GATE Civil: Engineering Mechanics and Solid Mechanics (SFD and BMD, stresses, torsion, Mohr's circle, buckling), previous-year questions solved, part 2

Part 2 of 3 of the Solid Mechanics hub: 12 more official GATE CE questions on shear force and bending moment in determinate beams and stress, strain, axial and thermal members, each solved step by step and checked against the official answer key. Part 1 covers engineering mechanics: forces, friction, centroids and vibration, bending, shear stress, shear centre and torsion and stress transformation, thin shells, combined stress and buckling.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 12 of 36 questions on this page

GATE 2023 · CE1 · Q.49MSQ · 2 marksShear force and bending moment in determinate beams

Simply supported beam with equal and opposite couples M at the third points: reactions, shear, moment, deflection

Consider the beam shown in the figure (not to scale), on a hinge support at end A and a roller support at end B. The beam has a constant flexural rigidity, and is subjected to the external moments of magnitude at one-third spans, as shown in the figure. Which of the following statements is/are TRUE?

Beam AB on a hinge at A and a roller at B, three equal parts L; an anticlockwise couple M at the first third point and a clockwise couple M at the second third pointMMABLLL
  1. (A)Support reactions are zero
  2. (B)Shear force is zero everywhere
  3. (C)Bending moment is zero everywhere
  4. (D)Deflection is zero everywhere

Answer: (A, B) Official key: A, B

  1. The two couples are equal and opposite, so their resultant is zero. Moments about A: , so ; vertical equilibrium gives . (A) is true.
  2. With no transverse force anywhere, the shear force is zero on every section. (B) is true.
  3. Bending moment is not zero: a section in the middle third has the anticlockwise couple on its left, so (hogging) between the couples, and zero in the outer thirds. (C) is false.
  4. The middle third bends with curvature , so the beam deflects: integrating gives a mid-span rise of (the outer thirds stay straight but tilt). (D) is false.
  5. Answer: (A, B).

Trap: zero reactions and zero shear do not mean zero moment. A couple changes the bending moment by a jump without needing any shear, which is why (C) and (D) fail.

Where this shows up in industry

Self-equilibrated couples like these appear when a prestressing cable is anchored eccentrically at two points along a beam: the supports feel nothing, yet the segment between the anchorages bends and cambers, which designers must account for.

GATE 2024 · CE1 · Q.39MCQ · 2 marksShear force and bending moment in determinate beams

Support reactions of a three-support beam with an internal hinge and a UDL between supports A and B

The beam shown in the figure is subjected to a uniformly distributed downward load of intensity between supports A and B.

Considering the upward reactions as positive, the support reactions are

Beam with an internal hinge, pin at A, rollers at B and C, UDL q from A to BqhingeABClll
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. The internal hinge carries no bending moment. Together with and for the whole beam, this gives three equations for , and : the beam is statically determinate.
  2. Part left of the hinge (length , load at ): , so .
  3. The hinge then passes a shear of downward onto the right part.
  4. Right part, anticlockwise moments about B: , so . C pulls the beam down.
  5. : .
  6. Answer: (A) , , .

Trap: all four options add up to the total load , so vertical equilibrium cannot pick the answer. Moments about A, , rule out (B), (C) and (D), and the hinge condition confirms (A).

Where this shows up in industry

Gerber (cantilever-suspended) bridge girders use internal hinges in exactly this way; the uplift at the end support means its bearing must be anchored against lifting, a detail that has to be designed, not assumed.

GATE 2025 · CE1 · Q.41MSQ · 2 marksShear force and bending moment in determinate beams

Beam with an internal hinge and a couple applied through a post at D: which SFD and BMD statements are correct?

Consider the beam ACDEB given in the figure. Which of the following statements is/are correct:

Beam ACDEB fixed at A, internal hinge at C 5 m from A carrying a 3 kN downward load, a rigid vertical post at D 2 m further on with a 4 kN force to the right 1 m above the beam and a 4 kN force to the left 1 m below it, a roller support at E 2 m beyond D, and a 2 kN downward load at the free end B 2 m beyond E3 kN2 kN4 kN4 kN1 m1 mACDEBinternal hinge5 m2 m2 m2 m
  1. (A)Bending moment is zero between the points A and C
  2. (B)There is a sudden jump in shear force at the point D
  3. (C)There is a sudden jump in bending moment at the point E
  4. (D)Bending moment is zero somewhere between the points D and E

Answer: (A) and (D) Official key: A;D

  1. The two 4 kN forces at D are equal, opposite and 2 m apart: a clockwise couple of kN.m, with no net force.
  2. Part CDEB, moments about the hinge C: , so kN. Vertical balance puts 3 kN downward on CB at C, so CB pushes 3 kN up on AC, which cancels the 3 kN load at C. AC carries no load at all: zero moment. (A) is true.
  3. A couple makes the BMD jump (from to kN.m at D) but leaves the shear unchanged. (B) is false.
  4. At the roller E only the shear jumps; the moment, kN.m, is continuous. (C) is false.
  5. Between D and E, : at D and at E, zero at m. (D) is true.
  6. Answer: (A) and (D).

Trap: a couple causes a jump in the bending moment, not the shear; a concentrated force causes a jump in shear, not moment. (B) and (C) swap the two.

Where this shows up in industry

Gerber beams with internal hinges are used in long-span bridges and roof purlins so that settlement causes no extra moments; brackets and eccentric connections load beams with couples exactly like the post at D.

GATE 2026 · CE2 · Q.18MCQ · 1 markShear force and bending moment in determinate beams

Beam fixed at F and L with internal hinges at G and J: upward vertical reaction at L

The horizontal beam shown in the figure has fixed supports at F and L. Internal hinges are provided at locations G and J. The beam supports vertically downward concentrated loads as well as uniformly distributed loads, as shown in the figure.

(Figure not to scale)

The upward vertical reaction (in kN) at the support L is

Beam fixed at F and L, internal hinges at G and J; 5 kN/m on FG (4 m), 20 kN at G, 30 kN at H midway between G and J (2 m each side), 4 kN/m on KL; spans FG 4 m, GH, HJ, JK and KL 2 m each5 kN/m20 kN30 kN4 kN/mFGHJKLhingehinge4 m2 m2 m2 m2 mRedrawn, not to scale
  1. (A)23
  2. (B)33
  3. (C)43
  4. (D)58

Answer: (A) 23 Official key: A

  1. The hinges split the beam into three parts: cantilever FG, a drop-in span GJ resting on the two hinges, and cantilever JL. A hinge passes shear but no moment.
  2. Span GJ (4 m) carries 30 kN at H, its midpoint, so each hinge takes kN.
  3. Cantilever JL (4 m) carries the hinge force kN down at J and kN on KL.
  4. kN. (Its fixing moment is kN m.)
  5. Check: kN and kN, the total load.
  6. Answer (A) 23 kN.

Trap: the 20 kN load sits at hinge G, so it goes straight into cantilever FG; sending half of it to L gives 33 (B), all of it 43 (C), and adding every load near L gives 58 (D).

Where this shows up in industry

Gerber or cantilever-and-suspended-span bridges use internal hinges just like this: the suspended span drops in between two cantilevers, so its reactions come from statics alone and settlement or temperature at one support does not lock stresses into the rest of the deck.

GATE 2022 · CE2 · Q.13MCQ · 1 markStress, strain, axial and thermal members

Relationship among Young's modulus E, Poisson's ratio and shear modulus G for a linear elastic isotropic material

For a linear elastic and isotropic material, the correct relationship among Young’s modulus of elasticity (), Poisson’s ratio (), and shear modulus () is

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Take pure shear . Its principal stresses are and , on planes at 45°.
  2. Normal strain along from Hooke's law in two directions: .
  3. For pure shear the engineering shear strain is twice the principal normal strain: .
  4. , so , option (A). Check with steel: GPa, gives GPa.

Trap: (C) and (D) make smaller than , which never happens since for engineering materials. (B) mixes in the bulk-modulus form , which has , not .

Where this shows up in industry

FE programs ask for E and Poisson's ratio and derive G from this relation for isotropic steel and concrete; for timber, composites or rolled plate the relation does not hold and G must be entered separately as an orthotropic property.

GATE 2022 · CE2 · Q.50NAT · 2 marksStress, strain, axial and thermal members

Co-linear rods between fixed supports, one heated by 50 degrees C: joint force that leaves the other rod stress-free

Consider two linearly elastic rods and , each of length , as shown in the figure. The rods are co-linear, and confined between two fixed supports at and . Both the rods are initially stress free. The coefficient of linear thermal expansion is for both the rods. The temperature of the rod is raised by , whereas the temperature of rod remains unchanged. An external horizontal force is now applied at node . It is given that , , m, N. The axial rigidities of the rods and are and , respectively.

To make the axial force in rod equal to zero, the value of the external force (in N) is ______. (round off to the nearest integer)

Two co-linear rods between fixed supports H and J: rod HI of length b and axial rigidity 2AE, rod IJ of length b and axial rigidity AE; horizontal force P applied at node I towards JPbb2AEAEHIJ

Answer: 50 N Official key: 47 to 53

  1. If carries no force and is not heated, its length does not change, so node does not move: .
  2. Then is held at its original length while it wants to expand by m. The force needed to push it back is N, compression.
  3. A compressed rod pushes on its ends, so at rod pushes towards with 50 N. With no force from , equilibrium of node needs towards : N.
  4. Check by the displacement method: with gives exactly at N.

Trap: the thermal force with (both rods resisting in series) is N, which is not the answer. Using for the heated rod gives N.

Where this shows up in industry

Rails, pipelines and bridge bearings restrained at both ends see exactly this locked-in thermal force; expansion joints, loops and sliding bearings exist to let the member move so that the force never builds up.

GATE 2023 · CE1 · Q.12MCQ · 1 markStress, strain, axial and thermal members

Stepped hanger of two square bars with 100 kN shoulder loads: maximum tensile stress anywhere in it

A hanger is made of two bars of different sizes. Each bar has a square cross-section. The hanger is loaded by three-point loads in the mid vertical plane as shown in the figure. Ignore the self-weight of the hanger. What is the maximum tensile stress in N/mm2 anywhere in the hanger without considering stress concentration effects?

Hanger hung from a ceiling: an upper square bar 100 mm wide and a lower square bar 50 mm wide; two 100 kN loads hang from the shoulder where the bars meet, one each side of the lower bar, and a 50 kN load hangs from the lower end100 mm100 kN100 kN50 mm50 kN
  1. (A)15.0
  2. (B)25.0
  3. (C)35.0
  4. (D)45.0

Answer: (B) 25.0 Official key: B

  1. The two 100 kN loads hang from the shoulder symmetrically about the bar axis, so every cross-section carries pure axial tension; there is no bending.
  2. Lower bar (50 mm square): only the 50 kN end load is below any cut, so .
  3. Upper bar (100 mm square): a cut above the shoulder has all three loads below it, .
  4. .
  5. The larger value governs: (B) 25.0, in the upper bar, even though it is four times the area of the lower bar.

Trap: counting only one shoulder load gives , option (A), and adding the two bar stresses, , gives option (D). Stresses in members in series are compared, never added.

Where this shows up in industry

Hanger rods in suspended ceilings, pipe racks and bridge decks are checked the same way: the rod near the support carries everything hung below it, so it is the stressed one, which is why hanger sizes step down along the load path.

GATE 2023 · CE2 · Q.56NAT · 2 marksStress, strain, axial and thermal members

Shear stress coefficient from the displacement field u = Cx²y, v = 0 of a plane-stress plate

A 2D thin plate with modulus of elasticity, , and Poisson's ratio, , is in plane stress condition. The displacement field in the plate is given by and , where and are displacements (in m) along the and directions, respectively, and is a constant (in ). The distances and along and , respectively, are in m. The stress in the direction is , and the shear stress is . What is the value of (in , in integer)?

Answer: Official key: 5 to 5

  1. Strains from the displacement field: , and .
  2. Plane stress: , which here is .
  3. Matching : .
  4. Shear modulus , so .
  5. .

Trap: using the uniaxial law gives and ; multiplying the shear strain by instead of gives . Plane stress needs the factor, and shear always goes with .

Where this shows up in industry

Finite element software works in exactly this order: it solves for nodal displacements, differentiates them into strains and applies the plane stress or plane strain law to get stresses. Choosing the wrong one changes every stress it reports.

GATE 2026 · CE1 · Q.51NAT · 2 marksStress, strain, axial and thermal members

Force in a spring when a 3 m rod joined to it between fixed supports is heated by 100 C

A homogenous, linearly elastic rod AB is connected to a linearly elastic spring BC in between the fixed supports at A and C, as shown in the figure. The cross-sectional area, modulus of elasticity, and the coefficient of thermal expansion of the rod AB are 500 mm2, MPa, and per , respectively. The stiffness () of spring BC is 2500 N/mm.

The internal force (in kN) that will develop in the spring BC when the temperature of rod AB is increased by is _________ (rounded off to one decimal place).

Rod AB, 3 m long, fixed to a wall at A and joined at B to a spring BC of stiffness 2500 N/mm, whose other end C is fixed to a second wall3 mk = 2500 N/mmABCRedrawn, not to scale

Answer: 7.2 kN (compression) Official key: 7.0 to 7.4

  1. Free expansion of AB: mm.
  2. A and C are fixed, so the total length cannot change. The rod and the spring carry the same force in series, and their shortenings add up to .
  3. Rod stiffness: N/mm.
  4. , so N.
  5. Answer 7.2 kN, compression in the spring.

Trap: treating the rod as rigid gives kN, and fixing the rod at both ends gives kN; both are outside the key.

Where this shows up in industry

Expansion joints, bellows and elastomeric bearings play the part of the soft spring here. By letting part of the thermal movement happen, they cut the force a fully restrained member would develop by a large factor, from 36 kN to 7.2 kN in this example.

GATE 2026 · CE2 · Q.16MCQ · 1 markStress, strain, axial and thermal members

Which condition must a plane strain problem in the X-Y plane satisfy?

A plane strain problem (in X-Y plane) must satisfy the condition:

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Plane strain in the X-Y plane means the body cannot strain out of that plane: every strain component with a in it is zero, , and the in-plane strains depend on and only. That is (B).
  2. (A) is wrong: with , Hooke's law gives , which is not zero in general. belongs to plane stress.
  3. (C) is wrong: in plane strain.
  4. (D) is not a condition at all: equal in-plane strains, for example , are a perfectly valid plane strain state.
  5. Answer (B).

Trap: (A) is the plane stress condition. The two are mirror images: plane stress zeroes the out-of-plane stresses and lets develop; plane strain zeroes the out-of-plane strains and lets develop.

Where this shows up in industry

Long structures with a constant cross-section, such as gravity dams, retaining walls, tunnels and buried pipes, are analysed as a one-metre plane strain slice in finite element software, because the length restrains strain along the axis; plane stress elements there would understate the stiffness.

GATE 2026 · CE2 · Q.50NAT · 2 marksStress, strain, axial and thermal members

Bars BCD and FG fixed at B and G with a 2 mm gap at D-F: reaction at B for 20 kN at C

Linearly elastic, homogeneous, uniform bars BCD and FG shown in the figure have fixed supports at B and G, respectively. For both the bars, axial rigidity is 20000 kN. A gap of 2 mm exists between D and F prior to application of any load (i.e. P = 0). Small deformation and infinitesimal strain assumptions are valid for the given bars.

(Figure not to scale)

The magnitude of the horizontal reaction (in kN) at B after application of the axial force P of 20 kN at C is ______ (rounded off to the nearest integer).

Bar BCD fixed at B, 10 m long with point C at its middle, and bar FG fixed at G, 5 m long; a 2 mm gap between ends D and F; an axial force P acts to the right at CP2 mmgapBCDFG5 m5 m5 mRedrawn, not to scale

Answer: 16 kN Official key: 16 to 16

  1. First check whether the gap closes. Without bar FG, C moves m mm. Segment CD carries no force, so D moves the same 5 mm, more than the 2 mm gap. Contact happens.
  2. Let the contact force be . Then BC carries (tension), CD carries (compression) and FG carries (compression).
  3. Compatibility: movement of D gap shortening of FG:
  4. , so kN.
  5. Reaction at B kN, and at G it is kN.
  6. Answer 16 kN.

Trap: ignoring the gap gives and 13.33 kN; forgetting the shortening of CD gives 14 kN; assuming the gap stays open gives 20 kN. All three are outside the key.

Where this shows up in industry

Expansion gaps in rails, bridge decks and pipelines work on the same principle: until the gap closes a member moves freely, and only the movement beyond the gap generates force, so designers size the gap so that it never closes under the extreme temperature or load case.

From GATE prep to a structural design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.