Objective: To design individual parts and assembly of American chopper using Solidworks and also perform appropriate rendering using Solidworks visualize.   Introduction: An American chopper start designing from individual parts using Solidworks. solid works are easy to learn and use the software. start modelling…

Objective: To design individual parts and assembly of American chopper using Solidworks and also perform appropriate rendering using Solidworks visualize. Introduction: An American chopper start designing from individual parts using Solidworks. solid works are easy to learn and use the software. start modelling from…

Radar Mast and Yacht Assembly Radar Mast Yacht Assembly Project Yacht Assembly Objective: This project of yacht design and I believe by working on a complex design such as a yacht I learn more techniques and features which can help to improve my tool skills in the module.   Introduction: It is about yacht design Made…

Casing Design   Objective:- The design of casing design with the help of basic commands and there used for modelling of the NX cad.   Introduction:- This report on the casing design model with the help of Siemens NXcad software is also, especially for sheet metal design. NX Cad sheet metal is an easy and…

Title of the Project:- Box Assembly Using Advanced sheet metal design in the NX Cad   Objective:- To Design a box assembly using NX Cad Application.   Introduction:- 1.Sheet metal is formed by an industrial process into thin. it is a design application that using manufacturing design in NX Cad application. …

Title of the Project:- Odd Shaped Enclosure Objective:- To Create design In Sheet metal and drafting of Odd Shaped Enclosure. Introduction:- Sheet metal is an industrial design process. Sheet metal is used in metalwork and it can be bend, cut, punch, die, etc. to create the enclosure by the solid model and wrapping the…

Title of the Project:- Bracket Objective:- To create a bracket using NX Sheet metal. Introduction:- To understand create of Bracket using advanced sheet metal software. it has used some new commands and features. Design methodology:-  Description:- In this module, we will see about the feature and commands…

Title of the Project:- Bracket-ll Using Advanced Sheet Metal Objective:- To design a bracket using advanced sheet metal application Siemens NX Cad. Introduction:- Sheet metal is formaed by an industrial process. it is a design application that using manufacturing design in NX Cad appliaction. NX Cad is formerly known…

1. Hello, Mr.D.S.Pughazhyendhii as you have fond of big cars, I suggest your 8 to 10 lakh on-road budget. I am suggesting you Renault Triber which comes in 7 seater variant option it had 1liter engine, power 71bhp at 6250rpm, torque 96Nm at 3500rpm, fantastic mileage of 20kmpl in the highway and 18kmpl in the city, 40liter…

In Indian road conditions, a cars underbody is most prone to corrosion. Underbody coating provides long term protection from corrosion to car’s underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible but are prone to corrosion.   Benefits•…

Hood Desgin Introdution:- A car hood is also known as bonnet. Hood is assemble in front side of car's and it covers engine and in sports car boot space. Hood assembly consist of different parts that combine to be in vehicle. 1. Hood Outer Panel 2. Hood Inner Panel 3. Hinges assembly      i) Hinge hood side…

Aim:- To calculate the section of modulus of the designed hood and analyze the hood by increasing the depth of the inner panel.     Section Modulus Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section…

Wheel arch:- The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change was that the front wheel arch was cut higher into the fender. Corrosion had occurred around the splash plate at the back of the wheel arch. The car has big, high-definition…

Fender Design   Objective:-  To Design the fender mounting on the drip area, still area, Baffle area, and the A-pillar using the NX Cad.  Introduction:- Fender's primary purpose is to prevent sand, mud, rocks, liquids, and other roads spray from being thrown into the air by the rotating tire. Fenders…

Roof Design Objective:- To design car roof with essentials like ditch area, front roof, bow roof, reinforcements central and rear roof rail. To perform the calculations of the heat distortion and snow load criteria determine whether the bow roofs are at the correct position. Find the moment of inertia and draft analysis…

Back Door Design   Objective:-  To use the provided styling surface to come up with a back door and use appropriate design methodologies and male the necessary reinforcements and emboss. Introduction:- The truck or boot of a car is the vehicle's main storage or cargo compartment, often a hatch at the rear of…

Draft Analysis   The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on colour ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values…

Base Bracket Design Objective: To create tooling axis, class B, class C Surface and make it a solid model. Draft analysis of class A surface and the final plastic component.   Introduction: The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis…

Switch Bezel Design   Objective: To create tooling axis, class B, class C Surface and make it a solid model. Draft analysis of class A surface and the final plastic component.   Introduction: The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of…

840752   Objective: Create CLASS B and Class C Surface for the Door Armrest using the given Class A Surface.  Use the given Class A Surface of the Door for reference.  Use the Close Surface feature to make a solid body from the surface.  Use the publication option and publish the Class A, Class B, Class…

Coin Holder     Objective:   To design coin holder as per automotive OEM Standard.   • Create B Class and C Class and tooling axis.   • Convert close lose the surface into the solid body and provide a thickness of 2.5mm.   • Performing draft analysis to verify the creation of…

  Core & Cavity Design     Objective: To create the core and cavity for the switch bezel considering all design rules.   Tooling Axis:   it is the axis in which the direction core and cavity open. this is very important for the production of plastic components, most of the defects will…

Attachment Feature Creation     Design Rules of Ribs Creation   Objective: to design ribs on the coin holder considering every design rule considered in the industry.     Class-B surface contains all the engineer data required for the model to be completed. This data involves designing various…

Screw Boss and Dog House           Objective:- To create Center Console Coin Holder and Screw Boss and Dog house and add thickness to it and generate the Draft Analysis on a solid surface final component.   Introduction:- Boss features are commonly found in injection moulding designs. They…