Mix Design for M35 Grade Concrete Aim  The mix design for M35 grade of concrete with fly ash will be calculated and ratio will be obtained. Procedure  Step 1 : Stipulations for proportioning  1. Grade designation : M35 2. Type of cement: OPC 53 grade conforming to IS 8112 3. Type of mineral admixture: Fly…

Aim :  To sketch a G+1 residential building plan according to vaastu shastra and to calculate all loads in the building as per IS code.  Procedure :  GROUND FLOOR     FIRST FLOOR  Dimensions  All columns are 300 x 300mm All beams are 300 x 450mm Slab thickness is 125mm Height of…

Aim  To create the geometries from p1 to p2 using all the coordinate system methods and using the line tool and circle tool. Procedure  Absolute Coordinate System  Relative Coordinate System              To draw the profile and trusses using any coordinate system methods …

Aim  To create a floor plan, footing detail and isometric view using AutoCad Procedure  Open AutoCad application Type Qnew and open new drawing In create new drawing select wizard Select advanced setup Set units measurement as engineering, angle as decimal degree, angle measure as east, angle direction as clockwise,…

1.Decimal Aim   Open AutoCad application Set units measurement as engineering, angle as decimal degree, angle measure as east, angle direction as clockwise, area as 9x12 inches and close the tab. Now enable the dynamic input, right click dynamic input and choose dynamic input settings. Go to pointer input setting…

1. RESIDENCE PLAN AIM TO SKETCH THE GIVEN RESIDENCE PLAN  PROCEDURE DRAW THE OUTLINE OF THE PLAN INNER WALL GIVEN USING LAYER PROPERTIES GIVE DIFFERENT COLOURS FOR DIFFERENT ELEMENTS THEN USING OFFSET DRAW 9.0' DISTANCE ANOTHER OUTLINE. SHOWING THE WALL THICKNESS GIVE WALL THICKNESS 4.5' WHEREVER NECESSARY USING ARC…

1. COLUMN SCHEDULE Aim To create the column schedule given. Procedure Create rectangle of 60' x20 '  ,explode it . Divide the 60' into 10' columns nad again divide each 10' to 5' by using offset command . Command "O" - select the left side line and give offset distance as 10' first and for the second as 5'. Create…

1.WARDROBE Aim To draw the elevation and details of a wardrobe given Procedure Firstly Units are set to mm that is decimel In the command line type rec>2800, 2600 and type offset from the top of dimensions 12 and 488 mm. In the command line type offset the offset from the side at the distance of 608.75 and 365…

Aim To draw the plan, section AA and section BB of a building Procedure For PLAN: Given outer wall thickness as 250mm and inner wall thickness as 125mm. Draw XL -H and XL-V , give the thickness of wall . Give the dimension of rooms Bedroom (3100x3100)mm by offset command. Give inner wall dimesnion as 125mm by offset method.…

AIM & INTRODUCTION To create a floor plan with plot size 60'x20' and develop structural drawings in AutoCad 1. Architectural Drawing -Floor Plan -Elevations -Sections 2. Structural Drawing -Column layout -Beam Layout -Footing Plan PROCEDURE 1. Architectural Drawings Open Autocad and open new drawing Drawing units are…

1. TEMPLATES Aim To create the given templates and convert into blocks Procedure The Tables are drawn using LINE and OFFSET commands. The text is given using DTEXT command. It is editted using Manage text styles from the Annotate panel in the ribbon. The given text is Times New Roman.shx. The text is copied and pasted…

1. Kitchen Layout Aim To create the layouts of the Kitchen and provide hatches pattern Introduction To create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. First drawing the below counter plan and then the above counter plan…

1. Aim To create a layout of the Plan and Section A of the project in Challenges 7 Introduction Create a layout of the Plan and Section A of the project in Challenges 7 Using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Procedure…

1. Aim To create the given 3d furiniture model in autocad Introduction To create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. Procedure UN command is given and units are set to engineering. The precision is set to 0'-0'0" Change the workspace to 3D modelling Draw a vertical line of…

1. Aim To create a 3D Isometric View of the building with plan and elevation given. Introduction Create the 3d isometric view of building plan and create windows Procedure AutoCAD is opened with Imperial setting as default. In units of measurement Architectural is selected. Precision is set to 0'-0.0". First 2d plan given…

Aim To create the 3D model of the residential building Introduction To create the 3D model of the residential building with rendered view The 3D model is developed using the 3D modelling workspace in AutoCAD. It is then rendered as required. Procedure AutoCAD is started with Metric as default setting. The Type is set to…

1. Aim To model a Ceiling from the architecture tab above the walls at the first-floor level Procedure 1. Open the previous project from week 3 2. From the architectural tab select ceiling option 3. Open level 1 option from project browser 4. Select all rooms to create ceiling 5. Now open the 3D view option to see the…

1. Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School I select Multi-Unit Residential Apartment type of structure 2. Aim To give reasonable details…

1. a) 1. Concrete is crushed and reinforcement is visible 2. Beam top portion looks good and safe, because of the slab flange 3. The cracks start from bottom to top 4. Rebar yielding occurs in bottom 5. It is a flexural failure due to a reversal of stress during earthquake 6. During this failure top support experiences…

1. Static Analysis and Dynamic Analysis Static Analysis : Static analysis can only be performed if the system being simulated does not depend on time,and if the loads being applied are constant. Static analysis don't consider inertia. Static refers to the force that has constant size,Position and Direction on or with in…

1. Symmetry : Investigation of the framing plan with respect to symmetry in X direction If we split the plan vertically half, it will look mirrored, so it is symmetric in x direction. Investigation of the framing plan with respect to symmetry in Y direction If we split the plan horizontally half, it will look mirrored,…

1. a) Restraint of floor shrinkage Full restraints at all corners Corners are left free but restraints along the edges Non-uniform restraints b) The lateral stiffness Comparatively lower stiffness in both X and Y Uniform and comparatively higher lateral stiffness in both X and Y Non uniform lateral stiffness in both X…

1. Modelling of 25 storey building in ETABS Open the Etabs software and click new model Setup model initialization and set design codes Give custom grid spacing Give spacing as per the question in both x and y direction Then edit story data and add stories Add 22 stories more to 25 stories Give story1 as master story and…