GATE Civil: Structural Analysis (trusses, deflections, indeterminate structures, influence lines), previous-year questions solved

Every structural analysis question from the ten official GATE Civil papers of 2022-2026: 28 questions (12 NAT, 11 MCQ, 5 MSQ) on determinacy and trusses, deflections by energy and moment-area methods, indeterminate beams and frames (consistent deformation, slope deflection, moment distribution, stiffness matrix) and influence lines, each solved step by step and checked by a script against the official key. GATE 2027 adds determinate arches and cables by name and lists virtual work and Castigliano's second theorem explicitly.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 15 of 28 questions on this page

GATE 2022 · CE1 · Q.50NAT · 2 marksDeterminacy, trusses, frames, arches and cables

Force in member EF of a plane truss made of two parts joined at E, under a 70 kN load

The plane truss shown in the figure is subjected to an external force . It is given that kN, m, and m.

The magnitude (absolute value) of force (in kN) in member EF is ______. (round off to the nearest integer)

Plane truss. Left part: A at the base on a pin support, B and C above it at heights a and 2a; top chord C, D, E at spacing a; an internal joint below D at height a joined to B, C, D and lying on the straight diagonal from A to E. Right part: top chord E, G, I at spacing a; bottom chord F, H, J a depth b below; verticals EF, GH, IJ; diagonals FG and GJ; J on a pin support. The two parts share only joint E, where the vertical load P acts downwards. P = 70 kN, a = 2 m, b = 3 mABCDEGIFHJPaaaaaab

Answer: 30 kN Official key: 28 to 32

  1. The truss is two rigid parts that meet only at joint E, with pins at A and J: a three-hinged arch. Take A as the origin, so E is at (4, 4) m and J at (8, 1) m.
  2. The left part carries no load between A and E, so the reaction at A acts along AE, at 45°: .
  3. Moments about J for the whole truss: , so kN. Then kN and kN towards A.
  4. Joint I has two perpendicular members and no load, so GI = IJ = 0; at H, GH = 0 and FH = HJ.
  5. Joint J (tension positive, GJ at ): vertical gives kN; horizontal gives kN.
  6. Joint F: horizontal gives kN; vertical gives kN.
  7. Answer: 30 kN (compression).

Trap: treating J as a roller (vertical reaction only) gives kN and kN, outside the key. Both supports are pins, and the pin at J supplies the 40 kN horizontal thrust.

Where this shows up in industry

Splitting a truss into rigid parts joined by pins is how engineers check three-hinged roof arches and bridge trusses by hand before trusting a frame model. A hand value close to the software output catches modelling errors such as a support entered as a roller instead of a pin.

GATE 2022 · CE2 · Q.16MCQ · 1 markDeterminacy, trusses, frames, arches and cables

Static and kinematic degrees of indeterminacy of a beam fixed at one end and hinged at the other

Consider a beam PQ fixed at P, hinged at Q, and subjected to a load as shown in figure (not drawn to scale). The static and kinematic degrees of indeterminacy, respectively, are

Beam PQ fixed at P (left) and hinged at Q (right), with an inclined load F applied between them at angle theta to the beamFθPQ
  1. (A)2 and 1
  2. (B)2 and 0
  3. (C)1 and 2
  4. (D)2 and 2

Answer: (A) 2 and 1 Official key: A

  1. Static indeterminacy = unknown reactions minus equations of equilibrium. The fixed support at P gives 3 reactions (horizontal, vertical, moment); the hinge at Q gives 2 (horizontal, vertical): .
  2. A plane beam has 3 equilibrium equations, so . The load is inclined, so the horizontal reactions are genuinely needed; they are not zero by inspection.
  3. Kinematic indeterminacy = number of unknown joint displacements. P is fixed: nothing moves. Q is hinged: both translations are held but the beam can rotate there, 1 unknown rotation.
  4. . Answer: (A) 2 and 1.

Trap: (B) treats the hinge as if it also stops rotation. Ignoring axial deformation does not change the count here, because the hinge already holds Q horizontally. (C) swaps the two numbers.

Where this shows up in industry

The kinematic count is the size of the stiffness matrix a program like STAAD.Pro or ETABS solves; the static count tells you how many redundants a hand check by the force method needs, which is why propped cantilevers are a standard hand-check case.

GATE 2023 · CE1 · Q.26MSQ · 1 markDeterminacy, trusses, frames, arches and cables

Which of three structures is unstable: a beam with two internal hinges and two pin-jointed trusses?

Consider the following three structures:

StructureDescription
IBeam with hinge support at A, roller at C, guided roller at E, and internal hinges at B and D
IIPin-jointed truss, with hinge support at A, and rollers at B and D
IIIPin-jointed truss, with hinge support at A and roller at C

Which of the following statements is/are TRUE?

Three structures. I: beam ABCDE, spans L, hinge support at A, roller at C, guided roller against a wall at E, internal hinges at B and D. II: square pin-jointed truss ABCD of side L with both diagonals, hinge support at top-left A on a wall, roller under B, roller against a wall at D. III: two-panel pin-jointed truss, top chord DEF and bottom chord ABC, verticals AD, BE and CF, both diagonals in the right panel only, hinge at A and roller at CStructure IABCDEinternal hinges at B and D (open circles)LLLLStructure IIADBCLLhinge at A, rollersat B and DStructure IIIDEFABCLLL
  1. (A)Structure I is unstable
  2. (B)Structure II is unstable
  3. (C)Structure III is unstable
  4. (D)All three structures are stable

Answer: (A, B, C) Official key: A, B, C

  1. Structure I: reactions 2 (A) + 1 (C) + 2 (guided roller E: horizontal force and moment) = 5, equations 3 + 2 hinge conditions = 5, so the count says determinate. But BCD sits on one roller: it can rotate about C while AB swings about A and DE slides up the guide without rotating. A mechanism: unstable.
  2. Structure II: , yet the reactions at A, the vertical one at B (same vertical line) and the horizontal one at D (same horizontal line) all pass through A. Nothing resists a moment about A: unstable.
  3. Structure III: , but the left panel ABED has no diagonal and folds like a parallelogram while the right panel has two. Unstable.
  4. Answer: (A, B, C); (D) is false.

Trap: trusting (or releases) alone. The count is necessary, not sufficient: always check for concurrent or parallel reactions and for a panel with too few members.

Where this shows up in industry

Analysis software flags exactly these cases as a singular stiffness matrix or a mechanism warning; engineers fix them by adding a brace in the open panel or moving a support so that the reactions are no longer concurrent.

GATE 2023 · CE1 · Q.54NAT · 2 marksDeterminacy, trusses, frames, arches and cables

Idealised six-panel bridge truss with 20 kN at each top joint: force in the diagonal U2L3

An idealised bridge truss is shown in the figure. The force in Member is ______ kN (round off to one decimal place).

Idealised bridge truss of six 3 m panels, 18 m span and 3 m deep: top chord U0 to U6 with a hinge at U0 and a roller at U6, bottom chord L1 to L5, verticals U1L1 to U5L5, end diagonals U0L1 and U6L5, diagonals U1L2 and U2L3 sloping down towards mid-span and U4L3 and U5L4 sloping down towards mid-span from the other side; 20 kN at each of U1 to U520 kN20 kN20 kN20 kN20 kNU0U1U2U3U4U5U6L1L2L3L4L56 @ 3 m = 18 m3 m

Answer: 14.1 kN (tension) Official key: 13.5 to 14.5

  1. Loads are symmetric: five 20 kN loads, so each support takes .
  2. Cut the panel between and : the section passes through , and . The two chords are horizontal, so only the diagonal can carry the vertical shear.
  3. Shear in the panel from the left part: upward.
  4. The diagonal runs 3 m across and 3 m down, at : , so .
  5. It pulls the left part down and to the right, away from : tension. Answer: 14.1 kN (a joint-by-joint solve of all 21 members gives the same).

Trap: stopping at the vertical component, 10 kN, or forgetting the load at (it sits on the left part of the cut), which gives kN.

Where this shows up in industry

Diagonals of Pratt and Howe bridge trusses are sized for panel shear in exactly this way; because the shear grows towards the supports, the end diagonals of a real girder bridge are visibly heavier than those near mid-span.

GATE 2024 · CE1 · Q.33NAT · 1 markDeterminacy, trusses, frames, arches and cables

Kinematic indeterminacy of a braced plane frame with fixed, hinge and roller supports, axial deformation neglected

The plane frame shown in the figure has fixed support at joint A, hinge support at joint F, and roller support at joint I. In the figure, A to I indicate joints of the frame.

If the axial deformations are neglected, the degree of kinematic indeterminacy is ________ (in integer).

Plane frame with fixed support A, hinge support F and roller support IABCDGEHFIRedrawn, not to scale

Answer: 9 Official key: 9 to 9

  1. Kinematic indeterminacy is the number of independent joint displacements: rotations plus translations. Neglecting axial deformation means no member changes length.
  2. Rotations: every rigid joint not held against rotation can turn: B, C, D, E, G and H, plus F (hinge support) and I (roller). That is ; only the fixed joint A cannot rotate.
  3. Translations: A and F cannot move. B is tied to A and F by two inextensible members in different directions (AB, BF), so it is held. In the same way E is held by BE and EF, H by EH and FH, I by FI and HI, C by BC and CE, and D by CD and DE.
  4. G hangs on DG alone: DG stops it moving horizontally but not vertically, so it has free translation.
  5. .
  6. Answer: 9.

Trap: the shortcut treats every member as removing one sway, but here the diagonals duplicate constraints that the other members already provide. Ignoring the free end G (its rotation and vertical movement) also gives 7.

Where this shows up in industry

Kinematic indeterminacy is the size of the stiffness matrix a frame program solves: STAAD.Pro or ETABS find exactly these joint displacements, and declaring members axially rigid shrinks the system in the same way.

GATE 2024 · CE1 · Q.49NAT · 2 marksDeterminacy, trusses, frames, arches and cables

Reaction at pin L of a 13-joint, 22-member plane truss with pins at A and L and a roller at K

The plane truss shown in the figure has 13 joints and 22 members. The truss is made of a homogeneous, prismatic, linearly elastic material. All members have identical axial rigidity. A to M indicate the joints of the truss. The truss has pin supports at joints A and L and roller support at joint K. The truss is subjected to a 10 kN vertically downward force at joint H and a 10 kN horizontal force in the rightward direction at joint B as shown.

(Figure NOT to scale)

The magnitude of the reaction (in kN) at the pin support L is _____________ (rounded off to 1 decimal place).

13-joint plane truss with pins at A and L and a roller at K10 kN10 kNABCDEFIGHJLKM2 m1 m1 m1 m1 m2 m1 m1 m1 m1 mRedrawn, not to scale

Answer: 7.5 kN Official key: 7.0 to 8.0

  1. Count: against , so the truss is indeterminate to degree . The redundant is internal (the square EFHG has both diagonals); the reactions are still statically determinate.
  2. Why: the truss is three rigid parts, ABCD (pinned at A), the middle part from D to J, and JKLM (pinned at L, roller at K), joined by pins at D and J. Three parts give 9 equations for 9 unknowns: five reactions and two pin forces.
  3. Middle part, moments about D: the 10 kN at H acts 3 m to the right of D and J is 4 m to the right on the same level, so the right part pushes up at J with .
  4. Right part: the roller at K presses against a vertical wall, so it gives a horizontal force only, and all the vertical force goes to L: . The pin force at J and both act 2 m above L, so moments about L make them cancel and .
  5. .
  6. Answer: 7.5 kN.

Trap: the 'identical axial rigidity' line suggests a stiffness analysis, but the reactions do not need one. Giving all of the 10 kN at H to L because H is nearer is also wrong: the left part carries of it through D.

Where this shows up in industry

Bridge and roof engineers make the same check before trusting software: when the reactions are statically determinate, bearing forces can be hand-checked even if member forces need a stiffness analysis because of redundant diagonals.

GATE 2025 · CE2 · Q.46MSQ · 2 marksDeterminacy, trusses, frames, arches and cables

Zero-force members of a truss with a loaded overhanging arm on a two-column tower

In the pin-jointed truss shown in the figure, the members that carry zero force are identified. Which of the following options is/are zero-force members?

Pin-jointed truss. A cantilevered arm: bottom chord A, C, E, G, I horizontal; sloping top chord A, B, D, F with verticals B-C, D-E, F-G, diagonals B-E and E-F, a 60 kN load down at B; F-H horizontal, H-I vertical, diagonal F-I. Below the arm a tower: verticals G-J-L and I-K-M, horizontals J-K and L-M, diagonals I-J and J-M; pin support at L, roller at M60 kNACEGIBDFHJKLMRedrawn, not to scale
  1. (A)BC
  2. (B)EG
  3. (C)FI
  4. (D)JK

Answer: (A) and (D) Official key: A;D

  1. Rule 1: at an unloaded joint with only two non-collinear members, both are zero. Rule 2: at an unloaded joint with three members, two collinear, the third is zero.
  2. Joint A has only AB and AC, not collinear, no load: AB = AC = 0.
  3. Joint C: AC (now zero) and CE are collinear, so BC = 0. Then CE = 0 too.
  4. Joint K: IK and KM are collinear (one vertical), so JK = 0.
  5. EG is not zero: joint B, with AB = BC = 0, sends the 60 kN through BD and BE; joint D (BD and DF collinear) makes DE = 0, so at E the force in BE must be balanced by EF and EG together. FI is not zero: at H (two members, unloaded) FH = HI = 0, which leaves FI as the diagonal carrying the arm's load from F down to I and the tower.
  6. Answer (A) and (D).

Trap: the 60 kN sits at B, so BC looks loaded; the load goes along the top chord and BE, not down BC. The same rules also zero FH, HI, IJ, JM and LM (with M on a roller), none of them offered.

Where this shows up in industry

Zero-force members are not spare: in a crane jib or transmission tower arm they brace the compression chords against buckling and take load the moment the wind or the hook load changes direction, which is why they stay in the design.

GATE 2026 · CE1 · Q.39MCQ · 2 marksDeterminacy, trusses, frames, arches and cables

Maximum bending moment in a portal frame on a hinge and a roller with 50 kN lateral and 90 kN beam loads

The plane frame has a hinge and a roller support, and is loaded as shown in the figure. Both the columns have same height.

What is the absolute value of the maximum bending moment (in kN-m) in the frame?

Portal frame ABCD: hinge support at A and roller support at D at the feet of two 3 m columns; beam BC is 4 m long with a 90 kN downward load at its middle, 2 m from B, and a 50 kN horizontal load acts to the right at joint B90 kN50 kN2 m2 m3 mABCDRedrawn, not to scale
  1. (A)165
  2. (B)150
  3. (C)240
  4. (D)195

Answer: (A) 165 Official key: A

  1. The roller at D gives only a vertical reaction ; the hinge at A gives and . The frame is determinate.
  2. : kN, acting to the left.
  3. Moments about A: , so kN and kN.
  4. Column AB carries the 50 kN base shear, so the moment at its top is kN m. Column CD has no horizontal force, so it has no moment and .
  5. Under the 90 kN load, from C: kN m. Check from B: kN m.
  6. Answer (A) 165 kN m, under the load.

Trap: 150 (B) is the column-top moment. Adding all 150 to the simply supported gives 240 (C), but the end moment falls linearly from 150 at B to zero at C, so only 75 of it acts at midspan.

Where this shows up in industry

Sheds and pipe racks are often built with one pinned base and one sliding base so that temperature movement does not lock in forces. The price is that one column takes all the lateral load, and its top moment then often governs the beam-to-column joint.

GATE 2026 · CE2 · Q.39MCQ · 2 marksDeterminacy, trusses, frames, arches and cables

Two-storey plane truss hinged at E and F, 40 kN horizontal at G and 20 kN at R: force in member JF

The plane truss shown in the figure is hinge-supported at E and F. The truss is subjected to vertical downward force at R and horizontal force at G.

(Figure not to scale)

The force (in kN) along with its nature in member JF is

Plane truss three storeys of joints: bottom row E T U V F, middle row G H I J K, top row L M N R S, 3 m panels and 3 m storeys; hinge supports at E and F; diagonals EH, HU, UJ, JF below and GM, MI, IR, RK above; verticals LG, GE, HT, NI, JV, SK, KF; 40 kN horizontal at G, 20 kN down at RETUVFGHIJKLMNRS40 kN20 kN3 m3 m3 m3 m3 m3 mRedrawn, not to scale
  1. (A) compression
  2. (B) tension
  3. (C) compression
  4. (D) tension

Answer: (A) compression Official key: A

  1. Cut the truss horizontally through the bottom storey, between the bottom row E-F and the middle row G-K. The cut members are the verticals GE, HT, JV, KF and the four diagonals EH, HU, UJ, JF, each at .
  2. Joints T and V each have two collinear chord members and a vertical, so HT and JV are zero. Vertical equilibrium at joints H, U and J then makes the four diagonal forces equal in size with alternating sign: .
  3. Horizontal equilibrium of the part above the cut: only the diagonals have horizontal components, so they carry the whole 40 kN storey shear: , so kN.
  4. The 40 kN pushes the upper part to the right, so the diagonals must push it back to the left: at J, member JF points down to the right, so it pushes, which is compression.
  5. Answer (A) kN compression (EH and UJ are in tension, HU and JF in compression).

Trap: taking the full vertical reaction at F, 25 kN, into JF gives , options (C) and (D). The two hinges make the truss once indeterminate, but the redundant thrust runs only along the straight bottom chord, so JF is found by statics.

Where this shows up in industry

Transmission towers and braced steel frames are checked storey by storey this way: the horizontal wind load above a level must pass through the bracing diagonals of the panel below it, so those members are sized for the storey shear rather than for the gravity loads.

GATE 2022 · CE2 · Q.46MSQ · 2 marksDeflections: energy, virtual work, moment-area, conjugate beam

Which statements on Castigliano's theorems, Betti's reciprocal theorem and the conjugate beam are correct

Which of the following statement(s) is/are correct?

  1. (A)If a linearly elastic structure is subjected to a set of loads, the partial derivative of the total strain energy with respect to the deflection at any point is equal to the load applied at that point.
  2. (B)If a linearly elastic structure is subjected to a set of loads, the partial derivative of the total strain energy with respect to the load at any point is equal to the deflection at that point.
  3. (C)If a structure is acted upon by two force system and , in equilibrium separately, the external virtual work done by a system of forces during the deformations caused by another system of forces is equal to the external virtual work done by the system during the deformation caused by the system.
  4. (D)The shear force in a conjugate beam loaded by the M/EI diagram of the real beam is equal to the corresponding deflection of the real beam.

Answer: (A, B, C) Official key: A, B, C

  1. (A) is Castigliano's first theorem, . True.
  2. (B) is Castigliano's second theorem, , valid for a linearly elastic structure. True. It is the basis of the unit-load and strain-energy deflection methods.
  3. (C) is Betti's reciprocal theorem (Maxwell's reciprocal theorem is its special case with two unit loads). True.
  4. (D) In the conjugate beam, the shear force equals the slope of the real beam and the bending moment equals the deflection. False.
  5. Answer: (A), (B) and (C).

Trap: swapping the two conjugate-beam results, the same way in a real beam. Integrating once gives slope (conjugate shear), twice gives deflection (conjugate moment).

Where this shows up in industry

Reciprocal theorems are why a structural model's flexibility and stiffness matrices are symmetric; engineers use Maxwell-Betti to get an influence line for a deflection by applying one unit load instead of moving it along the structure.

GATE 2022 · CE2 · Q.51NAT · 2 marksDeflections: energy, virtual work, moment-area, conjugate beam

Two cantilevers joined by a vertical spring: load at the centre of the lower beam that makes the spring force zero

The linearly elastic planar structure shown in the figure is acted upon by two vertical concentrated forces. The horizontal beams and are connected with the help of the vertical linear spring with spring constant kN/m. The fixed supports are provided at and . It is given that flexural rigidity kN-m2, kN, and m. Force is applied at the center of beam such that the force in the spring becomes zero.

The magnitude of force (in kN) is ______. (round off to the nearest integer)

Cantilever UV fixed at U, length 2a, flexural rigidity EI, load P down at the free end V; a vertical spring k joins V to W, the free end of cantilever WX fixed at X, length 2a, flexural rigidity 2EI, with load Q down at its centre, a from each endP2aEIUVkQaa2EIWX

Answer: 640 kN Official key: 620 to 660

  1. Zero spring force means the spring keeps its length, so and deflect down by the same amount. With no spring force each beam is a plain cantilever, and drops out.
  2. Tip of (length , , load at the tip): m.
  3. Tip of (length , , load at from ): deflection under the load plus slope there times the remaining : .
  4. , so 640 kN.

Trap: matching to the deflection under instead of at gives kN; using instead of for gives 320 kN. Both are outside the key.

Where this shows up in industry

Matching deflections at a connection is how engineers check transfer beams, hangers and props between floors: if two members must not share load, their free deflections at the link have to be equal, which is what the spring-force-zero condition expresses.

GATE 2023 · CE1 · Q.39MCQ · 2 marksDeflections: energy, virtual work, moment-area, conjugate beam

Wall-supported truss with a 30 degree inclined chord of three L members: vertical deflection of the loaded joint T

Consider the pin-jointed truss shown in the figure (not to scale). All members have the same axial rigidity, AE. Members QR, RS, and ST have the same length . Angles QBT, RCT, SDT are all . Angles BQT, CRT, DST are all . The joint T carries a vertical load P. The vertical deflection of joint T is . What is the value of ?

Pin-jointed truss: Q above B on a vertical line, Q pinned to a wall, B on a roller against the wall; inclined chord Q R S T, each part L long, 30 degrees from the vertical QB; bottom chord B C D T, with verticals RC and SD and diagonals BR and CS; angle at T is 60 degrees; vertical load P at TPQRSTBCD30°60°LLL
  1. (A)1.5
  2. (B)4.5
  3. (C)3.0
  4. (D)9.0

Answer: (B) 4.5 Official key: B

  1. Unit load method: with here, since the unit load sits where P does.
  2. Joint T: , so (tension); horizontally (compression).
  3. Joint D: SD is zero. Joint S: resolving along and across the chord gives , . Repeating at C and R, members RC, BR and QB are also zero, and .
  4. Inclined chord: . Bottom chord (each long): .
  5. : (B) 4.5.

Trap: taking the inclined members as carrying just P (ignoring the 30 degree tilt) gives for the chord, option (C). Only six of the eleven members carry force; spotting the five zero members first saves most of the work.

Where this shows up in industry

The same virtual-work sum is what frame software does for every load case; engineers still use it by hand to check the deflection of a cantilevered canopy or signage truss before trusting a model, because a wrong support condition shows up immediately.

GATE 2023 · CE2 · Q.16MCQ · 1 markDeflections: energy, virtual work, moment-area, conjugate beam

Mid-span deflection of a simply supported beam when the UDL is removed from one half of the span

When a simply-supported elastic beam of span and flexural rigidity ( is the modulus of elasticity and is the moment of inertia of the section) is loaded with a uniformly distributed load per unit length, the deflection at the mid-span is

If the load on one half of the span is now removed, the mid-span deflection ______.

  1. (A)reduces to
  2. (B)reduces to a value less than
  3. (C)reduces to a value greater than
  4. (D)remains unchanged at

Answer: (A) reduces to Official key: A

  1. Split the full UDL into the load on the left half and the load on the right half. By superposition (linear elastic beam), at mid-span.
  2. The beam is symmetric about mid-span, and the right-half load is the mirror image of the left-half load, so both give the same mid-span deflection: .
  3. With one half unloaded, : (A) reduces to .
  4. Check by the unit load method, with the half-span load: , and .

Trap: thinking of the largest deflection. With one half loaded it moves off mid-span towards the loaded half (to about ) and is 0.8 % larger than , which tempts (C). The question asks for the mid-span value, which is exactly half.

Where this shows up in industry

Superposition is how analysis software combines load cases. Designers use the same idea for pattern loading of floors and continuous beams, loading alternate spans or halves to find the worst deflection and moment.

GATE 2024 · CE2 · Q.49NAT · 2 marksDeflections: energy, virtual work, moment-area, conjugate beam

Deflection at Q of a 6 m cantilever whose outer half QR is rigid and carries 5 kN/m

For the 6 m long horizontal cantilever beam PQR shown in the figure, Q is the mid-point. Segment PQ of the beam has flexural rigidity whereas the segment QR has infinite flexural rigidity. Segment QR is subjected to uniformly distributed, vertically downward load of .

The magnitude of the vertical displacement (in mm) at point Q is ________ (rounded off to 3 decimal places).

Cantilever PQR, rigid segment QR loaded by 5 kN/mPQR5 kN/m3 m3 mEIrigid (EI = ∞)

Answer: 1.181 mm Official key: 1.176 to 1.186

  1. The rigid segment QR does not bend, so only PQ deforms. Replace the load on QR by its action at Q: a shear and a moment .
  2. PQ is then a 3 m cantilever with an end load and an end moment: .
  3. .
  4. , so 1.181 mm.

Trap: dropping the end moment gives 0.675 mm. The rigid segment matters for R, not Q: R drops a further , to 3.206 mm, and some candidates report that instead.

Where this shows up in industry

Rigid-link idealisations like this are how frame models treat deep transfer girders, beam-column joint zones and stiff end plates: they carry load and rotation through without bending, so all deflection comes from the flexible parts.

GATE 2025 · CE1 · Q.50NAT · 2 marksDeflections: energy, virtual work, moment-area, conjugate beam

Stepped simply supported beam (2EI then EI) with a couple M0 at A: second derivative of deflection at mid-AC

For the beam and loading shown in the figure, the second derivative of the deflection curve of the beam at the mid-point of AC is given by . The value of is ______ (rounded off to the nearest integer).

Simply supported beam AB of span 2L, pinned at A and on a roller at B; the half AC next to A has flexural rigidity 2EI and the half CB has EI; a clockwise couple M0 is applied at AM0ACB2EIEILL

Answer: Official key: 3 to 3

  1. The second derivative of the deflection is the curvature, .
  2. Reactions for a couple on a span : upward, downward. The beam is determinate, so the stepped stiffness does not change them.
  3. Moment from the left: , falling linearly from at A to at B.
  4. Mid-point of AC, : .
  5. That point is in the part: , so .

Trap: dividing by instead of gives , and taking the mid-span of AB (at C, moment ) gives 4. Read the rigidity of the segment where the point sits.

Where this shows up in industry

Curvature M/EI is the quantity a finite element beam model integrates for deflection, and it is what strain gauges on a bridge girder actually measure: the gauge strain divided by the distance from the neutral axis.

From GATE prep to a structural analysis and design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.