction and any collimation error), so the observed difference is .
- With the instrument near Q, the long sight is to P and the same error enters the other reading, so the observed difference is .
- and , so m and m.
- Answer (A) 1.0 m.
Trap: half the difference of the two observations, , is the error , option (C), not the true difference. For scale: if all of were curvature and refraction, gives a sight of about 5.5 km.
Bridge and pipeline crossings use reciprocal levelling to carry a benchmark across a river: two instruments read simultaneously from both banks so the refraction is the same, and the mean of the two differences cancels curvature, refraction and collimation error together.
Gradient of the ground from ten dumpy level readings at 20 m intervals with the level shifted after the sixth
The following consecutive readings (in m) were taken with a dumpy level and a levelling staff at a common interval of 20 m:
0.385; 1.030; 1.925; 2.825; 3.730; 4.850; 1.045; 2.005; 3.330; 4.580
The dumpy level was shifted after taking the sixth reading.
The gradient (in %) of the ground between the first and the last location of the reading is ______ (in integer).
Answer: -5 % (a falling gradient; the key accepts −5 or 5) Official key: -5 to -5 OR 5 to 5
- Book the readings: the first is a back sight (BS), the sixth a fore sight (FS) on the change point (CP); after the shift, the seventh is a BS on the same CP and the tenth the closing FS. The rest are intermediate sights (IS).
- So there are 9 staff stations, not 10, and the first-to-last distance is m.
- Fall m.
- Check with the height of instrument method (RL of station 1 assumed 100.000):
| Station | BS | IS | FS | HI | RL |
|---|---|---|---|---|---|
| 1 | 0.385 | 100.385 | 100.000 | ||
| 2 | 1.030 | 99.355 | |||
| 3 | 1.925 | 98.460 | |||
| 4 | 2.825 | 97.560 | |||
| 5 | 3.730 | 96.655 | |||
| 6 (CP) | 1.045 | 4.850 | 96.580 | 95.535 | |
| 7 | 2.005 | 94.575 | |||
| 8 | 3.330 | 93.250 | |||
| 9 | 4.580 | 92.000 |
- Gradient per cent, a fall from the first station to the last.
- Answer -5 %.
Trap: counting 10 stations (180 m) gives -4.44 %, and differencing the first and last readings across the change of set-up gives -2.62 %; both round outside the key.
Longitudinal sections for roads, canals and sewers are levelled exactly like this, with staff readings at a fixed chainage interval and change points wherever the staff goes out of view; the reduced levels give the existing ground gradient against which the design gradient and earthwork are set.
Levelling from benchmark L (RL 150.000 m) to N with two set-ups: match the sum of BS, sum of FS and RL of N
For the traverse given below, the benchmark is at ground point L. The Reduced Level (RL) of L is 150.000 m. The direction of the traverse is from L to N. The readings on levelling staff using the same levelling instrument kept at Stations S1 and S2 during the traversing are shown in the figure.
| Column 1 | Column 2 |
|---|---|
| (P) 3.300 m | |
| (I) Sum of Back Sights | (Q) 2.500 m |
| (II) Sum of Fore Sights | (R) 150.300 m |
| (III) RL of Point N | (S) 3.000 m |
| (T) 150.500 m |
Matching the information given under Column 1 and Column 2, which one of the following options is CORRECT?
- (A)(I) – (P) ; (II) – (S) ; (III) – (R)
- (B)(I) – (P) ; (II) – (Q) ; (III) – (R)
- (C)(I) – (S) ; (II) – (P) ; (III) – (T)
- (D)(I) – (S) ; (II) – (Q) ; (III) – (T)
Answer: (A) (I) – (P) ; (II) – (S) ; (III) – (R) Official key: A
- Going from L to N, the reading on the staff behind the instrument is the back sight (BS) and the one ahead is the fore sight (FS). At S1: BS on L is 1.5 m and FS on M is 2.0 m. At S2: BS on M is 1.8 m and FS on N is 1.0 m; M is the change point.
- m, (P).
- m, (S).
- m; m, (R). Check: m.
- Answer (A).
Trap: swapping back and fore sights (reading the line from N to L) makes the sums 3.000 and 3.300 and gives an RL of 149.700 m, which is not offered; option (C) pairs those swapped sums with 150.500 m.
Every level book ends with this arithmetic check: the sum of back sights minus the sum of fore sights must equal the last reduced level minus the first; a mismatch means a booking or reading blunder that has to be found before the levels are used for design.