GATE Civil: Engineering Mechanics and Solid Mechanics (SFD and BMD, stresses, torsion, Mohr's circle, buckling), previous-year questions solved

Every engineering mechanics and solid mechanics question from the ten official GATE Civil papers of 2022-2026: 36 questions (11 NAT, 22 MCQ, 3 MSQ) on forces and friction, shear force and bending moment diagrams, axial and thermal stresses, bending and shear stresses, torsion, stress transformation and column buckling, each solved step by step and checked by a script against the official key. GATE 2027 keeps all of these and drops only the free vibration of single-degree-of-freedom systems.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 10 of 36 questions on this page

GATE 2022 · CE1 · Q.37MCQ · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Axial force, shear and bending moment at 45 degrees in a semicircular bar fixed at one end and loaded at the other

A semi-circular bar of radius m, in a vertical plane, is fixed at the end G, as shown in the figure. A horizontal load of magnitude kN is applied at the end H. The magnitude of the axial force, shear force, and bending moment at point Q for , respectively, are

Semi-circular bar of radius R in a vertical plane, centre O, fixed at the right end G. A horizontal load P acts outwards (to the left) at the free left end H, along the diameter H-O-G. Point Q is on the bar where the radius OQ makes angle theta with OHRθQPHOG
  1. (A) kN, kN, and kNm
  2. (B) kN, kN, and 0 kNm
  3. (C)0 kN, kN, and kNm
  4. (D) kN, 0 kN, and kNm

Answer: (A) kN, kN, and kNm Official key: A

  1. Cut the bar at Q and keep the free part HQ, so no support reaction is needed. Measured from O, Q is to the left and above the line H-O-G.
  2. The only force on HQ is , horizontal, along the line H-O. Its lever arm about Q is the height of Q above that line: kNm.
  3. At Q the bar's axis is perpendicular to the radius OQ, so it makes 45° with the horizontal. Axial force kN.
  4. The shear force is the component along the radius: kN.
  5. Answer: (A).

Trap: (B) takes moments about O. The line of action of passes through O, so the moment there is zero, but Q sits above that line. (C) and (D) drop one component; at 45° the axial and shear components are equal.

Where this shows up in industry

Curved members such as arch ribs, crane hooks and pipe bends carry axial force, shear and bending together at every section. Frame-analysis programs report all three along a curved member, and the section is checked for the combination, not for the moment alone.

GATE 2022 · CE1 · Q.46MSQ · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Does a 1 m by 2 m block of 25 kN slide or overturn under a horizontal push at its top, with friction 0.3?

A horizontal force of kN is applied to a homogeneous body of weight 25 kN, as shown in the figure. The coefficient of friction between the body and the floor is 0.3. Which of the following statement(s) is/are correct?

Homogeneous rectangular block 1 m wide and 2 m high, weight 25 kN, standing on the floor; a horizontal force P acts to the left at its top right cornerP1 m2 m25 kN
  1. (A)The motion of the body will occur by overturning.
  2. (B)Sliding of the body never occurs.
  3. (C)No motion occurs for kN.
  4. (D)The motion of the body will occur by sliding only.

Answer: (A, C), or (A, B, C) Official key: A, C OR A, B, C

  1. Sliding starts when exceeds the limiting friction: kN.
  2. Overturning is about the bottom corner on the far side from . acts 2 m above it and the weight acts 0.5 m (half the width) from it: , so kN.
  3. : as grows, the block tips at 6.25 kN while friction can still hold it. Motion is by overturning, so (A) is true and (D) is false.
  4. Below 6.25 kN nothing moves, so (C), no motion for kN, is true.
  5. (B) is true for the first motion, but once the block rocks onto its corner a larger push could also make it slip, so "never" is debatable. The official key accepts both sets: (A, C), or (A, B, C).

Trap: using the full 1 m width as the weight's lever arm gives kN, more than 7.5 kN, and wrongly points to sliding first.

Where this shows up in industry

Retaining walls, gravity dams and tall equipment bolted to a slab are checked for both sliding and overturning, and the lower of the two loads governs. Designers widen the base when overturning controls and add a shear key or more weight when sliding does.

GATE 2022 · CE2 · Q.37MCQ · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Natural frequency and period of an undamped spring-mass system when the stiffness is doubled and the mass halved

An undamped spring-mass system with mass and spring stiffness is shown in the figure. The natural frequency and natural period of this system are rad/s and s, respectively. If the stiffness of the spring is doubled and the mass is halved, then the natural frequency and the natural period of the modified system, respectively, are

Mass m hanging from a fixed support by a spring of stiffness kmk
  1. (A) rad/s and s
  2. (B) rad/s and s
  3. (C) rad/s and s
  4. (D) rad/s and s

Answer: (A) rad/s and s Official key: A

  1. For an undamped single-degree-of-freedom system, and .
  2. New system: , , so .
  3. , and the period falls in the same ratio: .
  4. Answer: (A) rad/s and s.

Trap: forgetting the square root turns the factor 4 on into and , option (C). Gravity does not enter: hanging the mass only shifts the equilibrium position, not the frequency.

Where this shows up in industry

The same ratio governs earthquake design: IS 1893 spectra read the force from the natural period, so a stiffer frame or a lighter roof shortens the period by the square root of the change, not in direct proportion.

GATE 2022 · CE2 · Q.52NAT · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Uniform rod against a frictionless wall on a rough floor (height 4 m, base 3 m): minimum coefficient of friction

A uniform rod of weight shown in the figure rests against a frictionless vertical wall at the point and a rough horizontal surface at point . It is given that kN, m and m.

The minimum coefficient of static friction that is required at the point to hold the rod in equilibrium is ______. (round off to three decimal places)

Uniform rod KJ leaning with its top K on a frictionless vertical wall at height a and its foot J on a rough floor a horizontal distance b from the wallKJab

Answer: 0.375 Official key: 0.350 to 0.400

  1. Forces on the rod: weight at its middle, a horizontal normal reaction from the smooth wall, and at a vertical reaction and a friction force towards the wall.
  2. Vertical equilibrium: kN. Horizontal equilibrium: .
  3. Moments about : the weight acts m from horizontally, acts m above it. , so kN.
  4. 0.375, i.e. .

Trap: putting the weight at the foot-to-wall distance instead of gives 0.75; swapping and gives 0.667. Both fall outside the key.

Where this shows up in industry

Ladder safety rules come from this result: a ladder set at about 4 vertical to 1 horizontal needs a friction coefficient of only b/2a = 0.125 at the foot, while a flatter ladder quickly needs more grip than a smooth floor can give.

GATE 2023 · CE1 · Q.55NAT · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Moment of inertia of a T-shaped girder section (40 x 10 cm flange, 20 x 50 cm web) about its centroidal axis

The cross-section of a girder is shown in the figure (not to scale). The section is symmetric about a vertical axis (Y-Y). The moment of inertia of the section about the horizontal axis (X-X) passing through the centroid is ______ cm4 (round off to nearest integer).

T-shaped girder section, symmetric about the vertical axis Y-Y: flange 40 cm wide and 10 cm deep on top of a web 20 cm wide and 50 cm deep; X-X is the horizontal axis through the centroidYYXX40 cm10 cm50 cm20 cm

Answer: Official key: 464000 to 472000

  1. Split the T into the flange (, area , centroid 5 cm from the top) and the web (, area , centroid 35 cm from the top).
  2. Centroid from the top: .
  3. Flange: .
  4. Web: .
  5. 468810 cm4.

Trap: adding only the two own-axis terms gives 211667 cm4, less than half the answer. The parallel-axis terms are the larger part here because the flange sits far from the centroid.

Where this shows up in industry

Every bending check of a T-beam, from a precast bridge girder to a slab acting with its supporting beam, starts with this centroid and second moment of area; design software computes it, but engineers still verify it by hand for unusual sections.

GATE 2023 · CE2 · Q.53NAT · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Vertical reaction at the hinge of a 6 m beam with a 500 N inclined load and an eccentric 100 N horizontal load

A beam is subjected to a system of coplanar forces as shown in the figure. The magnitude of vertical reaction at Support P is ______ N (round off to one decimal place).

Beam PQ, hinged at P and on a roller at Q, 6 m span: a 500 N force inclined at 60 degrees to the beam pushes down at 2.0 m from P; a 200 N force acts upward at 3.5 m; at 4.5 m a 0.5 m tall vertical post carries a 100 N horizontal force to the right; spacing 2.0, 1.5, 1.0 and 1.5 m500 N60°200 N100 N0.5 mPQ2.0 m1.5 m1.0 m1.5 m

Answer: 197.0 N Official key: 195.0 to 200.0

  1. P is a hinge (vertical and horizontal reactions) and Q a roller (vertical only); span m.
  2. The 500 N force makes with the beam: vertical component N downward at 2.0 m from P; the horizontal N goes to the hinge.
  3. The 100 N horizontal force acts 0.5 m above the beam axis at 4.5 m from P. Moved to the axis it becomes 100 N plus a clockwise couple of N.m.
  4. Moments about Q, clockwise = anticlockwise: .
  5. 197.0 N upward. Check: N, and moments about P balance.

Trap: dropping the couple of the eccentric 100 N force gives 205.3 N, giving it the wrong sense gives 213.7 N, and using as the vertical component gives 75.0 N, all outside the key.

Where this shows up in industry

Every beam check starts like this: resolve inclined loads, replace an eccentric load by a force and a couple, and take moments about a support. Engineers verify the reactions STAAD.Pro or ETABS report with exactly this hand calculation.

GATE 2023 · CE2 · Q.57NAT · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Horizontal force at pin P between the arm PQ and post RS of a bracket frame with an inclined strut TU

An idealised frame supports a load as shown in the figure. The horizontal component of the force transferred from the horizontal member PQ to the vertical member RS at P is ______ N (round off to one decimal place).

Bracket frame: vertical member RS pinned at its base R and held horizontally by a roller at the top S; horizontal member PQ pinned to RS at P, 0.3 m below S; a strut pinned at T, 1.0 m below P, and at U, 1.2 m along PQ; Q is 0.6 m beyond U and carries a 10 N downward load; T is 1.0 m above R10 NSPUQTR1.2 m0.6 m0.3 m1.0 m1.0 m

Answer: 18.0 N Official key: 17.5 to 18.5

  1. TU is pinned at both ends and loaded only there, so it is a two-force member: its force acts along TU, which rises 1.0 m over 1.2 m.
  2. Free body PQ (pins at P and U, 10 N at Q). Moments about P: , so the strut pushes PQ up at U with N.
  3. Along the strut, horizontal : vertical , so N, pushing U to the right; TU is in compression with 23.43 N.
  4. Equilibrium of PQ: the pin at P pulls PQ left with 18 N and down with N.
  5. By action and reaction, PQ pushes RS at P with 18.0 N horizontally (to the right), plus 5 N upward.

Trap: inverting the strut slope () gives 12.5 N, and taking moments with the 0.6 m overhang instead of the full 1.8 m gives 6.0 N. Both are outside the key.

Where this shows up in industry

Wall brackets, crane jibs and signboard supports are frames of this kind. Spotting the diagonal strut as a two-force member lets an engineer size it, and the pins at P and T, before any software model exists.

GATE 2024 · CE2 · Q.16MCQ · 1 markEngineering mechanics: forces, friction, centroids and vibration

Rigid beam on two springs, 3 kN load 1 m from P: what spring stiffness at Q keeps the beam from rotating?

A 3 m long, horizontal, rigid, uniform beam PQ has negligible mass. The beam is subjected to a 3 kN concentrated vertically downward force at 1 m from P, as shown in the figure. The beam is resting on vertical linear springs at the ends P and Q. For the spring at the end P, the spring constant .

If the beam DOES NOT rotate under the application of the force and displaces only vertically, the value of the spring constant (in kN/m) for the spring at the end Q is

Rigid beam PQ on two springs with a 3 kN load 1 m from P3 kNPQKPKQ1 m2 m
  1. (A)150
  2. (B)100
  3. (C)50
  4. (D)200

Answer: (C) 50 Official key: C

  1. Statics first. Moments about Q: , so ; vertical balance gives .
  2. No rotation means both ends move down by the same amount .
  3. Spring at P: (20 mm).
  4. Spring at Q must give over the same : .
  5. Answer: (C) 50. The stiffer spring sits nearer the load, in the same ratio as the reactions.

Trap: (D) 200 inverts the ratio by reasoning that the far spring must be stiffer; (B) 100 makes the springs equal, which tilts the beam because they carry unequal loads.

Where this shows up in industry

Machine foundations and bridge bearings are sized this way: mounts under an off-centre load get stiffnesses proportional to their share of the load so that the equipment settles evenly instead of tilting.

GATE 2024 · CE2 · Q.37MCQ · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Natural frequency of a mass hung at the mid-span of a simply supported beam of span 2l with a spring k above

A linearly elastic beam of length with flexural rigidity has negligible mass. A massless spring with a spring constant and a rigid block of mass are attached to the beam as shown in the figure.

The natural frequency of this system is

Beam of span 2l with a spring k above and a mass m below its mid-spankmll
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Stiffness of a simply supported beam at mid-span: with span , so .
  2. The spring connects the same mid-span point to a fixed support. When the mass moves down by , the beam and the spring both deflect by and both push back: they act in parallel.
  3. .
  4. .
  5. Answer: (A).

Trap: (B) uses , forgetting that the span is ; (C) combines the spring and beam in series, which would be right only if the mass hung from the spring and the spring from the beam.

Where this shows up in industry

Footbridges and floors that bounce under walking are checked against a minimum natural frequency; adding stiffness in parallel (a prop, a tuned support) raises it, which is why retrofits often add supports rather than mass. GATE 2027 drops this topic.

GATE 2026 · CE1 · Q.50NAT · 2 marksEngineering mechanics: forces, friction, centroids and vibration

Two blocks joined by a rigid rod against a wall and a floor: friction coefficient when slip impends at 45 degrees

Two identical blocks A and B are connected by a rigid rod. The blocks rest against vertical and horizontal planes, as shown in the figure. The coefficient of static friction at the vertical and horizontal planes is the same. If the sliding impends when , the value of the coefficient of static friction is ______ (rounded off to two decimal places).

Block A rests against a vertical wall and block B, identical, rests on the horizontal floor; a rigid rod joins their centres and makes an angle theta with the horizontal, sloping down from A to BθAB

Answer: 0.41 Official key: 0.39 to 0.44

  1. Take the rod as light and pinned at the block centres, so it carries only an axial compression at to the horizontal. At impending slip A moves down the wall and B moves away from it, so friction acts up on A and towards the wall on B. Each block weighs .
  2. Block A: and .
  3. Block B: and .
  4. At write . From A, ; from B, .
  5. Equate: , so and .
  6. Answer 0.41.

Trap: leaving out the friction at the wall gives , outside the key (0.39 to 0.44). The wall friction carries part of the weight of A and lowers the friction needed at the floor.

Where this shows up in industry

The same balance sets the safe angle of a ladder against a wall and of the wedges and props used to strike formwork: friction at both contacts decides the flattest angle that still holds, which is why ladder rules ask for about 75 degrees, one out for every four up.

From GATE prep to a structural design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.