GATE Civil: Soil Mechanics (phase relations, classification, permeability and seepage, effective stress, compaction, consolidation, shear strength), previous-year questions solved
Every soil mechanics question from the ten official GATE Civil papers of 2022-2026 (CE1 and CE2 each year): 45 questions (22 NAT, 19 MCQ, 4 MSQ) on phase relations and classification, permeability, seepage and effective stress, compaction, consolidation and shear strength, each solved step by step and checked by a script against the official key. The GATE 2027 syllabus keeps every soil mechanics line unchanged.
Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 13 of 45 questions on this page
Void ratio of a soil heap (10000 m3, e = 1) after it is compacted to 7500 m3
An uncompacted heap of soil has a volume of 10000 m3 and void ratio of 1. If the soil is compacted to a volume of 7500 m3, then the corresponding void ratio of the compacted soil is __________. (round off to one decimal place)
Answer: Official key: 0.5 to 0.5
- Compaction squeezes out air, not solids, so the volume of solids stays the same.
- Before compaction: , so .
- After compaction: , so .
- Equivalent shortcut: .
- Answer:
Trap: scaling the void ratio by the volume ratio, , is wrong because the volume of solids does not shrink; the whole 2500 m3 reduction comes out of the voids.
This is the loose-to-compacted conversion behind every earthwork estimate for highway and rail embankments: borrow-pit quantities are worked out from the in-situ and specified compacted dry densities so that the contractor excavates enough soil to build the bank.
Match normally consolidated soil, quick clay, critical-state sand and high-plasticity clay to their conditions
The correct match between the physical states of the soils given in Group I and the governing conditions given in Group II is
| Group I | Group II |
|---|---|
| 1. normally consolidated soil | P. sensitivity |
| 2. quick clay | Q. dilation angle |
| 3. sand in critical state | R. liquid limit |
| 4. clay of high plasticity | S. over consolidation ratio |
- (A)1-S, 2-P, 3-Q, 4-R
- (B)1-Q, 2-S, 3-P, 4-R
- (C)1-Q, 2-P, 3-R, 4-S
- (D)1-S, 2-Q, 3-P, 4-R
Answer: (A) 1-S, 2-P, 3-Q, 4-R Official key: A
- Normally consolidated: the present effective overburden is the largest it has ever carried, so . 1-S.
- Quick clay: sensitivity . Clays with are called quick: on remoulding they turn almost liquid. 2-P.
- Critical state: the sand keeps shearing at constant volume and constant stresses, so the volumetric strain increment is zero and the dilation angle . 3-Q.
- High plasticity: on the plasticity chart, H means liquid limit above 50 % (IS 1498 uses 35-50 as intermediate). 4-R.
- Answer: (A) 1-S, 2-P, 3-Q, 4-R
Trap: (D) pairs quick clay with zero dilation and critical-state sand with sensitivity. Zero dilation is the defining feature of the critical state, while sensitivity is a property of structured clays, not sands.
These descriptors go straight into soil investigation reports: OCR from oedometer tests (IS 2720 Part 15) decides whether soft marine clays at port sites such as Mumbai or Kochi will settle a lot, and vane-shear sensitivity warns of strength loss during pile driving.
Void ratio of a soil with G = 2.60 at 50% degree of saturation and 15% water content
The specific gravity of a soil is 2.60. The soil is at 50% degree of saturation with a water content of 15%. The void ratio of the soil is ________ .
- (A)0.35
- (B)0.78
- (C)0.87
- (D)1.28
Answer: (B) 0.78 Official key: B
- Take a soil with unit volume of solids. Solids weigh , water weighs , so the volume of water is . The voids have volume , and the fraction of them filled with water is .
- Hence the phase relation , valid for any degree of saturation.
- Check: porosity , a plausible value for a partly saturated silty soil.
- Answer: (B) 0.78
Trap: (D) 1.28 is , the relation written upside down. Using by habit gives , which is not even an option; 50% saturation means the voids are twice the water volume.
Lab reports for road and building sites (IS 2720 Part 2 for water content, Part 3 for specific gravity) give and directly; engineers then back out and with to check the in-situ density results and to feed void ratio into settlement calculations.
Grain shape near the source of mechanical weathering, and what clay activity signifies
Consider the statements P and Q.
P: Soil particles formed by mechanical weathering, and close to their origin are generally subrounded.
Q: Activity of the clay physically signifies its swell potential.
Which one of the following options is CORRECT?
- (A)Both P and Q are TRUE
- (B)P is TRUE and Q is FALSE
- (C)Both P and Q are FALSE
- (D)P is FALSE and Q is TRUE
Answer: (D) P is FALSE and Q is TRUE Official key: D
- P: mechanical weathering (frost action, temperature cycling, abrasion) breaks rock into fragments with sharp edges. Close to the parent rock these grains are angular to subangular. They become subrounded or rounded only after transport by water or wind wears the corners off. P is FALSE.
- Q: Skempton's activity is . It measures how much plasticity each unit of clay brings, which depends on the clay mineral: kaolinite , illite , montmorillonite 1 to 7.
- Minerals with high activity hold more water in their double layers and swell more, so activity is used as an index of swell potential. Q is TRUE.
Answer: (D) P is FALSE and Q is TRUE.
Trap: picking (A) because sand grains you see in rivers are rounded. Those grains have been transported; residual grains near their origin are angular.
Black cotton soils across Maharashtra, Madhya Pradesh and Karnataka are flagged on site by their high activity and free swell index (IS 2720 Part 40), which decides whether a footing, canal lining or road subgrade needs CNS cushioning, under-reamed piles or lime treatment.
Shrinkage limit and swell, critical void ratio of sands, SPT correction order, ERT depth
Which of the following statement(s) is/are CORRECT?
- (A)Swell potential of soil decreases with an increase in the shrinkage limit.
- (B)Both loose and dense sands with different initial void ratios can attain similar void ratio at large strain during shearing.
- (C)Among the several corrections to be applied to the SPT-N value, the dilatancy correction is applied before all other corrections.
- (D)In electrical resistivity tomography, the depth of current penetration is half of the spacing between the electrodes.
Answer: (A) and (B) Official key: A;B
- (A) TRUE. The shrinkage limit is the water content below which the soil stops losing volume. A high means a small range of volume change on wetting and drying, so the swell potential is low. IS 1498 classes as low and as high degree of expansion.
- (B) TRUE. In drained shear a loose sand contracts and a dense sand dilates. At large strain both reach the same critical (constant-volume) void ratio for a given confining stress.
- (C) FALSE. The overburden correction is applied first to give ; the dilatancy correction is applied afterwards, and only to fine or silty sand below the water table with .
- (D) FALSE. For the Wenner array the usual rule is that the depth of investigation is about equal to the electrode spacing , not .
Answer: (A) and (B).
Trap: ticking (C) because the dilatancy correction is often listed first in older texts. It works on the overburden-corrected value, so it has to come second.
Before building on expansive black cotton soil, IS 1498 swell indicators (shrinkage limit, free swell, plasticity) are read off the routine IS 2720 lab sheet; the critical void ratio idea is what separates contractive loose sands that can liquefy under IS 1893 shaking from dense ones.
Density index of a sand with 50% voids, maximum and minimum densities 1.8 and 1.3 g/cm3, G = 2.7
The in-situ percentage of voids of a sand deposit is 50%. The maximum and minimum densities of sand determined from the laboratory tests are and , respectively. Assume the specific gravity of sand as 2.7.
The relative density index of the in-situ sand is ________ (rounded off to 2 decimal places).
Answer: (13%) Official key: 0.12 to 0.14 OR 12 to 14
- Percentage of voids is the porosity, so . In-situ void ratio: .
- The laboratory maximum and minimum densities are dry densities of the densest and loosest states, so they fix the limiting void ratios through : and .
- Density index: .
- Check with densities: and .
Answer: (about 13%: a very loose sand).
Trap: interpolating linearly in density, . Density index is linear in void ratio, not in density, hence the extra factor.
Density index tests to IS 2720 Part 14 are used to specify compaction of sand fills behind retaining walls and in reclamation, and to judge whether a loose saturated sand layer is susceptible to liquefaction before deciding on vibro-compaction or stone columns.
Plasticity chart, point X above the A-line with liquid limit over 50: what soil is it (IS classification)?
The standard plasticity chart for the classification of a fine-grained soil is shown in the figure. As per the Indian standard soil classification system, X represents
- (A)inorganic clay with medium plasticity
- (B)inorganic silt with medium plasticity
- (C)inorganic clay with high plasticity
- (D)inorganic silt with high compressibility
Answer: (C) inorganic clay with high plasticity Official key: C
- IS 1498 splits fine-grained soils by liquid limit: low (), intermediate () and high () plasticity/compressibility. These are the two dashed lines at 35 and 50.
- The A-line, , separates inorganic clays (above, C) from silts and organic soils (below, M or O).
- Point X lies to the right of and above the A-line, so it is CH: inorganic clay with high plasticity, option (C).
Trap: option (D) is MH, the zone to the right of 50 but below the A-line. Option (A), CI, is above the A-line but between 35 and 50.
Every borelog and soil investigation report in India classifies the samples to IS 1498 from Atterberg limits (IS 2720 Part 5); the expansive black cotton soils of Maharashtra and Madhya Pradesh typically plot as CH, which is what triggers special subgrade and foundation measures.
Clay with w = 18%, G = 2.74, S = 65% soaks up water to S = 85.2% at constant volume: new moisture content
A clayey soil has a moisture content of 18%, a specific gravity of soil solids of 2.74, and a degree of saturation of 65%. The soil soaks up water during a rain event, and the degree of saturation increases to 85.2%. The change of the volume during the soaking is negligible. The new moisture content (in %) of the soil will be ____________________ (rounded off to 2 decimal places).
Answer: Official key: 23.30 to 23.70
- Phase relation: .
- Before soaking: .
- The volume does not change and the solids do not change, so stays .
- After soaking: , i.e. .
- Shortcut: at constant and , , so .
Trap: taking (the saturated formula, ignoring ) gives , outside the key. The soil is only partly saturated, so must be in the relation.
Rain on a compacted clay fill or subgrade raises its water content at almost constant volume, which is why highway and embankment specifications (MoRTH Section 300) require moisture checks and, if needed, drying before the next layer is placed; the same S e = w G relation converts field water contents into degree of saturation in IS 2720 test reports.
Soil with w = 15%, S = 67%, e = 0.6, G = 2.67: weight of water needed to fully saturate 5 m3 of it
For a partially saturated soil deposit at a construction site, water content (w) is 15%, degree of saturation (S) is 67%, void ratio (e) is 0.6 and specific gravity of solids in the soil () is 2.67. Consider unit weight of water as 9.81 kN/m3.
To fully saturate 5 m3 of this soil, the required weight of water (in kN) will be ______ (round off to the nearest integer).
- (A)5
- (B)6
- (C)7
- (D)8
Answer: (B) 6 Official key: B
- Volume of voids in : .
- Only the air voids need filling: .
- Weight of water , so about 6 kN, option (B).
- Check through water contents: , , extra water , also 6.
Trap: taking the voids as instead of gives , which is not even an option. The void ratio is voids per unit volume of solids, not of total soil.
The same three-phase arithmetic sets how much water a tanker must add per cubic metre of borrow soil to bring it to the target moisture before compaction in highway and embankment works, and converts core-cutter or sand-replacement densities (IS 2720 Parts 29 and 28) into void ratio and saturation.
Plasticity index range of inorganic clays with a liquid limit of 40 % on Casagrande's plasticity chart
Based on the Casagrande’s plasticity chart, plasticity index (in %) of inorganic clays having a liquid limit of 40 %, ranges between
- (A)18.0 and 28.8
- (B)14.6 and 28.8
- (C)14.6 and 23.4
- (D)18.0 and 43.8
Answer: (B) 14.6 and 28.8 Official key: B
- On the plasticity chart ( against ), inorganic clays plot above the A-line; silts and organic soils plot below it. No natural soil plots above the U-line, the empirical upper bound.
- A-line: .
- U-line: .
- So an inorganic clay with has between 14.6 and 28.8. Answer: (B) 14.6 and 28.8.
Trap: the distractors mix up the two lines. (A) uses the U-line slope with the A-line intercept, ; (C) uses the A-line slope with the U-line intercept, . Learn each line as a pair: 0.73 with 20, 0.9 with 8.
Every soil investigation report in India classifies fine-grained soils to IS 1498 using the liquid and plastic limits from IS 2720 (Part 5) plotted on this chart; the CI/CH label then decides, for example, whether a borrow soil is acceptable for a highway embankment or subgrade under the MoRTH specifications.
Plastic limit of a soil with natural water content 30 %, plasticity index 40 % and liquidity index 50 %
A soil sample has following properties:
Natural water content = 30 %
Plasticity index = 40 %
Liquidity index = 50 %
The estimated plastic limit (in %) of the soil is ________ (rounded off to one decimal place).
Answer: Official key: 10.0 to 10.0
- Liquidity index: , which places the natural water content between the plastic limit () and the liquid limit ().
- Substitute , , : .
- . Then and the consistency index , consistent with .
- Answer: .
Trap: writing the liquidity index with the liquid limit in the numerator, (that is the consistency index), gives , and reporting 50.0 as the plastic limit. The plastic limit is the lower end of the plastic range, so it must be below the natural water content here.
Borehole logs in Indian site investigation reports list natural water content beside the IS 2720 (Part 5) Atterberg limits; a liquidity index near 0.5 or above flags a soft, compressible clay, which tells the geotechnical engineer to plan undrained strength and consolidation tests before choosing a foundation.
Compaction test: which statement on peak point, compaction effort, OMC and zero-air-voids curve is incorrect
With reference to the compaction test conducted on soils, which of the following is INCORRECT?
- (A)Peak point of the compaction curve gives the maximum dry unit weight and optimum moisture content
- (B)With increase in the compaction effort, the maximum dry unit weight increases
- (C)With increase in the compaction effort, the optimum moisture content decreases
- (D)Compaction curve crosses the zero-air-voids curve
Answer: (D) Compaction curve crosses the zero-air-voids curve Official key: D
- (A) Correct. The dry unit weight versus water content curve rises, peaks and falls; the peak defines and the optimum moisture content (OMC).
- (B) and (C) Correct. A heavier rammer or more blows (modified instead of standard Proctor) packs the particles more closely at lower water content, so the peak moves up and to the left: higher , lower OMC.
- (D) Incorrect. At water content and air content , . The zero-air-voids line is the case , the largest possible value. With and : ZAV , while 5% air gives . Compaction never expels all the air, so the curve stays below and only approaches the ZAV line on the wet side.
- Answer: (D)
Trap: (C). It sounds wrong because more effort feels as if it should need more water, but the higher energy does the work that the water's lubrication did, so the OMC falls.
On NHAI and state highway embankments, MoRTH specifications require field dry density of each layer to be a set percentage of the IS 2720 Part 7/8 Proctor maximum; a field result plotting above the zero-air-voids line is the classic sign of a wrong specific gravity or a faulty sand-replacement test.
Dry unit weight of an embankment compacted at 75% saturation, 17% water content and G = 2.68
An embankment is constructed with soil by maintaining the degree of saturation as 75% during compaction. The specific gravity of soil is 2.68 and the moisture content is 17% during compaction. Consider the unit weight of water as . The dry unit weight (in ) of the compacted soil is ________ (rounded off to 2 decimal places).
Answer: Official key: 16.60 to 16.80
- Phase relation linking the four quantities: .
- Void ratio: .
- Dry unit weight: .
- Check with the compaction-curve form: , the line of constant 75% saturation on a Proctor plot.
Answer: .
Trap: dropping (taking ) gives the zero-air-voids value . That is the theoretical upper bound at 17% water content, not the density of a soil that still has 25% of its voids filled with air.
MoRTH Section 300 requires highway embankment layers to reach at least 95% (subgrade 97%) of the maximum dry density from the IS 2720 Part 8 heavy compaction test; the site lab checks each layer with sand replacement (IS 2720 Part 28) and back-calculates air voids exactly this way.