Aim:For the given model, check for the geometrical errors and perform Topology cleanup and mesh for three different cases. Introduction: A pressure valve is a type of safety valve used to control or limit the pressure in a system,basically it was designed to control or relieve overpressure levels for optimal functionality…

Aim:For the given model, we need to check for geometrical errors to make appropriate volumes. Create and assign PIDs. Perform surface mesh with the given target lengths as per PIDs and to perform Volumetric mesh for the required volumes. Introduction: A turbocharger is a forced induction device. It is used to…

Aim:For the given model, check and solve all geometrical errors on half portion and Assign appropriate PIDs and Perform meshing with the given Target length and element Quality criteria. After meshing the half model, Do symmetry to the other side and create and mesh wind tunnel. Introduction: Bayerische Motoren Werke AG,…

Aim:For the given models, check for the geometrical errors and delete surfaces which are unwanted for Surface wrap. After clearing geometry, Merge all 3 models and perform surface wrap. Introduction: Engine: DOHC 16v refers to a 4-cylinder internal combustion engine with 4 valves in each cylinder and two camshafts. The…

Aim:For the given Tesla cybertruck  model, check and solve all geometrical errors and Assign appropriate PIDs. Perform meshing with the suitable Target length and element Quality criteria. create a wind tunnel around the model and deploy volumetric mesh on the volume. Introduction: The Tesla Cybertruck is…

Aim:  To set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C.  Use of k-epsilon and k-omega SST model for the first case to analyze which is more suitable model for further cases. To try different cases for the given velocity and…

Aim:  To set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C.  Use of k-epsilon and k-omega SST model for the first case to analyze which is more suitable model for further cases. To try different cases for the given velocity and…

Aim: Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street. Simulate the flow with the steady and unsteady case and calculate the Strouhal Number for Re= 100.  Calculate the coefficient of drag and lift over a cylinder by setting the Reynolds number to 10,100,1000,10000 & 100000. (Run…

Aim: To perform CFD analysis for one part of Ahmed  body and in fluent to use the symmetry boundary condition to perform the simulation. To Run the simulation for the velocity of 25 m/sec with the default air properties in fluent. plot for Velocity and pressure contours.  plot the drag coefficient for a…

Aim: To give a brief description of why and where a CHT analysis is used. To Maintain the y+ value according to the turbulence model and justify the results.   Calculate the wall/surface heat transfer coefficient on the internal solid surface &  also to show the velocity & temperature contours in…

Aim:  To Perform the Rayleigh Taylor instability simulation for 2 different mesh sizes with the base mesh being 0.5 mm and to  Compare the results by showing the animations To Observe the differences in the animation and explain the effect of mesh size on simulation. Also, explain why a steady-state approach might not…

Aim: To Perform a steady-state conjugate heat transfer analysis on a model of a graphics card.  To Run the simulation by varying the velocity from 1m/sec to 5m/sec for at least 3 velocities and discuss the results. To Find out the maximum temperature and heat transfer coefficient attained by the processor. To Prove…

Aim:- To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop.   Objective:- To write a few words about any four empirical models used to calculate the cyclone separator efficiency.  To perform an analysis on a given cyclone separator model by varying the particle…

Aim: To perform a parametric study on the gate valve simulation by setting the opening from 10 % to 80%. objective:  To Obtain the mass flow rates at the outlet for each design point. To Calculate the flow coefficient and flow factor for each opening and plot the graph. To Discuss the results of the mass flow rate…

Aim:To download the connectors & Connector clip cad data & define it as Electrical Connector using Electrical Part design Workbench and to define all the necessary properties to Connectors & Clip.  Introduction: Wire harness connectors provide an uninterrupted electronic signal between a…