GATE Civil: Calculus and Vector Calculus (limits, maxima, integrals, Fourier series, curl), previous-year questions solved

Every calculus and vector calculus question from the ten official GATE Civil papers of 2022-2026: 21 questions (3 NAT, 13 MCQ, 5 MSQ) on limits, continuity and differentiability, maxima and minima, errors by differentials, definite and improper integrals, Fourier series, and gradient, divergence and curl, each solved step by step and checked by a script against the official key. Engineering mathematics is Section 1 of the GATE CE syllabus and stays the same in GATE 2027.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 9 of 21 questions on this page

GATE 2022 · CE1 · Q.45MSQ · 2 marksLimits, continuity, maxima and minima

Is f(x) = max{3 - x, x - 1} continuous, differentiable, and does it have a local minimum or maximum at x = 2?

Let denote the maximum of two real numbers and . Which of the following statement(s) is/are TRUE about the function ?

  1. (A)It is continuous on its domain.
  2. (B)It has a local minimum at .
  3. (C)It has a local maximum at .
  4. (D)It is differentiable on its domain.

Answer: (A, B) Official key: A, B

  1. The two lines meet where , at , with value 1. For the larger one is and for it is , so , a V with its vertex at .
  2. (A) True: the maximum of two continuous functions is continuous, and both pieces give 1 at .
  3. (B) True: for every , so is a local (in fact global) minimum.
  4. (C) False: the values on both sides of are larger, not smaller.
  5. (D) False: the slope just left of is and just right is . A corner has no derivative.
  6. Answer: (A, B).

Trap: assuming a minimum needs . At a corner the derivative does not exist and the point is still the minimum, so check the one-sided slopes or simply sketch the V.

Where this shows up in industry

Design envelopes behave like this function. The bending-moment envelope over many load combinations in STAAD.Pro or ETABS is the maximum of several curves, so it is continuous but has corners where the governing combination switches, and the worst value can sit exactly at such a corner.

GATE 2022 · CE2 · Q.29NAT · 1 markLimits, continuity, maxima and minima

If the radius of a 5 cm rod is measured with 0.2 % error, what is the percentage error in its area?

The error in measuring the radius of a 5 cm circular rod was 0.2%. If the cross-sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is______. (round off to two decimal places)

Answer: 0.40 % Official key: 0.39 to 0.41

  1. , so : the relative error in doubles in the area.
  2. The relative error in is 0.2 %, so the error in is %.
  3. In absolute terms: , and , which is 0.4 % of .
  4. Exact check: , that is 0.4004 %, which rounds to 0.40 %. The 5 cm radius does not change the answer, because relative errors do not depend on size.

Trap: copying 0.20 % from the radius. The power of in the formula multiplies the percentage error; for the volume of a sphere it would triple.

Where this shows up in industry

Error propagation sets the measurement precision needed on site: an error in a pipe diameter doubles in the flow area and so in the computed discharge, and an error in a bar diameter doubles in its steel area, which is why bar and specimen dimensions are measured to tight tolerances in quality control.

GATE 2022 · CE2 · Q.36MCQ · 2 marksLimits, continuity, maxima and minima

On 1 to 3, where are the zeros, local maximum and minimum of x cubed - 6x squared + 11x - 6, and is f'' positive?

Consider the polynomial on the domain given by . The first and second derivatives are and .

Consider the following statements:

I. The given polynomial is zero at the boundary points and .

II. There exists one local maxima of within the domain .

III. The second derivative throughout the domain .

IV. There exists one local minima of within the domain .

The correct option is:

  1. (A)Only statements I, II and III are correct.
  2. (B)Only statements I, II and IV are correct.
  3. (C)Only statements I and IV are correct.
  4. (D)Only statements II and IV are correct.

Answer: (B) Only statements I, II and IV are correct. Official key: B

  1. Factor: , so . Statement I is true.
  2. gives , that is and , both inside .
  3. . At , : a local maximum (), so II is true. At , : a local minimum, so IV is true.
  4. is negative for and positive for , so III is false; is an inflection point.
  5. Only I, II and IV hold: (B).

Trap: (A) accepts III because near . Check the whole interval: a curve with both a local maximum and a local minimum inside it must change its concavity in between.

Where this shows up in industry

Finding maxima and minima from derivatives is how the critical section of a beam is located: shear force is the derivative of bending moment, so the maximum moment sits where the shear force crosses zero, and the maximum deflection sits where the slope of the elastic curve is zero.

GATE 2023 · CE1 · Q.48MSQ · 2 marksLimits, continuity, maxima and minima

Is e^x times |sin x| continuous, differentiable, periodic or bounded?

For the function ; , which of the following statements is/are TRUE?

  1. (A)The function is continuous at all
  2. (B)The function is differentiable at all
  3. (C)The function is periodic
  4. (D)The function is bounded

Answer: (A) Official key: A

  1. (A) True. , and the absolute value are all continuous, and products and compositions of continuous functions are continuous.
  2. (B) False. At every the factor has a corner. At the left derivative is and the right derivative is ; they differ, so there is no derivative there.
  3. (D) False. At , and , which grows without limit as increases.
  4. (C) False. A continuous periodic function repeats its values over one period, so it is bounded. is unbounded, so it cannot be periodic. Each hump is times taller than the one before.

Answer: (A) only.

Trap: alone is periodic and bounded, so (C) and (D) look true. The factor destroys both.

Where this shows up in industry

Growing oscillations of the form exponential times sine describe an unstable response, such as aerodynamic flutter of a long-span bridge deck or a structure driven at resonance with negative damping. Recognising unbounded growth in a time history is the first check in wind tunnel and dynamic analysis reports.

GATE 2024 · CE2 · Q.14MCQ · 1 markLimits, continuity, maxima and minima

Does f(x) = x^3 - 27x + 4 for x from 1 to 6 have a maxima, minima, saddle or inflection point?

The function , has

  1. (A)Maxima point
  2. (B)Minima point
  3. (C)Saddle point
  4. (D)Inflection point

Answer: (B) Minima point Official key: B

  1. gives ; only lies in .
  2. , so : a local minimum, with . (B) Minima point.
  3. (A): no stationary point in the interval has . (C): a saddle point belongs to functions of two or more variables. (D): is zero only at , outside the interval, so there is no inflection point.

Trap: the largest value on the interval is at the end point, (and ), but there ; an end-point extreme is not a maxima point in the sense of , . The root , the local maximum, lies outside the interval.

Where this shows up in industry

Setting a derivative to zero and checking the second derivative is how engineers locate the section of maximum bending moment in a beam (where shear is zero), the most economical depth of a canal section, or the cut-off that minimises total cost in an earthwork or pipeline design.

GATE 2025 · CE1 · Q.36MCQ · 2 marksLimits, continuity, maxima and minima

What is the limit of x minus the square root of (x squared plus x) as x tends to infinity?

The value of is equal to

  1. (A)-1
  2. (B)-0.5
  3. (C)-2
  4. (D)0

Answer: (B) -0.5 Official key: B

  1. Direct substitution gives , an indeterminate form, so rationalise.
  2. Multiply and divide by the conjugate: .
  3. Divide top and bottom by (positive for large ): .
  4. As , , so the limit is , option (B).
  5. Numerical check: at the expression is .

Trap: (D). Both terms grow like , so it is tempting to cancel them to 0, but for large , which leaves .

Where this shows up in industry

Rationalising an infinity minus infinity form also keeps design spreadsheets accurate: formulas such as the quadratic root for the neutral axis depth of an RCC section subtract two nearly equal large numbers and lose digits, and the conjugate form used here avoids that loss.

GATE 2025 · CE1 · Q.48NAT · 2 marksLimits, continuity, maxima and minima

Maximum value of h(x) = -x^3 + 2x^2 on the interval [-1, 1.5]

The maximum value of the function in the interval [-1,1.5] is equal to __________ (rounded off to 1 decimal place).

Answer: 3.0 Official key: 2.9 to 3.1

  1. On a closed interval the maximum is at a stationary point or at an end point, so check both.
  2. gives and , both inside .
  3. Stationary values: (a local minimum) and (a local maximum).
  4. End values: and .
  5. The largest of these is : the maximum is 3.0.

Trap: stopping at the local maximum gives . The cubic rises again to the left of , and the end point is higher.

Where this shows up in industry

Closed-interval maxima are how the governing value along a member is found: the largest bending moment or deflection along a span, or the highest pressure along a pipeline, is taken from the stationary points and the ends, and the end value often governs, as with the support moment of a cantilever.

GATE 2025 · CE2 · Q.44MSQ · 2 marksLimits, continuity, maxima and minima

Local maximum and local minimum of f(x) = x^3 - (15/2)x^2 + 18x + 20

Consider the function given below and pick one or more CORRECT statement(s) from the following choices.

  1. (A) has a local minimum at .
  2. (B) has a local maximum at .
  3. (C) has a local minimum at .
  4. (D) has a local maximum at .

Answer: (A, D) Official key: A;D

  1. Stationary points: , so and .
  2. Second derivative: .
  3. At : , a local minimum, so (A) is correct and (B) is wrong.
  4. At : , a local maximum, so (D) is correct and (C) is wrong.
  5. Values confirm it: is higher than . Correct: (A) and (D).

Trap: for a cubic with positive leading coefficient the curve rises, falls, then rises, so the smaller root is the maximum. Assuming the larger gives the maximum picks (B) and (C).

Where this shows up in industry

The first and second derivative tests locate the point of maximum sagging moment in a beam (where shear is zero) and distinguish it from a point of minimum, and the same test is used when optimising section depth or reservoir storage for least cost in design studies.

GATE 2026 · CE2 · Q.36MCQ · 2 marksLimits, continuity, maxima and minima

For f(x) defined as a 3x3 determinant with constant p, what is the third derivative of f at x = 0?

Let

where is a constant.

The value of at is

  1. (A)
  2. (B)
  3. (C)
  4. (D)independent of

Answer: (D) independent of Official key: D

  1. Only row 1 depends on , so is the same determinant with row 1 replaced by its third derivatives: .
  2. At that row is , identical to row 2. A determinant with two equal rows is zero, so for every .
  3. Check by expansion: , so , and .
  4. The value does not change with : (D) independent of .

Trap: keeping only the cofactor gives (option A); the term contributes at and cancels it exactly.

Where this shows up in industry

Determinants whose entries are functions of a variable are routine in structural dynamics and stability: the frequency determinant of a building model, built from its stiffness and mass matrices, and the buckling determinant of a frame are such functions, and their derivatives drive the root search inside analysis software.

From GATE prep to a structural design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.