GATE Civil: Fluid Mechanics and Hydraulics (fluid statics, Bernoulli, pipe flow, dimensional analysis, critical flow, hydraulic jump, GVF), previous-year questions solved
Every fluid mechanics and hydraulics question from the ten official GATE Civil papers of 2022-2026: 44 questions (21 NAT, 17 MCQ, 6 MSQ) on hydrostatics, Bernoulli and momentum, pipe flow and drag, dimensional analysis, critical flow, hydraulic jumps and water surface profiles, each solved step by step and checked by a script against the official key. GATE 2027 adds mobile-bed channels, unsteady and rapidly varied flow, and sharp-crested weirs to Hydraulics.
Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 23 of 44 questions on this page
Dimension of dynamic viscosity in terms of mass, length and time
The dimension of dynamic viscosity is:
- (A)M L-1 T-1
- (B)M L-1 T-2
- (C)M L-2 T-2
- (D)M L0 T-1
Answer: (A) M L-1 T-1 Official key: A
- Newton's law of viscosity: , so .
- Shear stress is force per area: .
- Velocity gradient is velocity per length: .
- So , the unit Pa s or kg/(m s). Water at 20 °C has Pa s.
- Answer: (A).
Trap: option (B) is the dimension of shear stress itself, reached by forgetting to divide by the velocity gradient. Kinematic viscosity is and is not among the options.
Viscosity enters every pipe design through the Reynolds number, and water's viscosity halves between 10 and 50 degrees Celsius, which is why friction factors for hot-water and cold-water lines differ.
Absolute pressure in a pipe from an open manometer with oil (SG 0.8) over mercury (SG 13.6)
The pressure in a pipe at X is to be measured by an open manometer as shown in figure. Fluid A is oil with a specific gravity of 0.8 and Fluid B is mercury with a specific gravity of 13.6. The absolute pressure at X is ________ kN/m2 (round off to one decimal place).
[Assume density of water as 1000 kg/m3 and acceleration due to gravity as 9.81 m/s2 and atmospheric pressure as 101.3 kN/m2] [Note: Figure is not to scale]
Answer: 140.5 Official key: 140.0 to 141.0
- Start at the open end (atmospheric) and walk down to X, adding for every drop in level.
- Open mercury surface to the oil-mercury interface: down 0.25 m of mercury, kN/m².
- Interface to X: the oil goes up over the bend and back down, but only the net level matters. X is 0.75 m below the interface, so kN/m².
- kN/m² absolute (gauge 39.24 kN/m²).
- Answer: 140.5 kN/m²
Trap: X sits below the interface, so the oil column adds to the pressure. Subtracting it gives 128.8 kN/m², and leaving out the atmosphere gives the gauge value 39.2 kN/m².
U-tube and differential manometers are still the calibration reference for pressure transducers on pipelines and pump test rigs, and the same level-walk is how field engineers read piezometer boards.
Total pressure force on the side of a closed oil-and-water tank connected to an overhead reservoir
A 5 m × 5 m closed tank of 10 m height contains water and oil, and is connected to an overhead water reservoir as shown in the figure. Use and Specific gravity of oil = 0.8.
The total force (in kN) due to pressure on the side PQR of the tank is ____________ (rounded off to the nearest integer).
Answer: Official key: 5575 to 5585
- The water in the tank is joined to the reservoir by the pipe, so its pressure is set by the reservoir surface: the pipe leaves 2 m above the reservoir base (level with Q) and the surface is 8 m above the pipe, i.e. 10 m above Q and 16 m above P.
- Water layer: kPa and kPa.
- Oil layer: pressure falls going up through 4 m of oil, kPa, held by the closed lid.
- Pressure varies linearly in each layer, so force = mean pressure × area (width 5 m): QP: kN; RQ: kN.
- Answer: (key 5575 to 5585).
Trap: treating the tank as open, with zero pressure at R, gives kN; measuring the 8 m from Q instead of from the pipe gives kN.
Elevated service reservoirs pressurise ground-level sumps, pressure vessels and pipe networks in exactly this way; tank walls and lids are designed for the reservoir head, not for the depth of liquid inside, which is why a closed tank on a high-level supply needs a far stronger lid.
Shear stress against velocity gradient: identify the real solid, Bingham plastic, Newtonian and ideal fluid
The following figure shows a plot between shear stress and velocity gradient for materials/fluids P, Q, R, S, and T.
Which one of the following options is CORRECT?
- (A)P → Ideal Fluid; Q → Ideal Bingham plastic; R → Non-Newtonian fluid; S → Newtonian fluid
- (B)P → Real solid; Q → Ideal Bingham plastic; S → Newtonian fluid; T → Ideal Fluid
- (C)P → Ideal Fluid; Q → Ideal Bingham plastic; R → Non-Newtonian fluid; T → Real solid
- (D)P → Real solid; Q → Newtonian fluid; R → Ideal Bingham plastic; T → Ideal Fluid
Answer: (B) P → Real solid; Q → Ideal Bingham plastic; S → Newtonian fluid; T → Ideal Fluid Official key: B
- T lies on the velocity-gradient axis: it deforms at any rate with zero shear stress, i.e. zero viscosity, the ideal fluid.
- S is a straight line through the origin, with constant : a Newtonian fluid (water, air).
- Q is straight but starts at a stress on the axis: nothing flows until a yield stress is passed, then , an ideal Bingham plastic (fresh concrete, toothpaste).
- R starts at the origin with a falling slope: a shear-thinning non-Newtonian fluid.
- P hugs the stress axis: large stress, almost no rate of deformation, a real solid (an ideal solid would lie on the axis itself).
- Only (B) has every pairing right: (B).
Trap: (A) and (C) call P the ideal fluid; zero viscosity means zero shear stress, which is T. (D) calls Q Newtonian, but a Newtonian line passes through the origin.
Fresh concrete, cement grout and bentonite slurry are Bingham-type materials: pumping and tremie design for piles and diaphragm walls start from their yield stress and plastic viscosity, measured on site with rheometers or the slump-flow test.
6 m wide inclined gate hinged at P, 3 m by 4 m, shaft fails at 3924 kN m: maximum water depth h
The shaft of a 6 m wide gate in the figure will fail at a moment of 3924 kN.m about the hinge P. The maximum value of water depth h (in m) that the gate can hold is ________ (round off to the nearest integer).
Note:
Density of water = 1000 kg/m3
Acceleration due to gravity = 9.81 m/s2
Answer: Official key: 7 to 9
- The gate runs from P 3 m across and 4 m up, so its length is m and the depth falls by m per metre along it. At distance from P the depth is .
- Pressure acts normal to the gate, so its moment about P is .
- Integrate from 0 to 5: .
- and , so .
- , so 8 m (key 7 to 9). Check by components: the horizontal force on the 4 m projection gives kN m and the weight of water above the gate kN m, total 3924.
Trap: taking only the horizontal force on the vertical projection ignores the water resting on the sloping gate and gives m, outside the key.
Radial and flap gates on barrages and canal regulators are checked the same way: the hydrostatic thrust and its moment about the trunnion or hinge set the size of the pins, shafts and hoist, as laid out in IS 4623 for radial gates.
Horizontal hydrostatic force on a 0.5 m wide vertical gate holding 0.5 m of oil over 1.0 m of water
The cross section of a 0.5 m wide vertical gate holding water and oil is shown in the figure. The unit weights of water and oil are 10 kN/m3 and 7.5 kN/m3, respectively.
The horizontal hydrostatic force (in kN) acting on the vertical gate is _________ (rounded off to two decimal places).
Answer: Official key: 4.75 to 5.00
- Pressure grows linearly in each layer. At the oil-water interface: .
- The oil's weight sits on the water, so at the base: .
- Force from the oil layer (triangle): .
- Force from the water layer (trapezium): .
- Total: . Answer: (key range 4.75 to 5.00).
Trap: starting the water's pressure at zero at the interface, as if the oil were not there, gives ; treating the whole 1.5 m as water gives ; forgetting the 0.5 m width gives . All three are outside the key.
Layered pressure diagrams like this are used for oil-water separator walls at refineries, tank partitions and sluice gates in sedimentation basins, where a lighter liquid floats on water and the gate, its seals and hoist are sized from the total thrust and its line of action.
Efficiency of a 20 m/s water jet striking a series of radial plates on a wheel moving at 15 m/s
A jet of water having a velocity of 20 m/s strikes a series of plates fixed radially on a wheel revolving in the same direction as the jet at 15 m/s. What is the percentage efficiency of the plates? (round off to one decimal place)
- (A)37.5
- (B)66.7
- (C)50.0
- (D)88.9
Answer: (A) 37.5 Official key: A
- With a series of plates, some plate is always in the path, so the whole jet mass flow is used.
- Each kilogram leaves the flat plate with no velocity along the jet relative to the plate, so the force is , with relative velocity m/s.
- Work done per second: . Kinetic energy supplied per second: .
- Efficiency: .
- Answer: (A) 37.5 %
Trap: 50 % is the maximum of , reached at m/s, not at 15 m/s. Treating it as a single moving plate (mass flow ) gives only 9.4 %, which is not offered.
The same momentum balance sizes the buckets of Pelton turbines in hydropower plants, where curved buckets and a runner speed near half the jet speed push the efficiency close to 90 %.
Velocity field V = 3i + 5x j: is the fluid incompressible and is the flow rotational?
A flow velocity field for a fluid is represented by .
In the context of the fluid and the flow, which one of the following statements is CORRECT?
- (A)The fluid is incompressible and the flow is rotational.
- (B)The fluid is incompressible and the flow is irrotational.
- (C)The fluid is compressible and the flow is rotational.
- (D)The fluid is compressible and the flow is irrotational.
Answer: (A) The fluid is incompressible and the flow is rotational. Official key: A
- Components: and (steady, two-dimensional).
- Continuity: . The divergence is zero everywhere, which is the continuity equation of an incompressible fluid, so the field describes incompressible flow.
- Rotation: . It is not zero, so the flow is rotational; fluid elements spin at rad/s.
- Picture it: every particle moves right at 3 m/s while the upward velocity grows with , a shear flow, and shear flows carry vorticity.
- Answer: (A) incompressible and rotational.
Trap: the speed does not depend on and the streamlines are smooth, which tempts (B). Irrotational needs , and here .
The same two checks are the first sanity test engineers run on a CFD or PIV velocity field: zero divergence confirms mass is conserved, and the vorticity map shows where shear layers and eddies form, for example downstream of piers and gates.
Time for the water level in a 2 m x 1.5 m tank to fall from 5 m to 3.5 m through a 100 mm orifice
A 2 m × 1.5 m tank of 6 m height is provided with a 100 mm diameter orifice at the center of its base. The orifice is plugged and the tank is filled up to 5 m height. Consider the average value of discharge coefficient as 0.6 and acceleration due to gravity (g) as 10 m/s². After unplugging the orifice, the time (in seconds) taken for the water level to drop from 5 m to 3.5 m under free discharge condition is ____________ (rounded off to 2 decimal places).
Answer: Official key: 102.00 to 106.00
- Torricelli: the orifice discharges , and continuity gives .
- Separate and integrate from to : .
- , , .
- Numerator ; denominator .
- Answer: (key 102 to 106; a step-by-step time march of the same equation agrees).
Trap: dropping the 2 from the integral of gives s; ignoring (ideal orifice) gives s. The 6 m tank height plays no part.
Drain-down times of service reservoirs, sedimentation tanks and detention ponds are estimated with this same falling-head relation, for example to size the outlet orifice of a stormwater detention basin so it empties within the time set by the drainage design manual.
Conditions under which Bernoulli's equation can be applied in a fluid flow
For the Bernoulli's equation to be applicable in a fluid flow situation, which of the following conditions is/are to be satisfied:
- (A)Fluid should be frictionless
- (B)Fluid should be incompressible
- (C)Flow should be steady
- (D)Flow should be rotational
Answer: (A) and (B) and (C) Official key: A;B;C
- Bernoulli's equation constant is Euler's equation integrated along a streamline. Euler's equation has no viscous term, so the fluid must be frictionless (inviscid): (A).
- Integrating to needs constant density, so the fluid must be incompressible: (B).
- The local acceleration term must vanish for the integral to give a constant, so the flow must be steady: (C).
- Rotation is not a requirement. In rotational flow the constant holds along each streamline; only if the flow is irrotational is it the same constant everywhere. A forced vortex shows this: the total head grows with radius, yet it is constant on each circular streamline. So (D) is false.
- Answer: (A), (B) and (C).
Trap: ticking (D) because Bernoulli 'still works in rotational flow'. It works there along a streamline, but rotation is allowed, not required; the extra condition people quote is irrotational flow, for applying it across streamlines.
Venturi meters, orifice plates and Pitot tubes in water supply schemes all rely on Bernoulli's equation between two points on a streamline, with a discharge coefficient measured in calibration to absorb the friction the ideal equation leaves out.
Two-dimensional velocity field V = u x + v y: correct expressions for curl and divergence
Consider a velocity vector, in (x, y, z) coordinates given below. Pick one or more CORRECT statements(s) from the choices given below.
- (A)z-component of Curl of velocity;
- (B)z-component of Curl of velocity;
- (C)Divergence of velocity;
- (D)Divergence of velocity;
Answer: (A) and (C) Official key: A;C
- Curl is the cross product of with . With and nothing depending on , only the z-component survives: . (A) is true; (B) mixes in the normal strain rates and is false.
- Divergence is the dot product: each component differentiated along its own axis, . (C) is true; (D) is false.
- Check on a field where all four differ, , , at : curl , divergence ; (B) and (D) give other numbers.
- Answer: (A) and (C). Zero curl means irrotational flow; zero divergence means incompressible flow.
Trap: (D) adds the cross derivatives , which is twice the shear strain rate of a fluid element, not its rate of volume change.
CFD codes such as ANSYS Fluent and OpenFOAM enforce zero divergence in every cell for incompressible water flow and post-process the curl as vorticity to show eddies behind bridge piers and in pump intakes.
Discharge ratio of 20 cm and 10 cm parallel pipes of equal length between two reservoirs 5 m apart
Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm, as shown in the figure (not drawn to scale). When the difference in the water levels of the reservoirs is 5 m, the ratio of discharge in the larger diameter pipe to the discharge in the smaller diameter pipe is ____________. (round off to two decimal places)
(Consider only loss due to friction and neglect all other losses. Assume the friction factor to be the same for both the pipes)
Answer: Official key: 5.60 to 5.70
- Both pipes join the same two reservoirs, so each loses the full level difference: m in each.
- Darcy-Weisbach in terms of discharge: .
- With the same , and , the ratio is the same for both pipes, so .
- .
- Check with , m: and , ratio 5.657. Answer: .
Trap: assuming the same velocity in both pipes gives the area ratio 4. Velocity grows as here (3.13 vs 2.21 m/s), so the bigger pipe carries more than four times the flow.
Water supply engineers use the same D to the power 2.5 rule when they lay a parallel main beside an old one: doubling the diameter of the new pipe carries over five times the flow at the same head.
Stokes' law: drag on a 1.0 mm sphere relative to a 0.5 mm sphere of equal density settling in water
Two discrete spherical particles (P and Q) of equal mass density are independently released in water. Particle P and particle Q have diameters of 0.5 mm and 1.0 mm, respectively. Assume Stokes’ law is valid.
The drag force on particle Q will be________ times the drag force on particle P. (round off to the nearest integer)
Answer: Official key: 8 to 8
- Stokes' law: drag .
- Each particle settles at its terminal velocity, where drag balances the submerged weight: .
- Equal densities, so : Q settles times faster than P.
- Then , and . The same comes from the submerged weights, .
- Check with , Pa s: m/s, m/s. Answer: .
Trap: using the same velocity for both gives a ratio of 2 (drag proportional to ); using only the velocity ratio gives 4. Strictly, Q's Reynolds number here is about 899, beyond Stokes' range, which is why the question tells you to assume it.
Grit chambers and settling tanks in water and sewage treatment are designed from Stokes settling velocities, and the d squared law is why fine silt below about 0.01 mm hardly settles without coagulation.
True statements: turbulent boundary layer growth, swapped source flow, curved surface force, momentum factor
Which of the following statements is/are TRUE?
- (A)The thickness of a turbulent boundary layer on a flat plate kept parallel to the flow direction is proportional to the square root of the distance from the leading edge
- (B)If the streamlines and equipotential lines of a source are interchanged with each other, the resulting flow will be a sink
- (C)For a curved surface immersed in a stationary liquid, the vertical component of the force on the curved surface is equal to the weight of the liquid above it
- (D)For flow through circular pipes, the momentum correction factor for laminar flow is larger than that for turbulent flow
Answer: (C), (D) Official key: C, D
- A false. is the laminar (Blasius) result. A turbulent layer follows , so (computed exponent 0.80).
- B false. A source has , . Swapping gives , whose velocity is , : a free vortex, not a sink.
- C true. The vertical force on a curved surface equals the weight of the liquid (real or imaginary) vertically above it up to the free surface.
- D true. is 1.333 for the laminar parabola and 1.020 for the turbulent 1/7 power law.
- Answer: (C), (D)
Trap: picking A from memory of the laminar boundary layer, or reading B as a sign flip; reversing a source into a sink would mean changing the sign of , not swapping and .
Boundary layer growth sets skin-friction drag on ship hulls and the velocity profiles assumed in pipe and channel flow meters; the momentum factor enters every force calculation on bends and nozzles.
Diameter of a smoother replacement pipeline (f = 0.01 vs 0.04) for the same flow and head loss
A 500 m long water distribution pipeline P with diameter 1.0 m, is used to convey 0.1 m³/s of flow. A new pipeline Q, with the same length and flow rate, is to replace P. The friction factors for P and Q are 0.04 and 0.01, respectively. The diameter of the pipeline Q (in meters) is ____________ (rounded off to 2 decimal places).
Answer: Official key: 0.70 to 0.80
- Darcy-Weisbach with : .
- The replacement must carry the same over the same with the same head loss, so must stay the same: .
- m.
- Check: both pipes lose m of head over 500 m.
- Answer: (key 0.70 to 0.80).
Trap: inverting the ratio gives m, a bigger pipe for a smoother wall, which cannot be right; and treating as proportional to gives m.
Water utilities use this trade-off when relining or replacing old cast iron mains with ductile iron or HDPE: a smoother pipe carries the same demand at a smaller diameter, which is checked in network software such as EPANET or WaterGEMS before the size is fixed.
Pipes A (2 m, 100 m) and B (1 m, 200 m) in series, f = 0.01: ratio of head loss in B to head loss in A
Consider steady flow of water in the series pipe system shown below, with specified discharge. The diameters of Pipes A and B are 2 m and 1 m, respectively. The lengths of pipes A and B are 100 m and 200 m, respectively. Assume the Darcy-Weisbach friction coefficient, f as 0.01 for both the pipes.
The ratio of head loss in Pipe-B to the head loss in Pipe-A is ______ (round off to the nearest integer).
Answer: Official key: 64 to 64
- In series the same discharge passes through both pipes.
- Darcy-Weisbach: with , so , proportional to when and are fixed.
- .
- Ratio = 64 (key 64 to 64). Halving the diameter quadruples the velocity and raises the loss per metre 32 times.
Trap: assuming the same velocity in both pipes gives , and squaring the velocity ratio but forgetting the in Darcy-Weisbach gives ; the loss goes as the fifth power of diameter.
This fifth-power rule is why water supply designers in tools like EPANET or the CPHEEO manual approach pick pipe diameters with care: one size smaller raises friction loss several times and with it the pumping energy bill over the life of the main.
Two long parallel pipes of 600 mm and 400 mm diameter between two reservoirs: ratio of their flow rates
Two reservoirs having different water levels are connected by two long parallel pipelines of same length and same material but having diameters of 600 mm and 400 mm. Using Darcy-Weisbach equation, the ratio of flowrate of water in the bigger diameter pipe to that in the smaller diameter pipe is
- (A)0.54
- (B)1.22
- (C)1.84
- (D)2.76
Answer: (D) 2.76 Official key: D
- Both pipes run between the same two water surfaces, so each loses the same head . They are long, so minor losses are negligible, and the same material is read as the same friction factor .
- Darcy-Weisbach in terms of discharge: .
- With , and equal, , so .
- .
- Answer: (D) 2.76 (official key: D).
Trap: equal head loss gives , and the velocity ratio is option (B). The question asks for the flow rate, which also scales with the area, : .
Water supply engineers lay a second, parallel main beside an old one to raise capacity; because flow scales with the diameter to the power 2.5, a 400 mm duplicate beside a 600 mm main adds only about 36 % to the original flow at the same head.
Laminar flow in a 5 cm radius pipe with a 2 m/s maximum velocity: velocity 2.5 cm from the axis
In a laminar flow of a Newtonian fluid through a circular pipe of radius 5 cm, the maximum velocity is found to be 2 m/s. The velocity (in m/s) at a radial distance of 2.50 cm from the axis of the pipe is
- (A)1.00
- (B)1.25
- (C)1.50
- (D)1.75
Answer: (C) 1.50 Official key: C
- Fully developed laminar (Hagen-Poiseuille) flow has a parabolic profile, zero at the wall and largest on the axis: .
- Here , so .
- .
- Answer: (C) 1.50 (official key: C).
Trap: a linear fall from the axis to the wall, , is option (A). The shear stress varies linearly with in a pipe; the velocity, its integral, varies with . The mean velocity is .
Laminar pipe flow matters in practice for viscous fluids: oil and bitumen lines, hydraulic control tubing and slow chemical dosing lines are sized with Hagen-Poiseuille, where the head loss is proportional to velocity and not to its square.
Operating head of a pump with H = 140 - 9000 Q2 lifting 35 m through a 2 km, 250 mm pipe (f = 0.04)
A centrifugal pump is delivering water from an underground tank to an overhead reservoir against a static head of 35 m through a 2 km long, 250 mm diameter pipe. The head-discharge characteristic of the pump is given by
where is the head (in m) generated by the pump and is the discharge (in m3/s) of the pump.
Neglecting all minor losses, the head (in m) generated by the pump is ______ (rounded off to the nearest integer).
Use: Darcy-Weisbach friction factor f = 0.04
Acceleration due to gravity = 9.81 m/s2
Answer: Official key: 78 to 82
- The pump runs where its head equals the head the pipe system needs: static lift plus friction loss.
- Friction loss in terms of : .
- System curve: . Set it equal to the pump curve: .
- , so (, ).
- . Answer: (key range 78 to 82).
Trap: leaving out the 35 m static head gives ; using with as if it were the Fanning factor gives . Both are outside the key.
Every pumping main for a water supply scheme or high-rise building is checked this way: the manufacturer's head-discharge curve is overlaid on the system curve to find the duty point, and the pump is chosen so that point sits near its best-efficiency flow.
Match viscosity, gravity, compressibility and pressure with the Reynolds, Froude, Mach and Euler numbers
With respect to fluid flow, match the following in Column X with Column Y:
| Column X | Column Y |
|---|---|
| (P) Viscosity | (I) Mach number |
| (Q) Gravity | (II) Reynolds number |
| (R) Compressibility | (III) Euler number |
| (S) Pressure | (IV) Froude number |
Which one of the following combinations is correct?
- (A)(P) – (II), (Q) – (IV), (R) – (I), (S) – (III)
- (B)(P) – (III), (Q) – (IV), (R) – (I), (S) – (II)
- (C)(P) – (IV), (Q) – (II), (R) – (I), (S) – (III)
- (D)(P) – (II), (Q) – (IV), (R) – (III), (S) – (I)
Answer: (A) (P) – (II), (Q) – (IV), (R) – (I), (S) – (III) Official key: A
- Each of these numbers compares the inertia force with one other force, so each force pairs with the number that contains its property.
- Viscosity: , inertia over viscous force. (P)-(II).
- Gravity: , the square root of inertia over gravity force. (Q)-(IV).
- Compressibility: with , so is inertia over elastic force, being the bulk modulus. (R)-(I).
- Pressure: , pressure force over inertia. (S)-(III).
- Only option (A) has all four. Answer: (A).
Trap: option (D) swaps Mach and Euler. Mach carries the bulk modulus (compressibility); Euler carries a pressure difference.
Hydraulic model studies at CWPRS Pune scale spillways and river reaches by Froude similarity and pipe and pump tests by Reynolds similarity, because a small model can usually match only one force ratio of the prototype.
River discharge by the velocity-area method from depths and point velocities in seven 1.5 m segments
The cross-section of a small river is sub-divided into seven segments of width 1.5 m each. The average depth, and velocity at different depths were measured during a field campaign at the middle of each segment width. The discharge computed by the velocity area method for the given data is ________ m3/s (round off to one decimal place).
| Segment | Average depth D (m) | v at 0.2D (m/s) | v at 0.6D (m/s) | v at 0.8D (m/s) |
|---|---|---|---|---|
| 1 | 0.40 | -- | 0.40 | -- |
| 2 | 0.70 | 0.76 | -- | 0.70 |
| 3 | 1.20 | 1.19 | -- | 1.13 |
| 4 | 1.40 | 1.25 | -- | 1.10 |
| 5 | 1.10 | 1.13 | -- | 1.09 |
| 6 | 0.80 | 0.69 | -- | 0.65 |
| 7 | 0.45 | -- | 0.42 | -- |
(-- means no reading was taken at that depth.)
Answer: 8.5 Official key: 8.4 to 8.6
- Mean velocity in a vertical: a single reading at 0.6D in shallow water (segments 1 and 7), otherwise the average of the 0.2D and 0.8D readings.
- Segment means (m/s): 0.400, 0.730, 1.160, 1.175, 1.110, 0.670, 0.420.
- Segment discharge (m³/s): 0.240, 0.766, 2.088, 2.467, 1.831, 0.804, 0.284.
- Total: m³/s over a flow area of 9.07 m².
- Answer: 8.5 m³/s
Trap: using only the 0.2D readings gives 8.78 m³/s and only the 0.8D readings 8.18 m³/s, both outside the key; the velocity profile is roughly logarithmic, so neither point alone is the mean.
Central Water Commission gauging sites still measure river flow this way with current meters or ADCPs, and the discharges calibrate the stage-discharge rating curves used in flood forecasting.
Which combination of velocity, length scale and gravity is dimensionless
For a flowing fluid, a dimensionless combination of velocity (), length scale (), and acceleration due to gravity () would be
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Write the dimensions: , , . No mass appears, so only and must cancel.
- (A): , dimensionless.
- (B): . (C): . (D): .
- Answer (A). Its square root, , is the Froude number: inertia force over gravity force, the group that governs open channels, spillways and waves.
Trap: (D) looks like the inverse of the Froude group, but sits in the denominator next to instead of beside ; always check the powers of , which only and can cancel.
Physical models of spillways, stilling basins and river reaches at labs such as CWPRS Pune are built to Froude similarity, so a 1:50 model runs at the square root of 1/50 of the prototype velocity and its discharges scale by 50 to the power 2.5.
Drag on a sphere from viscosity, density, velocity and diameter: which groups are non-dimensional
The drag force, on a sphere due to a fluid flowing past the sphere is a function of viscosity, , the mass density, , the velocity of flow, , and the diameter of the sphere, .
Pick the relevant (one or more) non-dimensional parameter(s) pertaining to the above process from the following list.
- (A)
- (B)
- (C)
- (D)
Answer: (A) and (C) Official key: A;C
- Five variables () and three dimensions () give pi groups (Buckingham).
- Dimensions: , , , , .
- (A): , the same as , so (A) is dimensionless: the drag coefficient group. True.
- (C): : the Reynolds number. True.
- (B) and (D) both work out to , not dimensionless.
- Answer: (A) and (C), so .
Trap: (B) looks like the drag coefficient at a glance, but the density has moved to the numerator; and (D) is not the inverse Reynolds number, which would be .
The drag-coefficient-versus-Reynolds-number curve that comes out of this analysis is used to size grit chambers and settling tanks, and to work out wind and current loads on bridge piers, chimneys and offshore members.