GATE Civil: Transportation Engineering (highway geometric design, pavements, bituminous mixes, traffic, railway and airport), previous-year questions solved

Every transportation engineering question from the ten official GATE Civil papers of 2022-2026: 64 questions (25 NAT, 27 MCQ, 12 MSQ) on highway geometric design, railway and airport engineering, highway materials and bituminous mixes, pavement design and traffic engineering, each solved step by step and checked by a script against the official key. GATE 2027 adds four-step travel demand modelling and level of service to the syllabus.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 36 of 64 questions on this page

GATE 2022 · CE1 · Q.28MSQ · 1 markHighway geometric design

Which measures reduce the radius of a horizontal curve in a region with limited space?

A horizontal curve is to be designed in a region with limited space. Which of the following measure(s) can be used to decrease the radius of curvature?

  1. (A)Decrease the design speed.
  2. (B)Increase the superelevation.
  3. (C)Increase the design speed.
  4. (D)Restrict vehicles with higher weight from using the facility.

Answer: (A, B) Official key: A, B

  1. Equilibrium of a vehicle on a banked curve gives the minimum radius , where is the superelevation and the side friction factor.
  2. Lower gives a smaller (A). Example with , : 80 km/h needs m, 65 km/h only 151 m.
  3. Larger gives a smaller (B): at 80 km/h with , m.
  4. Raising the speed (C) increases . Vehicle mass appears on both sides ( against ) and cancels, so banning heavy vehicles (D) changes nothing.
  5. Answer: (A) and (B).

Trap: ticking (D) because heavy trucks feel unsafe on sharp curves. Their problem is overturning and load shift, not the radius formula, which has no mass in it.

Where this shows up in industry

IRC:73 caps superelevation at 7 percent on plain and rolling terrain and 10 percent on hill roads not bound by snow, with a side friction factor of 0.15, so on tight hill alignments engineers lower the design speed to fit a smaller radius.

GATE 2022 · CE2 · Q.62NAT · 2 marksHighway geometric design

Parabolic crest curve between +1.0 % and -2.0 % grades for 200 m stopping sight distance: minimum length

A parabolic vertical crest curve connects two road segments with grades +1.0% and −2.0%. If a 200 m stopping sight distance is needed for a driver at a height of 1.2 m to avoid an obstacle of height 0.15 m, then the minimum curve length should be ______ m. (round off to the nearest integer)

Answer: 273 m Official key: 270 to 275

  1. Deviation angle: .
  2. Assume the curve is longer than the sight distance (): with m and m.
  3. .
  4. m, which is more than 200 m, so the assumption holds: 273 m.

Trap: the formula, , gives 253 m, but that result is only valid if was true, and 273 m > 200 m says it is not. Taking the deviation as gives 91 m.

Where this shows up in industry

IRC:SP:23 on vertical curves for highways uses these heights, 1.2 m for the driver's eye and 0.15 m for the object, when it sizes summit curves for stopping sight distance.

GATE 2023 · CE1 · Q.21MCQ · 1 markHighway geometric design

Sag or crest vertical curve: which combinations of approach and departure grades are correct

and are the slopes of the approach and departure grades of a vertical curve, respectively.

Given and
Statement 1: followed by results in a sag vertical curve.
Statement 2: followed by results in a sag vertical curve.
Statement 3: followed by results in a crest vertical curve.

Which option amongst the following is true?

  1. (A)Statement 1 and Statement 3 are correct; Statement 2 is wrong
  2. (B)Statement 1 and Statement 2 are correct; Statement 3 is wrong
  3. (C)Statement 1 is correct; Statement 2 and Statement 3 are wrong
  4. (D)Statement 2 is correct; Statement 1 and Statement 3 are wrong

Answer: (A) Statement 1 and Statement 3 are correct; Statement 2 is wrong Official key: A

  1. Take the algebraic grade change . If the road bends upward (concave, a sag or valley curve); if it bends downward (convex, a crest or summit curve).
  2. Statement 1: up at , then up more steeply at . : sag. Correct.
  3. Statement 2: down at , then down more steeply. With 2 % and 4 %, , negative: the profile bends downward, a crest. Wrong.
  4. Statement 3: up, then down. : crest. Correct.
  5. Answer: (A).

Trap: assuming two falling grades must form a valley. A descent that gets steeper curves away from the driver like a summit; only a descent that flattens out (or turns into a climb) is a sag.

Where this shows up in industry

IRC:SP:23 sizes the two cases differently: a summit curve is made long enough for stopping or overtaking sight distance over the crest, while a valley curve is governed by headlight sight distance at night and by riding comfort.

GATE 2023 · CE1 · Q.35NAT · 1 markHighway geometric design

Minimum length of a transition curve for a 300 m radius curve at 15 m/s with an allowable jerk of 0.75 m/s3

For a horizontal curve, the radius of a circular curve is obtained as 300 m with the design speed as 15 m/s. If the allowable jerk is 0.75 m/s3, what is the minimum length (in m, in integer) of the transition curve?

Answer: 15 m Official key: 15 to 15 OR 26 to 27

  1. Along the transition the centripetal acceleration rises from 0 to at the allowable rate (jerk), in the time .
  2. , reached in .
  3. So , giving 15 m.
  4. The key also accepts 26 to 27: IRC's empirical minimum for plain and rolling terrain is with in km/h. Here and . The jerk route is what the question sets up.

Trap: replacing the given jerk with IRC's own gives , inside neither range; using in km/h in gives about 700 m.

Where this shows up in industry

IRC:38 on horizontal curves fixes the transition length as the largest of three values: the rate of change of centrifugal acceleration with C between 0.5 and 0.8 m/s3, the rate at which superelevation is introduced, and the empirical 2.7 V squared over R.

GATE 2023 · CE2 · Q.23MCQ · 1 markHighway geometric design

Stopping sight distance equals braking distance plus the distance travelled during perception-reaction time

Which of the following is equal to the stopping sight distance?

  1. (A)(braking distance required to come to stop) + (distance travelled during the perception-reaction time)
  2. (B)(braking distance required to come to stop) − (distance travelled during the perception-reaction time)
  3. (C)(braking distance required to come to stop)
  4. (D)(distance travelled during the perception-reaction time)

Answer: (A) (braking distance required to come to stop) + (distance travelled during the perception-reaction time) Official key: A

  1. From the moment a driver sees an obstacle the car keeps moving at full speed until the brakes act (perception-reaction or lag time ), then decelerates to rest.
  2. So : lag distance plus braking distance.
  3. Example at 100 km/h (), = 2.5 s, = 0.35: lag distance , braking distance , .
  4. Answer: (A).

Trap: (C) is only the braking part. At highway speeds the reaction part is a large share of the total (here 38 %), which is why slower speeds shorten stopping distances so much: the lag term falls linearly and the braking term with the square of speed.

Where this shows up in industry

IRC 66 sets stopping sight distance with a 2.5 s perception-brake reaction time and a longitudinal friction coefficient falling from 0.40 at low speed to 0.35 at 100 km/h, which gives about 180 m at 100 km/h.

GATE 2023 · CE2 · Q.30MSQ · 1 markHighway geometric design

What extra widening on a horizontal curve depends on (IRC 86:2018): radius, superelevation, lanes, gradient

As per the Indian Roads Congress guidelines (IRC 86: 2018), extra widening depends on which of the following parameters?

  1. (A)Horizontal curve radius
  2. (B)Superelevation
  3. (C)Number of lanes
  4. (D)Longitudinal gradient

Answer: (A) and (C) Official key: A;C

  1. Extra widening has two parts: mechanical widening for the off-tracking of the rear wheels, for lanes and wheelbase , and psychological widening .
  2. Example: two lanes, = 6 m, = 100 m, = 65 km/h: , , total ; one lane gives .
  3. The IRC guideline tabulates the widening by radius band, separately for single-lane and two-lane roads, falling to nil on large radii.
  4. Superelevation and longitudinal gradient appear in neither term. Answer: (A) and (C).

Trap: ticking superelevation because it is designed on the same curve. Superelevation counters the centrifugal force; it does not change how far the rear wheels track inside the front wheels.

Where this shows up in industry

IRC 73 for rural roads and IRC 86 for urban roads both give the extra widening as a table of radius bands for two-lane and single-lane carriageways, applied on the inner edge or split over both edges of the curve and run in over the transition.

GATE 2024 · CE1 · Q.22MCQ · 1 markHighway geometric design

Stopping distance of a car at 60 km/h on a 2% down gradient with 60% brake efficiency

A car is travelling at a speed of 60 km/hr on a section of a National Highway having a downward gradient of 2%. The driver of the car suddenly observes a stopped vehicle on the car path at a distance 130 m ahead, and applies brake. If the brake efficiency is 60%, coefficient of friction is 0.7, driver's reaction time is 2.5 s, and acceleration due to gravity is 9.81 m/s2, the distance (in meters) required by the driver to bring the car to a safe stop lies in the range

  1. (A)126 to 130
  2. (B)41 to 45
  3. (C)33 to 37
  4. (D)75 to 79

Answer: (D) 75 to 79 Official key: D

  1. Speed: .
  2. Lag (reaction) distance: .
  3. Braking with efficiency on a down gradient : the effective retardation coefficient is .
  4. Braking distance: .
  5. Stopping distance , inside 75 to 79: (D). The car stops well short of the vehicle 130 m ahead.

Trap: the other ranges are pieces of the answer: (B) is the lag distance alone, (C) the braking distance alone and (A) the 130 m gap to the stopped vehicle. Forgetting the brake efficiency gives 62.5 m, which is not offered.

Where this shows up in industry

IRC guidance on sight distance for Indian highways uses a 2.5 s perception and brake reaction time with a longitudinal friction coefficient of about 0.35 to 0.40, so a design stopping sight distance for 60 km/h comes out near 80 m on level ground.

GATE 2024 · CE2 · Q.28MCQ · 1 markHighway geometric design

Is the outer edge raised on horizontal curves of highways, railways and taxiways?

In general, the outer edge is raised above the inner edge in horizontal curves for

  1. (A)Highways, Railways, and Taxiways
  2. (B)Highways and Railways only
  3. (C)Railways and Taxiways only
  4. (D)Highways only

Answer: (B) Highways and Railways only Official key: B

  1. Raising the outer edge counteracts the centrifugal force on a vehicle moving fast round a curve.
  2. Highways: yes, superelevation (IRC limits it to 7 % on plain and rolling terrain, 10 % in hills).
  3. Railways: yes, cant (the outer rail is raised).
  4. Taxiways: aircraft taxi slowly (typically well under 50 km/h), and a banked taxiway would tilt the wings and engines towards the ground. Taxiway curves are instead given large radii, extra width and fillets so the main gear stays on the pavement; the cross slope is only for drainage.
  5. Answer: (B) Highways and Railways only.

Trap: assuming every curved path for vehicles is banked. Low speed and aircraft geometry rule out superelevation on taxiways; widening is the airport answer to curves.

Where this shows up in industry

ICAO Annex 14 limits taxiway transverse slope to about 1.5 percent for the larger code letters, purely for drainage, and specifies curve radii and fillet widening so that the main gear keeps a minimum clearance from the pavement edge.

GATE 2024 · CE2 · Q.63NAT · 2 marksHighway geometric design

Summit curve length for truck stopping sight distance at 80 km/h, +3% and -5% grades

A vertical summit curve on a freight corridor is formed at the intersection of two gradients, +3.0% and −5.0%.

Assume the following:
Only large-sized trucks are allowed on this corridor
Design speed = 80 kmph
Eye height of truck drivers above the road surface = 2.30 m
Height of object above the road surface for which trucks need to stop = 0.35 m
Total reaction time of the truck drivers = 2.0 s
Coefficient of longitudinal friction of the road = 0.36
Stopping sight distance gets compensated on the gradient

The design length of the summit curve (in meters) to accommodate the stopping sight distance is ______ (rounded off to 2 decimal places).

Answer: 117.70 m Official key: 117.00 to 120.00

  1. . The gradient effect is compensated, so use the level-road SSD.
  2. .
  3. Deviation angle .
  4. Assume : with .
  5. , which is longer than the SSD, so the assumption holds.
  6. Answer: 117.70 m.

Trap: using IRC car heights (1.2 m eye, 0.15 m object) gives 238 m; applying the 5 % downgrade to the braking distance (SSD 125.6 m) gives 142 m. Both are outside the key.

Where this shows up in industry

IRC:SP:23 sizes summit curves with a 1.2 m driver eye height and a 0.15 m object for cars; a truck driver's higher eye sees farther over a crest, which is why truck-only freight corridors can use shorter summit curves for the same speed.

GATE 2025 · CE1 · Q.35NAT · 1 markHighway geometric design

Circular curve of radius 200 m with tangent length 92 m: deflection angle between the two roads

Road A and Road B are joined by a circular horizontal curve of radius 200 m as shown in the figure. Road A and Road B are tangential to the curve at the points C and D, respectively. Had the curve not been there, straight roads A and B would have met at the point E. The distance from C to E is 92 m. The value of angle (in degrees) is ______ (rounded off to 1 decimal place).

Note: The value of angle is to be calculated only from the consideration of Euclidean geometry and the data given in the problem.

Horizontal curve between Road A and Road BCDEθRoad ARoad BR = 200 m, CE = 92 m

Answer: 49.4 degrees Official key: 48 to 51

  1. is the deflection angle between Road A extended and Road B. The radii to C and D are perpendicular to the roads, so the angle COD at the centre also equals .
  2. CE is the tangent length. In the right triangle O-C-E the angle at O is , so .
  3. , so .
  4. 49.4 degrees (key 48 to 51). Check: the curve length is .

Trap: writing gives , and reporting the interior angle at E gives . The marked angle is the exterior (deflection) angle, and the tangent length uses half of it.

Where this shows up in industry

Highway setting-out works exactly this way: the surveyor fixes the intersection point and measures the deflection angle, then chains back the tangent length R tan(theta/2) to locate the start of the curve; the design tables in IRC:38 list these curve elements.

GATE 2025 · CE2 · Q.20MCQ · 1 markHighway geometric design

The point where a road alignment changes from a tangent to a curve

The point where the road alignment changes from a tangent to a curve is known as ______.

  1. (A)Point of deflection
  2. (B)Point of intersection
  3. (C)Point of curve
  4. (D)Point of tangency

Answer: (C) Point of curve Official key: C

  1. A simple circular curve has three named points.
  2. Point of intersection (PI): where the two straight tangents, extended, meet. The curve does not pass through it.
  3. Point of curve (PC), also called the beginning of curve: where the alignment leaves the first tangent and starts to curve.
  4. Point of tangency (PT), the end of curve: where the curve rejoins the second tangent.
  5. The deflection angle is measured at the PI; there is no standard point called the point of deflection.
  6. So the answer is (C) Point of curve.

Trap: choosing point of tangency, option (D), because the word tangent appears in the question. The PT is where the curve changes back to a tangent, the reverse direction.

Where this shows up in industry

Road plan and profile drawings label the chainage of every PC, PI and PT; the contractor's surveyor uses them to set out the curve with a total station, and design software such as Civil 3D reports the same points in its alignment tables.

GATE 2025 · CE2 · Q.64NAT · 2 marksHighway geometric design

Two-lane curve, radius 300 m, design speed 80 km/h, wheelbase 7 m: extra widening

On a two-lane highway, a horizontal curve of radius 300 m is provided. The design speed is 80 km/h.

If the longest wheelbase of vehicle expected on this highway is 7 m, then the extra widening required (in m) is ______ (round off to two decimal places).

Answer: 0.65 m Official key: 0.63 to 0.66

  1. Extra widening has a mechanical part (rear wheels track inside the front wheels, off-tracking) and a psychological part (drivers keep a wider gap on curves).
  2. Mechanical, for lanes: .
  3. Psychological: .
  4. Total: 0.65 m (key 0.63 to 0.66).

Trap: using one lane in the mechanical term gives m, and leaving out the psychological term gives m; both fall outside the key. On a two-lane road each lane's vehicle off-tracks, so .

Where this shows up in industry

In practice the widening is read from the IRC table for horizontal curves, which gives 0.6 m for a two-lane road with radius between 101 and 300 m, and is added on the inner side of the curve along with the transition curve.

GATE 2026 · CE1 · Q.47MSQ · 2 marksHighway geometric design

Geometric design of highways: friction for curves vs sight distance, superelevation, grade compensation, summit curves

Which of the following statements is/are TRUE in the context of the geometric design of highways?

  1. (A)The coefficient of friction used for the design of horizontal curves is lower than the coefficient of friction used in the computation of the sight distances.
  2. (B)Centrifugal force at horizontal curve is counteracted by raising the middle of the pavement with respect to the edges.
  3. (C)Grade compensation is achieved by increasing the gradient of the horizontal curve.
  4. (D)Under identical conditions, the design length of the summit curve of a road having unidirectional flow will be greater than that of the same road having bidirectional flow.

Answer: (A) Official key: A

  1. (A) TRUE: IRC practice takes a lateral friction of 0.15 for horizontal curves (kept low for comfort and safety) and a longitudinal friction of 0.35 to 0.40 for stopping sight distance.
  2. (B) FALSE: centrifugal force is countered by superelevation, raising the outer edge above the inner edge. Raising the middle above the edges is camber, for drainage.
  3. (C) FALSE: grade compensation reduces the gradient on a curve, because curve resistance adds to grade resistance.
  4. (D) FALSE: a one-way (divided) road needs only the stopping sight distance; a two-way road also has to cover overtaking or intermediate sight distance, so its summit curve is the longer one.
  5. Answer (A) only.

Trap: ticking (B) because it mentions raising the pavement; that describes camber, not superelevation.

Where this shows up in industry

IRC geometric design standards for rural highways use a lateral friction of 0.15 when sizing superelevation on curves but a much higher longitudinal friction for stopping sight distance, and they cap superelevation at 7 % on plain and rolling terrain.

GATE 2026 · CE2 · Q.23MCQ · 1 markHighway geometric design

SSD needed when an incident diverts traffic onto the other carriageway of a four-lane divided road (360 m normally)

An incident occurred on one side of a median on a four-lane dual carriageway road section. This incident disrupted the traffic movement in one direction. Traffic police diverted the traffic from disrupted side to the other side through an opening in a median. The desired sight distance on the four-lane dual carriageway was kept as 360 m under normal conditions. The Stopping Sight Distance (SSD, in m), which should be available on the operating road section after the incident, is

  1. (A)360
  2. (B)240
  3. (C)180
  4. (D)720

Answer: (C) 180 Official key: C

  1. On a divided carriageway all vehicles move one way, so the sight distance of 360 m only has to let one vehicle stop for an obstruction.
  2. After the diversion one carriageway carries two-way traffic. Two vehicles approaching each other in the same lane (for example, one overtaking) must both stop within the sight distance on the ground.
  3. The sight available is still 360 m, so each vehicle's SSD must be m: speeds on the operating section have to be cut until the SSD is 180 m.
  4. Answer (C) 180 m.

Trap: doubling 360 to 720 m, option (D), applies the two-way rule in the wrong direction; the sight on the ground does not change, so the stopping distance demanded of each vehicle has to halve.

Where this shows up in industry

When a carriageway of a divided highway is closed for an accident or repairs, IRC work-zone guidance calls for a posted lower speed limit, cones and signs through the crossover, precisely because the open carriageway now carries opposing traffic.

GATE 2026 · CE2 · Q.34NAT · 1 markHighway geometric design

Length of a vertical curve: downgrade 1 in 100 meets upgrade 1 in 125, rate of change of grade 0.10 % per 30 m

A downgrade of 1 in 100 meets an upgrade of 1 in 125 on a road. If the rate of change of grade is 0.10 % per 30 m, the length (in m) of the vertical curve between the two grades is ______ (rounded off to the nearest integer).

Answer: 540 m Official key: 540 to 540

  1. The rate of change of grade fixes how quickly the curve may turn, so the length is the total change of grade divided by that rate.
  2. Grades: % and %.
  3. Total change of grade (deviation angle): %.
  4. At 0.10 % per 30 m: m.
  5. Answer 540 m; a downgrade meeting an upgrade forms a valley curve.

Trap: subtracting the magnitudes, %, gives 60 m. When the grades have opposite signs the change of grade is their sum.

Where this shows up in industry

Highway vertical curves are laid out as parabolas because a parabola changes grade at a constant rate; the length is then checked against sight distance and, for valley curves, headlight distance and comfort before the profile is fixed in Civil 3D or similar software.

GATE 2026 · CE2 · Q.61NAT · 2 marksHighway geometric design

Valley curve length from headlight sight distance: 1 in 40 down meets 1 in 50 up, SSD 90 m, beam 1.2 degrees

A vertical curve is formed by a descending gradient of 1 in 40 meeting an ascending gradient of 1 in 50. Consider the following:

Stopping Sight Distance (SSD) = 90 m
Height of headlight of a vehicle above the road surface = 0.75 m
Headlight beam angle with respect to the longitudinal axis of the vehicle = 1.2°

Based on the sight distance criteria, the design length (in m) of the vertical curve is ______ (rounded off to the nearest integer).

Answer: 63 m Official key: 60 to 67

  1. At night the driver on a valley curve sees only as far as the headlight beam reaches the road, so the curve must be long enough for that distance to equal the SSD.
  2. Valley curve, deviation angle .
  3. Headlight term: m.
  4. Try : m, which is less than 90 m, so the assumption fails.
  5. Use : m.
  6. Answer 63 m.

Trap: stopping at the formula gives 69 m, outside the key; always check the assumption against the result.

Where this shows up in industry

IRC practice sizes valley curves on unlit roads by headlight sight distance with a headlight height of 0.75 m and a beam spread of 1 degree; this question uses 1.2 degrees, and comfort (centrifugal acceleration) is checked as a second criterion.

GATE 2022 · CE2 · Q.35NAT · 1 markRailway and airport engineering

Runway base length 1500 m at mean sea level: actual length at an altitude of 300 m

The base length of the runway at the mean sea level (MSL) is 1500 m. If the runway is located at an altitude of 300 m above the MSL, the actual length (in m) of the runway to be provided is ____________. (round off to the nearest integer)

Answer: 1605 m Official key: 1602 to 1606

  1. Thinner air at altitude gives less lift and thrust, so the ICAO elevation correction adds 7 percent of the basic length for every 300 m above mean sea level.
  2. Correction: m.
  3. Corrected length: 1605 m.
  4. Only elevation is asked here; temperature (1 percent per degree above the standard temperature) and gradient corrections would follow in that order, and elevation plus temperature together should not exceed 35 percent.

Trap: applying 7 percent per 1000 m gives 1531.5 m, outside the key. The ICAO rate is per 300 m.

Where this shows up in industry

These corrections are why high-altitude Indian airports such as Leh, at about 3,256 m above mean sea level, need far longer runways than coastal airports for the same aircraft.

GATE 2024 · CE1 · Q.23MCQ · 1 markRailway and airport engineering

ICAO elevation correction: basic runway length rises by x % for every y m above mean sea level

As per the International Civil Aviation Organization (ICAO), the basic runway length is increased by x (%) for every y (m) raise in elevation from the Mean Sea Level (MSL). The values of x and y, respectively, are

  1. (A)7% and 300 m
  2. (B)5% and 200 m
  3. (C)4% and 500 m
  4. (D)10% and 1000 m

Answer: (A) 7% and 300 m Official key: A

  1. Air is thinner at altitude, so an aircraft needs a higher ground speed and a longer roll to lift off.
  2. ICAO's elevation correction: increase the basic runway length (sea level, standard atmosphere, level runway) by 7 % for every 300 m of elevation above MSL.
  3. The corrected length is then raised again for temperature (1 % for every 1 degree C by which the aerodrome reference temperature exceeds the standard temperature at that elevation) and for the effective gradient.
  4. Answer: (A) 7 % and 300 m.

Trap: mixing up the three corrections. 1 % per degree is the temperature correction; the gradient correction is a percentage per 1 % of effective gradient. None of them is 5 % per 200 m or 10 % per 1000 m. Also remember ICAO checks that elevation and temperature corrections together do not exceed 35 %; beyond that a site-specific study is needed.

Where this shows up in industry

High-altitude Indian airports such as Leh, at about 3,256 m above sea level, need far longer runways than a sea-level airport for the same aircraft, which is why their operations are also restricted to cooler morning hours.

GATE 2024 · CE1 · Q.62NAT · 2 marksRailway and airport engineering

Equilibrium cant on a 437 m radius Broad Gauge curve from the weighted average speed of 58 trains

The number of trains and their corresponding speeds for a curved Broad Gauge section with 437 m radius, are

  • 20 trains travel at a speed of 40 km/hr
  • 15 trains travel at a speed of 50 km/hr
  • 12 trains travel at a speed of 60 km/hr
  • 8 trains travel at a speed of 70 km/hr
  • 3 trains travel at a speed of 80 km/hr

If the gauge (center-to-center distance between the rail heads) is taken as 1750 mm, the required equilibrium cant (in mm) will be ______ (rounded off to the nearest integer).

Answer: 88 mm Official key: 86 to 90

  1. The equilibrium speed for mixed traffic is the weighted average speed of all the trains: .
  2. Equilibrium cant balances the centrifugal force at that speed: , which in practical units is with in mm, in km/h and in m.
  3. (the SI form gives 88.25 mm).
  4. Answer: 88 mm, inside the key 86 to 90.

Trap: designing for the fastest train gives 202 mm, which would make the slow majority run with a large cant excess and wear the inner rail; the plain average of the five speeds (60 km/h) ignores how many trains run at each speed and gives 114 mm.

Where this shows up in industry

Indian Railways caps cant on Broad Gauge at 165 mm and sets equilibrium speed from the speeds of the actual traffic on the section, so mixed goods and passenger lines get a compromise cant with permitted cant deficiency and excess.

GATE 2024 · CE2 · Q.27MCQ · 1 markRailway and airport engineering

Effective gradient of a 2,000 m runway from five longitudinal sections and their gradients

The longitudinal sections of a runway have gradients as shown in the table.

End to end for sections of runway (m)Gradient (%)
0 to 200+1.0
200 to 600−1.0
600 to 1200+0.8
1200 to 1600+0.2
1600 to 2000−0.5

Consider the reduced level (RL) at the starting point of the runway as 100 m. The effective gradient of the runway is

  1. (A)0.02%
  2. (B)0.35%
  3. (C)0.28%
  4. (D)0.18%

Answer: (C) 0.28% Official key: C

  1. Effective gradient = (highest RL minus lowest RL on the runway centre line) divided by the runway length.
  2. RL at 0, 200, 600, 1200, 1600 and 2000 m: 100.0, 102.0, 98.0, 102.8, 103.6 and 101.6 m (add length times gradient section by section, e.g. ).
  3. Highest 103.6 m (at 1600 m), lowest 98.0 m (at 600 m), difference 5.6 m.
  4. Effective gradient : (C).

Trap: taking the end-to-end slope, (not offered), or dividing the 5.6 m by the 1,600 m between the start and the high point, which gives the 0.35 % of option (B). The definition always uses the full runway length.

Where this shows up in industry

Runway design applies a correction for effective gradient after the elevation and temperature corrections, so even a small rise between the lowest and highest points of a runway profile adds length that the aerodrome master plan must reserve.

GATE 2024 · CE2 · Q.62NAT · 2 marksRailway and airport engineering

Maximum speed on a 1080 m Broad Gauge curve built for 70 km/h with 10 cm cant deficiency

A horizontal curve of radius 1080 m (with transition curves on either side) in a Broad Gauge railway track is designed and constructed for an equilibrium speed of 70 kmph. However, a few years after construction, the Railway Authorities decided to run express trains on this track. The maximum allowable cant deficiency is 10 cm.

The maximum restricted speed (in kmph) of the express trains running on this track is ______ (rounded off to the nearest integer).

Answer: 113 km/h Official key: 112 to 116

  1. Cant actually provided, for 70 km/h with BG gauge 1750 mm (centre to centre of rail heads): .
  2. A faster train may run with a cant deficiency , i.e. as if the cant were .
  3. , so .
  4. Indian Railways' formula for transitioned curves, , gives 113.1 km/h; the general limit km/h does not govern.
  5. Answer: 113 km/h.

Trap: using the cant deficiency alone, as if no cant had been built, gives 89 km/h.

Where this shows up in industry

The Indian Railways Permanent Way Manual normally allows 75 mm cant deficiency on Broad Gauge and up to 100 mm on nominated high-speed routes, and raising sectional speeds on existing lines is checked curve by curve with exactly this calculation.

GATE 2025 · CE1 · Q.25MCQ · 1 markRailway and airport engineering

Maximum degree of curve allowed for railways in a mountainous region

The maximum degree of the curve that can be used for railways in a mountainous region is

  1. (A)10
  2. (B)20
  3. (C)50
  4. (D)40

Answer: (D) 40 Official key: D

  1. On Indian Railways the degree of a curve is the angle subtended at the centre by a 30.5 m (100 ft) chord, so metres.
  2. The limits are 10 degrees on broad gauge (), 16 degrees on metre gauge () and 40 degrees on narrow gauge ().
  3. Mountain lines are built to narrow gauge precisely because it allows such sharp curves along hill slopes, so the maximum is 40 degrees, option (D).

Trap: answering 10 degrees, option (A), which is the broad-gauge limit. The question asks for the sharpest curve used anywhere, which belongs to narrow-gauge hill railways.

Where this shows up in industry

The narrow-gauge hill railways to Darjeeling, Shimla and Matheran wind along slopes on curves far sharper than any broad-gauge line could take, which is why they still run at low speeds with small locomotives.

GATE 2025 · CE2 · Q.19MCQ · 1 markRailway and airport engineering

Runway 700 m after elevation and temperature corrections: length after the 1 % effective gradient correction

After applying the correction for elevation and temperature, the runway length is 700 m. The corrected runway length (in m) for an effective gradient of 1% is ______ (round off to the nearest integer).

  1. (A)840
  2. (B)700
  3. (C)720
  4. (D)740

Answer: (A) 840 Official key: A

  1. The basic runway length is corrected in a fixed order: elevation (+7 % per 300 m above mean sea level), then temperature (+1 % per the reference temperature exceeds the standard), then gradient.
  2. The gradient correction adds 20 % for every 1 % of effective gradient (the difference between the highest and lowest runway elevations divided by the runway length), applied to the length already corrected for elevation and temperature.
  3. 840 m, option (A).

Trap: applying the 35 % cap, which limits only the combined elevation and temperature corrections, to the gradient step, or adding a flat 1 % or 20 m. A 10 % per 1 % rule would give 770 m, which is not an option.

Where this shows up in industry

Runway lengths at Indian airports are checked against the take-off and landing performance charts of the critical aircraft; the textbook elevation, temperature and gradient corrections show why high-altitude airports such as Leh need much longer runways for the same aircraft.

GATE 2026 · CE1 · Q.19MCQ · 1 markRailway and airport engineering

Corrections to the basic runway length for elevation, temperature and effective gradient

Corrections are applied to the basic length of the runway strip considering:
(i) The elevation H (in m) of the airport above Mean Sea Level (MSL)
(ii) Corrected air temperature T (in °C) with respect to the standard temperature at elevation H
(iii) The effective gradient G (in %) along the length of the runway

Respective correction applied to the basic length of the runway is:

  1. (A) ; ;
  2. (B) ; ;
  3. (C) ; ;
  4. (D) ; ;

Answer: Marks to all: no option is fully correct (standard factors 0.07 H/300, 0.01 T and 0.20 G) Official key: MTA

  1. The ICAO corrections to the basic runway length, applied one after another, are: elevation +7 % per 300 m, ; temperature +1 % per °C by which the airport reference temperature exceeds the standard temperature at that elevation, ; effective gradient +20 % per 1 %, .
  2. Option (A) has the first two right but uses 0.10 for the gradient; (B), (C) and (D) swap the factors. No option is fully correct, so GATE awarded marks to all.
  3. Example: a basic length of 1800 m at 600 m elevation grows by 14 % to 2052 m; 10 °C of temperature excess takes it to 2257 m, and a 0.5 % effective gradient to 2483 m.

Trap: the ICAO rule that the elevation and temperature corrections together should not exceed 35 % is a check on their sum, not a factor; the gradient factor is 20 %, which is why (A) is not correct.

Where this shows up in industry

High-altitude airports such as Leh in Ladakh need much longer runways for the same aircraft because thin air cuts lift and engine thrust; these ICAO factor corrections give the planning length before the aircraft makers' performance charts are checked.

GATE 2026 · CE1 · Q.24MSQ · 1 markRailway and airport engineering

Cant on a Broad Gauge track for equilibrium speed V, dynamic gauge G and radius R: which formulae are right?

Cant on a Broad Gauge railway track is calculated for an equilibrium speed (in km/h), dynamic gauge (in mm) and radius of curve (in m) using formula/formulae:

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) and (B) Official key: A;B

  1. At equilibrium speed the weight and the centrifugal force give a resultant normal to the canted track: .
  2. With in km/h () and , in mm: , since . So (A) is the general formula.
  3. For Broad Gauge the dynamic gauge (centre-to-centre of the rail heads) is 1750 mm: , so , option (B).
  4. Answer (A) and (B).

Trap: (C) uses the track gauge 1676 mm () instead of the dynamic gauge, and (D) is the Metre Gauge version ().

Where this shows up in industry

Indian Railways cants every curve with this relation and then limits both the cant and the cant deficiency, so the equilibrium speed chosen for a curve shared by expresses and freight trains is a compromise between them.

GATE 2026 · CE2 · Q.24MCQ · 1 markRailway and airport engineering

Cant deficiency and cant excess: which relates to faster trains and which to slower ones?

Which one of the following statements is TRUE?

  1. (A)Cant deficiency is related to train moving faster, and Cant excess is related to train moving slower.
  2. (B)Cant deficiency is related to train moving slower, and Cant excess is related to train moving faster.
  3. (C)Cant deficiency is related to train moving on the main line, and Cant excess is related to train moving on the branch line.
  4. (D)Cant deficiency is related to train moving on the branch line, and Cant excess is related to train moving on the main line.

Answer: (A) Cant deficiency is related to train moving faster, and Cant excess is related to train moving slower. Official key: A

  1. Cant is provided for an equilibrium speed ; the cant a train needs grows with .
  2. A train running faster than needs more cant than is provided: the shortfall is the cant deficiency. Example on BG, m, km/h: provided cant mm; at 100 km/h the need is 50 mm more.
  3. A train running slower has more cant than it needs: cant excess, 39 mm at 60 km/h.
  4. Answer (A).

Trap: (C) and (D) mix up a related idea, the negative cant on a branch line taking off a canted main line; deficiency and excess are about speed, not about which line.

Where this shows up in industry

Indian Railways sets limits on both quantities: cant deficiency governs how fast an express may take a curve, and cant excess governs how much slow, heavy freight trains overload and wear the inner rail.

GATE 2026 · CE2 · Q.25MCQ · 1 markRailway and airport engineering

What is the primary purpose of a windrose diagram in airport design?

The primary purpose of the Windrose diagram is for the design of

  1. (A)length of a runway.
  2. (B)orientation of a runway.
  3. (C)width of a runway.
  4. (D)gradient of a runway.

Answer: (B) orientation of a runway. Official key: B

  1. A windrose plots, for each compass direction, how often the wind blows from it and at what speed, from several years of records.
  2. Aircraft take off and land into the wind, and the crosswind component on a runway must stay within limits. Overlaying a runway strip on the windrose shows the percentage of time the crosswind is acceptable, the wind coverage.
  3. The direction with the highest coverage fixes the orientation of the runway.
  4. Answer (B).

Trap: (A) length. Wind does matter for take-off distance, but runway length is set by the aircraft, elevation, temperature and gradient corrections, not by the windrose.

Where this shows up in industry

ICAO Annex 14 asks that a runway system be usable at least 95 % of the time within the permissible crosswind, so airport planners draw a windrose from years of weather records before fixing the runway direction.

GATE 2022 · CE2 · Q.64NAT · 2 marksHighway materials and bituminous mixes

Air voids in a mix of 260 g coarse (G 2.6) and 240 g fine (G 2.4) aggregate with bulk specific gravity 2.3

It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine aggregates. The specific gravities of the coarse and fine aggregates are 2.6 and 2.4, respectively. The bulk specific gravity of the mix is 2.3.

The percentage air voids in the mix is ____________. (round off to the nearest integer)

Answer: 8 % Official key: 8 to 8

  1. Theoretical (void-free) specific gravity by mass-weighted volumes: .
  2. .
  3. Air voids: 8 %.
  4. Here the coarse and fine fractions happen to occupy equal volumes (100 units each), so is also their simple average; with unequal volumes it would not be, and the weighted form is the safe one.

Trap: dividing by the bulk specific gravity instead of gives 8.7 %, which rounds to 9 and misses the key. Air voids are a fraction of the total volume, which is what normalises.

Where this shows up in industry

MoRTH specifications ask for 3 to 5 percent air voids in Marshall-designed dense bituminous macadam and bituminous concrete; too many voids let in water and air, too few cause bleeding and rutting.

GATE 2023 · CE1 · Q.51MSQ · 2 marksHighway materials and bituminous mixes

Match how bitumen and aggregate tests are reported: ratio, percentage, temperature, length

Which of the following options match the test reporting conventions with the given material tests in the table?

Test reporting conventionMaterial test
(P) Reported as ratio(I) Solubility of bitumen
(Q) Reported as percentage(II) Softening point of bitumen
(R) Reported in temperature(III) Los Angeles abrasion test
(S) Reported in length(IV) Flash point of bitumen
(V) Ductility of bitumen
(VI) Specific gravity of bitumen
(VII) Thin film oven test
  1. (A)(P) - (VI); (Q) - (I); (R) - (II); (S) - (VII)
  2. (B)(P) - (VI); (Q) - (III); (R) - (IV); (S) - (V)
  3. (C)(P) - (VI); (Q) - (I); (R) - (II); (S) - (V)
  4. (D)(P) - (VI); (Q) - (III); (R) - (IV); (S) - (VII)

Answer: (B) and (C) Official key: B;C

  1. Ratio: specific gravity is the mass of bitumen over the mass of an equal volume of water, a pure number. P - VI in every option.
  2. Percentage: solubility in trichloroethylene is the per cent of the sample that dissolves (I), and the Los Angeles abrasion value is the per cent of aggregate worn finer than the 1.70 mm sieve (III). Both are percentages.
  3. Temperature: the softening point (ring and ball, II) and the flash point (IV) are both reported in degrees Celsius.
  4. Length: ductility (V) is the distance in cm a briquette stretches before it breaks.
  5. The thin film oven test (VII) is an ageing step: it is reported as per cent loss in mass and as the penetration or viscosity retained, never as a length. So (A) and (D) fail on S - VII; (B) and (C) are both fully correct: (B) and (C).

Trap: picking only one of (B) and (C). Since I and III are both percentages and II and IV both temperatures, the two options are equally right, which is why this MSQ has two answers.

Where this shows up in industry

IS 73:2013, the Indian specification for paving bitumen grades VG-10 to VG-40, lists exactly these properties with their units: softening point and flash point in degrees Celsius, ductility in cm, solubility in per cent, plus viscosity and tests on the thin film oven residue.

GATE 2024 · CE1 · Q.24MCQ · 1 markHighway materials and bituminous mixes

Which statement on bitumen is false: kinematic viscosity, softening point, flash point or ductility?

Which one of the following statements related to bitumen is FALSE?

  1. (A)Kinematic viscosity is a measure of resistance to the flow of molten bitumen under gravity.
  2. (B)Softer grade bitumen possesses higher softening point than hard grade bitumen.
  3. (C)Flash point of bitumen is the lowest temperature at which application of a test flame causes vapours of the bitumen to catch an instant fire in the form of flash under specified test conditions.
  4. (D)Ductility test is carried out on bitumen to test its adhesive property and ability to stretch.

Answer: (B) Softer grade bitumen possesses higher softening point than hard grade bitumen. Official key: B

  1. (A) True. Kinematic viscosity (IS 1206 Part 3, usually at 135 degree C) is measured by timing molten bitumen flowing through a capillary under its own weight, so it measures resistance to flow under gravity.
  2. (B) False. The ring-and-ball softening point is the temperature at which bitumen softens enough to let a steel ball sink through it. A softer grade softens at a lower temperature, so it has a lower softening point.
  3. (C) True. That is the definition of the flash point; it fixes a safe heating temperature at the plant.
  4. (D) True. The ductility test stretches a briquette until it breaks; good ductility means the binder can stretch and stay bonded to the aggregate.
  5. The FALSE statement is (B).

Trap: penetration and softening point move in opposite directions. Softer bitumen has a higher penetration but a lower softening point; hard grades are the ones that stay solid in hot climates.

Where this shows up in industry

Under IS 73, India's viscosity-graded paving bitumens show this order: the minimum softening point rises from 40 degree C for VG-10 to 47 for VG-30 and 50 for VG-40, which is why the harder VG-40 is chosen for hot, heavily loaded highways.

GATE 2024 · CE2 · Q.46MSQ · 2 marksHighway materials and bituminous mixes

Correct statements on CBR origin correction, aggregate tests, VG bitumen grading and VMA

In the context of pavement material characterization, the CORRECT statement(s) is/are

  1. (A)The load penetration curve of CBR test may need origin correction due to the non-vertical penetrating plunger of the loading machine.
  2. (B)The toughness and hardness of road aggregates are determined by Los Angeles abrasion test and aggregate impact test, respectively.
  3. (C)Grading of normal (unmodified) bitumen binders is done based on viscosity test results.
  4. (D)In compacted bituminous mix, Voids in the Mineral Aggregate (VMA) is equal to the sum of total volume of air voids () and total volume of bitumen ().

Answer: (A) and (C) and (D); (A) and (C) also accepted Official key: A;C;D OR A;C

  1. (A) Correct. The start of a CBR load-penetration curve is often concave upward because the plunger does not seat squarely on an uneven surface; the straight part is extended to the axis and the origin shifted before reading the loads at 2.5 and 5.0 mm.
  2. (B) Incorrect: the tests are swapped. The aggregate impact test measures toughness (resistance to impact); the Los Angeles abrasion test measures hardness (resistance to wear).
  3. (C) Correct. Since IS 73:2006, Indian paving bitumens are graded VG-10 to VG-40 by absolute viscosity at 60 degree C, replacing penetration grading.
  4. (D) The textbook relation is , so it reads correct. Strictly, VMA includes only the effective bitumen; bitumen absorbed into aggregate pores sits inside the aggregate's volume. That is why the key accepts both answers.
  5. Answer: (A), (C) and (D); (A) and (C) alone also earned marks.

Trap: ticking (B) because both tests are familiar; the pairing is reversed.

Where this shows up in industry

MoRTH specifications for bituminous concrete limit the Los Angeles abrasion value to 30 percent and the aggregate impact value to 24 percent, and mix designs report VMA computed from effective bitumen, so absorption is measured, not assumed.

GATE 2025 · CE1 · Q.24MCQ · 1 markHighway materials and bituminous mixes

Bitumen tests: penetration, ring and ball softening point and ductility, which statement is false

In the context of testing bitumen, which one of the following statements is FALSE:

  1. (A)The depth of penetration of needle in the standard penetration test is measured in the units of one-tenth of millimeter
  2. (B)Softening point is measured using a ring and ball apparatus
  3. (C)Softening point is measured in the units of time
  4. (D)Ductility is measured in the units of length

Answer: (C) Softening point is measured in the units of time Official key: C

  1. (A) True: a standard needle under 100 g sinks into the sample at for 5 s, and the depth is reported in units of 0.1 mm, so a penetration of 60 means 6 mm.
  2. (B) True: the ring and ball apparatus holds a steel ball on a bitumen disc in a brass ring, heated in a water or glycerine bath at per minute.
  3. (C) False: the softening point is the temperature at which the softened bitumen sags 25 mm under the ball and touches the base plate, reported in . Time does not appear in the result.
  4. (D) True: ductility is the distance a briquette stretches at 50 mm/min before the thread breaks, reported in cm.
  5. Answer: (C).

Trap: because the bath is heated at a fixed rate, one may think the test reports a time. The heating rate only standardises the test; the result is a temperature.

Where this shows up in industry

Indian paving bitumen is graded by viscosity under IS 73:2013 (VG-10 to VG-40), but penetration (IS 1203), softening point (IS 1205) and ductility (IS 1208) are still part of every supplier's test certificate and every site laboratory's acceptance checks.

GATE 2025 · CE1 · Q.65NAT · 2 marksHighway materials and bituminous mixes

Compacted bituminous specimen 1260 g in 525 cm3, theoretical maximum specific gravity 2.510: air voids

During determination of the bulk specific gravity of compacted bituminous specimen, the mass in air of the specimen is 1260 g and volume is 525 cm3. The density of water is 1.0 g/cm3. The theoretical maximum specific gravity of mix is 2.510.

The percentage air voids in the compacted specimen is ______ (rounded off to 2 decimal places).

Answer: 4.38 % Official key: 4.22 to 4.56

  1. Bulk specific gravity of the compacted specimen: .
  2. The theoretical maximum specific gravity is the mix with no air at all.
  3. Air voids: .
  4. 4.38 % (key 4.22 to 4.56), inside the usual 3 to 5 % design band for dense mixes.

Trap: dividing the difference by instead of gives %, just outside the key. Air voids are a fraction of the total specimen volume, so the reference is the voidless mix, .

Where this shows up in industry

MoRTH Section 500 specifications require dense bituminous macadam and bituminous concrete to be designed at 3 to 5 % air voids, so site laboratories compute Gmb and Gmm for Marshall specimens and field cores daily to check compaction.

GATE 2025 · CE2 · Q.28MSQ · 1 markHighway materials and bituminous mixes

Bitumen softening point in warm climates, viscosity, 3-5 % air voids and solubility: which is incorrect

Which of the following statements is/are INCORRECT?

  1. (A)Bitumen having lower softening point is preferred in warm climate regions.
  2. (B)The viscosity of bitumen influences the mixing and compaction of bituminous mix.
  3. (C)The air voids in the range of 3% to 5% are required to arrive at the optimum bitumen content.
  4. (D)The purity of bitumen can be determined using Solubility Test.

Answer: (A) Official key: A

  1. (A) Incorrect: a bitumen that softens at a low temperature would bleed and rut under hot sun and heavy wheels. Warm regions need a harder binder with a higher softening point; soft, low softening point grades suit cold regions, where cracking is the risk.
  2. (B) Correct: mixing and compaction temperatures are chosen so that the binder viscosity is low enough to coat the aggregate and to let rollers compact the mix.
  3. (C) Correct: in the Marshall method the optimum bitumen content is fixed at a target air void content, typically 4 %, within the 3 to 5 % band.
  4. (D) Correct: the solubility test dissolves bitumen in trichloroethylene; the insoluble residue is the impurity, and paving bitumen must be at least 99 % soluble.
  5. Only (A) is incorrect: answer (A).

Trap: taking (C) as wrong because the optimum is often quoted at exactly 4 %. The 4 % target sits inside the 3 to 5 % band, so the statement holds.

Where this shows up in industry

IS 73:2013 viscosity grades are chosen by climate and traffic: softer VG-10 for cold regions, VG-30 for most Indian highways and the harder VG-40 for hot, heavily loaded stretches such as junctions and climbing lanes.

GATE 2026 · CE1 · Q.61NAT · 2 marksHighway materials and bituminous mixes

Voids Filled with Bitumen of a mix with 58/25/12/5 % coarse, fine, filler and binder and bulk specific gravity 2.2

In a bituminous mix, the percentage by weight of coarse aggregate, fine aggregate, filler, and bituminous binder is 58, 25, 12, and 5, respectively. The corresponding specific gravity of these materials is 2.68, 2.45, 2.42, and 1.15. The bulk specific gravity of the mix is 2.2.

The Voids Filled with Bitumen (VFB, in percentage) is ______ (rounded off to the nearest integer).

Answer: 50 % Official key: 48 to 52

  1. VFB is the share of the voids in the mineral aggregate (VMA) that the binder fills; find the air voids and the binder volume first.
  2. Theoretical maximum specific gravity: , where , so .
  3. Air voids: %.
  4. Volume of bitumen: %.
  5. %, so %.
  6. Answer 50 %.

Trap: using the binder's 5 % by weight as if it were a volume, %, is outside the key; the bitumen volume must be scaled by .

Where this shows up in industry

Marshall mix designs for dense bituminous macadam and bituminous concrete under the MoRTH specifications must land VFB in the 65 to 75 % band; a mix at about 50 % like this one has too little binder for its voids and would be redesigned.

From GATE prep to a highway and transportation engineering career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.